JVC LPT0319-001A, HR-S8700EK setup guide OUTPUT/INPUT Setting, SELECT/INPUT Setting

Page 58

50ADVANCEDOPERATIONS(cont.)

L-1 OUTPUT/INPUT Setting

The AV1 (L-1) IN/OUT connector accepts and delivers either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set "L-1 OUTPUT" and "L-1 INPUT" to the appropriate mode depending on the type of unit connected to the rear panel AV1 (L-1) IN/OUT connector of this recorder.

1Press MENU to access the Main Menu screen.

2Press %Þ to move the highlight bar (pointer) to "OUTPUT/INPUT SET", then press OK or #.

3 Press %Þ to move the highlight bar (pointer) to "L-1 OUTPUT" or "L-1 INPUT".

4 For "L-1 OUTPUT"

Press OK or #to select "VIDEO" or "S-VIDEO".

a–VIDEO

: If a connected device's input is compatible only with regular video signals,

 

set to "VIDEO".

b–S-VIDEO

: If a connected device's input is compatible with Y/C signals, set to

 

"S-VIDEO". This setting will let you take advantage of higher-quality

 

S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that

 

is compatible with the Y/C signal.)

For "L-1 INPUT"

Press OK or #to select "VIDEO" or "S-VIDEO".

a–VIDEO

: If a connected device's output is compatible only with regular video

 

signals, set to "VIDEO".

b–S-VIDEO

: If a connected device's output is compatible with Y/C signals, set to

 

"S-VIDEO". This setting will let you take advantage of higher-quality

 

S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that

 

is compatible with the Y/C signal.)

5Press MENU to return to normal screen.

●If "L-1 OUTPUT" is set to "S-VIDEO", it is impossible to set "L-1 INPUT" to "S-VIDEO".

●If "L-2 SELECT" is set to "DECODER", it is impossible to set "L-1 INPUT" to "S-VIDEO".

 

OUTPUT/INPUT SET

 

 

L-1 OUTPUT

VIDEO

L-1

INPUT

VIDEO

L-2

SELECT

A/V

L-2

INPUT

VIDEO

[5°] = [MENU] : EXIT

L-2 SELECT/INPUT Setting

The AV2 (L-2) IN/DECODER connector accepts either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set "L-2 SELECT" to the appropriate mode depending on the type of unit connected to the rear panel AV2 (L-2) IN/DECODER connector of this recorder. Set "L-2 INPUT" to the appropriate mode depending on the output signals of the connected unit.

1Press MENU to access the Main Menu screen.

2Press %Þ to move the highlight bar (pointer) to "OUTPUT/INPUT SET", then press OK or #.

3 Press %Þ to move the highlight bar (pointer) to "L-2 SELECT" or "L-2 INPUT".

4 For "L-2 SELECT"

OUTPUT/INPUT SET

Press OK or #to select "A/V", "DECODER" or "SAT".

L-1 OUTPUT

VIDEO

a–A/V

: To use this recorder as the recording deck with the player connected to the

L-1 INPUT

VIDEO

 

AV2 (L-2) IN/DECODER connector, or to use the satellite receiver con-

 

 

 

 

L-2 SELECT

A/V

 

 

nected to the AV2 (L-2) IN/DECODER connector.

 

b–DECODER

L-2 INPUT

VIDEO

 

: To use a decoder connected to the AV2 (L-2) IN/DECODER connector.

 

 

 

c–SAT

: To view a satellite programme with the TV set while the recorder is turned

 

 

 

 

off. (☞ pg. 40)

 

 

 

 

[5°] =

 

 

For "L-2 INPUT"

[MENU] : EXIT

 

 

Press OK or #to select "VIDEO" or "S-VIDEO".

 

 

 

a–VIDEO

: If a connected device's output is compatible only with regular video

 

 

 

 

signals, set to "VIDEO".

 

 

 

b–S-VIDEO

: If a connected device's output is compatible with Y/C signals, set to

 

 

 

 

"S-VIDEO". This setting will let you take advantage of higher-quality S-VHS

 

 

 

 

pictures. (For connection, be sure to use a 21-pin SCART cable that is

 

 

 

 

compatible with the Y/C signal.)

 

 

 

5Press MENU to return to normal screen.

●If you have a satellite receiver or a decoder connected to the AV2 (L-2) IN/DECODER connector, be sure to set "L-2 SELECT" back to appropriate mode after editing.

●If you're not connecting a satellite receiver or a decoder to the AV2 (L-2) IN/DECODER connector, leave "L-2 SELECT" set to "A/V".

●The default setting is "A/V"; if the recorder's memory backup has expired due to a power cut or because the AC was removed from the recorder, "A/V" will be automatically selected when the power is restored to the recorder. If you are using a satellite receiver or a decoder, be sure to set "L-2 SELECT" back to appropriate mode.

●When "L-2 SELECT" is set to "SAT", "SAT" appears on screen or display panel instead of "L-2" or "L2".

