JVC LPT0319-001A, HR-S8700EK setup guide Other Problems

Page 82

74

SUBSIDIARYINFORMATION(cont.)

OTHER PROBLEMS

SYMPTOM

1.Whistling or howling is heard from the TV during camcorder record- ing.

2.When scanning channels, some of them are skipped over.

3.The preset cannot be changed.

4.Channel settings that were made manually seem to have changed or disappeared.

5.No channels are stored in the recorder's memory.

6.The remote control won’t operate the TV or satellite receiver.

POSSIBLE CAUSE

●The camcorder’s microphone is too close to the TV.

●The TV’s volume is too high.

●Those channels have been desig- nated to be skipped.

●Recording is in progress.

●After the manual settings were made, Auto Channel Set was performed.

●The TV aerial cable was not connected to the recorder when Auto Set Up was performed.

●The fully-wired 21-pin SCART cable was not connected between TV and the recorder when Preset Download was performed.

●The remote control brand setting is incorrect.

CORRECTIVE ACTION

Position the camcorder so its microphone is away from the TV. Turn the TV’s volume down.

If you need the skipped channels, restore them (☞ pg. 64).

Press PAUSE to pause the recording, change presets, then press PLAY to resume recording.

Perform manual setting again.

Turn off the recorder once and connect the TV aerial cable to the recorder properly, then turn on the recorder again. The recorder will try Auto Set Up again (☞ pg. 8).

Turn off the recorder once and connect the fully-wired 21-pin SCART cable to the recorder properly, then turn on the recorder again. Then perform Preset Download again (☞ pg. 9).

Re-set the remote control to the correct brand (☞ pg. 43, 44).

Image 82

Contents HR-S8700EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Connect Video Recorder to TVBack of Recorder Mains outlet Mains Power Cord Video ConnectionTion pg and the TV is turned on, Before performing the following procedure, make sure thatWith the AV or S-VIDEO connection Go to itemLink screen will appear. Then the Guide Remote control while downloading is10 or If -- appears on the display panel, refer Program number setIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedLink Functions Access Main Menu ScreenAccess Mode SET Screen Turn on the RecorderSatellite Receiver Control Setting Check Result of Test Select Satellite RECEIVER’S Channel for TestingEnter Satellite RECEIVER’S Brand CodeFind Programme Start Point PlaybackLoad a Cassette Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayAccess Video PLUS+ Program Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Enter Pluscode NumberTimer Warning PDC RecordingStart Time Express Timer ProgrammingEnter Programme TimeSET Tape Speed SET PDC ModeTimer Mode Return to NormalCheck, Cancel And Replace Programmes Confirm Overlapping Programmes When programmes overlap each otherCancel or Change Programme Setting ModifyNavigation Turn OFF Navigation Check MemoryReturn to Normal Screen Turn Off NavigationSelect Tape Number Access Find Blank Space ScreenTitle Editing Load a CassetteEdit Tape Title Access Video Navigation ScreenEnter Character Select Tape NumberSelect Category Select ProgrammeEdit Programme Title Category Delete Tape Data Delete ProgrammeData Delete Programme DataAccess Video Access Find Title ScreenAccess Tape NO. Screen Finding TitleSelect Programme Load a Cassette Access Date ScreenSelect Programme Access Category Screen Sorting By DateNavigation Check Memory Title Editing Access Main Menu Screen Select Programme Return to Normal Screen Finding Title Access Date Screen Override Automatic Tracking Playback Picture AdjustmentAdjust Tracking ManuallyDigital 3R SET ModeMode Video StabilizerSelecting Sound You Want Access REC LevelAdjust Audio Control ScreenDuring Playback Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedSkip Over Unwanted Looking For Scene You WantActivate Index Search SectionsRecording According To Tape Type Select S-VHS ModeSuper VHS S-VHS VHS ET and VHS Playback/ Recording According To Tape Charac- teristics Select B.E.S.T. ModeS.T. Picture System Playback Start PlaybackRecording During B.E.S.TSatellite Receiver Unit Connector TV Aerial cable Audio in connectorAutomatic Satellite Programme Recording AerialREC Mode Access Main Menu ScreenSelect L-2 Select Mode ScreenSET Remote Control Code Remote Control FunctionsRemove Power Supply RE-SUPPLY PowerSET TV Brand Code Control Your TV Using Additional ButtonsTV Multi-Brand Remote Control Operate TVOperate Satellite Receiver Satellite Receiver Multi Brand Remote ControlBrand Code NumberControl SET Mode Access Main MenuAccess Mode SET Minimizing Picture Degradation While EditingEdit From Camcorder Synchro Editing Synchro Edit connector Lanc Cable not providedPress Synchro /8again Repeat steps 4 6 as necessary Edit To Or From Another Video Recorder Input ModeSET Edit Mode SET Recording DECK’SRecorder Player OUTPUT/INPUT Setting SELECT/INPUT SettingAudio Dubbing Insert Editing Reset the CounterLocate END Point END Insert Editing Engage Insert EditingStart Editing Press InsertAccess Jlip ID NO. SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Information On J TerminalON-SCREEN Display ENABLE/DISABLEOther Functions On-Screen DisplayPower Save Mode Select Power Save ModePress %Þ to move the highlight bar pointer to Auto SP→LP Timer Access Mode SET ScreenAuto Timer Next Function MemoryStop Playback Engage RECORD-PAUSE ModeResume Recording Connection To Stereo System Speaker TelevisionVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionAuto Channel Set Tuner SetPerform Auto Channel SET Pointer to Auto CHView Confirmation Screen Enter NEW Channel Information Storing Channels ManuallyInput Channel Close Confirmation ScreenFine-Tuning Channels Already Stored When Receiving a Scrambled BroadcastChange Station Preset Position Delete a ChannelEnter NEW Character TV Station And ID List Station NameTV Station Channel Number Guide Clock Set Number Video Plus+ System SetupGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Won’t stop blinking Record Safety tab removed RecordingOther Problems Index Front ViewRear View Display Panel VCRRemote Control TV Muting Button mutes soundRemote Control LCD Fast Forward FF Button same as button onMaximum recording time DA4 Double Azimuth helical