JVC HR-S8700EK, LPT0319-001A setup guide With RF Connection, Test Signal

Page 69

1

2

1

2

– –:– –

1 2 3

4

5

6

7 8 9

0

3

4

4

3OK

PR

61

With RF Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■the connected TV is turned on.

■batteries have been installed in the remote control.

ACCESS VIDEO CHANNEL SET MODE

1 Press and hold down STOP on the recorder until the display panel shows the following.

SET VIDEO CHANNEL

2 Press PR+ or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area. Refer to list on page 68 for details of broadcast stations in your area.

(Ex.) If channel 36 is available in your area

Then set your TV to UHF channel 36. (Refer to the instructions supplied with your TV set for how to do this.)

●If the two vertical white bars appear clearly on the screen as shown in the illustration at bottom left, go to step 3.

●If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

IMPORTANT

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

EXIT VIDEO CHANNEL SET MODE

TEST SIGNAL

The channel on which the screen on the left appears clearly in step 2 is your Video Channel.

3 Press OK.

To view picture signals from the video recorder, set your TV to the Video Channel.

Image 69

Contents HR-S8700EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Connect Video Recorder to TV Back of TVBack of Recorder Video Connection Mains outlet Mains Power CordWith the AV or S-VIDEO connection Before performing the following procedure, make sure thatTion pg and the TV is turned on, Go to item10 or If -- appears on the display panel, refer Remote control while downloading isLink screen will appear. Then the Guide Program number setIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notAccess Mode SET Screen Access Main Menu ScreenLink Functions Turn on the RecorderSatellite Receiver Control Setting Enter Satellite RECEIVER’S Brand Select Satellite RECEIVER’S Channel for TestingCheck Result of Test CodeLoad a Cassette PlaybackFind Programme Start Point Start PlaybackActivate HIGH-SPEED Search Pause During PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayAccess Video PLUS+ Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Program Screen Enter Pluscode NumberPDC Recording Timer WarningEnter Programme Express Timer ProgrammingStart Time TimeTimer Mode SET PDC ModeSET Tape Speed Return to NormalCheck, Cancel And Replace Programmes Cancel or Change Programme Setting When programmes overlap each otherConfirm Overlapping Programmes ModifyNavigation Return to Normal Screen Check MemoryTurn OFF Navigation Turn Off NavigationTitle Editing Access Find Blank Space ScreenSelect Tape Number Load a CassetteEnter Character Access Video Navigation ScreenEdit Tape Title Select Tape NumberSelect Programme Select CategoryEdit Programme Title Category Data Delete ProgrammeDelete Tape Data Delete Programme DataAccess Tape NO. Screen Access Find Title ScreenAccess Video Finding TitleSelect Programme Access Category Screen Access Date ScreenSelect Programme Load a Cassette Sorting By DateNavigation Check Memory Title Editing Access Main Menu Screen Select Programme Return to Normal Screen Finding Title Access Date Screen Adjust Tracking Playback Picture AdjustmentOverride Automatic Tracking ManuallyMode SET ModeDigital 3R Video StabilizerAdjust Audio Access REC LevelSelecting Sound You Want Control ScreenSoundtrack Selection Receiving Nicam Stereo And Bilingual ProgrammesDuring Playback Type of Broadcast On-screen Display Being ReceivedActivate Index Search Looking For Scene You WantSkip Over Unwanted SectionsSelect S-VHS Mode Recording According To Tape TypeSuper VHS S-VHS VHS ET and VHS Select B.E.S.T. Mode Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Recording Start PlaybackPlayback During B.E.S.TAutomatic Satellite Programme Recording Connector TV Aerial cable Audio in connectorSatellite Receiver Unit AerialSelect L-2 Select Mode Access Main Menu ScreenREC Mode ScreenRemove Power Supply Remote Control FunctionsSET Remote Control Code RE-SUPPLY PowerTV Multi-Brand Remote Control Control Your TV Using Additional ButtonsSET TV Brand Code Operate TVBrand Code Satellite Receiver Multi Brand Remote ControlOperate Satellite Receiver NumberAccess Mode SET Access Main MenuControl SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Synchro Edit connector Lanc Cable not provided Synchro EditingPress Synchro /8again Repeat steps 4 6 as necessary SET Edit Mode Input ModeEdit To Or From Another Video Recorder SET Recording DECK’SRecorder Player SELECT/INPUT Setting OUTPUT/INPUT SettingAudio Dubbing Reset the Counter Insert EditingLocate END Point Start Editing Engage Insert EditingEND Insert Editing Press InsertAccess Initial SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Jlip ID NO. SET Screen Information On J TerminalOther Functions ENABLE/DISABLEON-SCREEN Display On-Screen DisplaySelect Power Save Mode Power Save ModePress %Þ to move the highlight bar pointer to Auto Timer Access Mode SET ScreenAuto SP→LP Timer Next Function MemoryEngage RECORD-PAUSE Mode Stop PlaybackResume Recording Speaker Television Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalPerform Auto Channel SET Tuner SetAuto Channel Set Pointer to Auto CHView Confirmation Screen Input Channel Storing Channels ManuallyEnter NEW Channel Information Close Confirmation ScreenChange Station Preset Position When Receiving a Scrambled BroadcastFine-Tuning Channels Already Stored Delete a ChannelEnter NEW Character Station Name TV Station And ID ListTV Station Channel Number Guide Clock Set Video Plus+ System Setup NumberGuide Program Number Set Questions And Answers Ä remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Recording Won’t stop blinking Record Safety tab removedOther Problems Front View IndexRear View VCR Display PanelTV Muting Button mutes sound Remote ControlFast Forward FF Button same as button on Remote Control LCDDA4 Double Azimuth helical Maximum recording time