●If "L-2 SELECT" is set to "DECODER", it is impossible to set "L-2 INPUT" to "S-VIDEO".

●If "L-1 OUTPUT" is set to "S-VIDEO", it is impossible to set "L-2 SELECT" to "DECODER".

Page 57 Page 59
Image 58
Page 57 Page 59
Contents HR-S8700EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Connect Video Recorder to TVBack of Recorder Mains outlet Mains Power Cord Video ConnectionTion pg and the TV is turned on, Before performing the following procedure, make sure thatWith the AV or S-VIDEO connection Go to itemLink screen will appear. Then the Guide Remote control while downloading is10 or If -- appears on the display panel, refer Program number setIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedLink Functions Access Main Menu ScreenAccess Mode SET Screen Turn on the RecorderSatellite Receiver Control Setting Check Result of Test Select Satellite RECEIVER’S Channel for TestingEnter Satellite RECEIVER’S Brand CodeFind Programme Start Point PlaybackLoad a Cassette Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayAccess Video PLUS+ Program Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Enter Pluscode NumberTimer Warning PDC RecordingStart Time Express Timer ProgrammingEnter Programme TimeSET Tape Speed SET PDC ModeTimer Mode Return to NormalCheck, Cancel And Replace Programmes Confirm Overlapping Programmes When programmes overlap each otherCancel or Change Programme Setting ModifyNavigation Turn OFF Navigation Check MemoryReturn to Normal Screen Turn Off NavigationSelect Tape Number Access Find Blank Space ScreenTitle Editing Load a CassetteEdit Tape Title Access Video Navigation ScreenEnter Character Select Tape NumberSelect Category Select ProgrammeEdit Programme Title Category Delete Tape Data Delete ProgrammeData Delete Programme DataAccess Video Access Find Title ScreenAccess Tape NO. Screen Finding TitleSelect Programme Load a Cassette Access Date ScreenSelect Programme Access Category Screen Sorting By DateNavigation Check Memory Title Editing Access Main Menu Screen Select Programme Return to Normal Screen Finding Title Access Date Screen Override Automatic Tracking Playback Picture AdjustmentAdjust Tracking ManuallyDigital 3R SET ModeMode Video StabilizerSelecting Sound You Want Access REC LevelAdjust Audio Control ScreenDuring Playback Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedSkip Over Unwanted Looking For Scene You WantActivate Index Search SectionsRecording According To Tape Type Select S-VHS ModeSuper VHS S-VHS VHS ET and VHS Playback/ Recording According To Tape Charac- teristics Select B.E.S.T. ModeS.T. Picture System Playback Start PlaybackRecording During B.E.S.TSatellite Receiver Unit Connector TV Aerial cable Audio in connectorAutomatic Satellite Programme Recording AerialREC Mode Access Main Menu ScreenSelect L-2 Select Mode ScreenSET Remote Control Code Remote Control FunctionsRemove Power Supply RE-SUPPLY PowerSET TV Brand Code Control Your TV Using Additional ButtonsTV Multi-Brand Remote Control Operate TVOperate Satellite Receiver Satellite Receiver Multi Brand Remote ControlBrand Code NumberControl SET Mode Access Main MenuAccess Mode SET Minimizing Picture Degradation While EditingEdit From Camcorder Synchro Editing Synchro Edit connector Lanc Cable not providedPress Synchro /8again Repeat steps 4 6 as necessary Edit To Or From Another Video Recorder Input ModeSET Edit Mode SET Recording DECK’SRecorder Player OUTPUT/INPUT Setting SELECT/INPUT SettingAudio Dubbing Insert Editing Reset the CounterLocate END Point END Insert Editing Engage Insert EditingStart Editing Press InsertAccess Jlip ID NO. SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Information On J TerminalON-SCREEN Display ENABLE/DISABLEOther Functions On-Screen DisplayPower Save Mode Select Power Save ModePress %Þ to move the highlight bar pointer to Auto SP→LP Timer Access Mode SET ScreenAuto Timer Next Function MemoryStop Playback Engage RECORD-PAUSE ModeResume Recording Connection To Stereo System Speaker TelevisionVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionAuto Channel Set Tuner SetPerform Auto Channel SET Pointer to Auto CHView Confirmation Screen Enter NEW Channel Information Storing Channels ManuallyInput Channel Close Confirmation ScreenFine-Tuning Channels Already Stored When Receiving a Scrambled BroadcastChange Station Preset Position Delete a ChannelEnter NEW Character TV Station And ID List Station NameTV Station Channel Number Guide Clock Set Number Video Plus+ System SetupGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Won’t stop blinking Record Safety tab removed RecordingOther Problems Index Front ViewRear View Display Panel VCRRemote Control TV Muting Button mutes soundRemote Control LCD Fast Forward FF Button same as button onMaximum recording time DA4 Double Azimuth helical
Top Page Image Contents