JVC LPT0319-001A, HR-S8700EK Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 68

60SUBSIDIARYSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

IMPORTANT

Perform the following steps only if —

—Video Channel Set has not been done correctly by the Auto Set Up function (☞ pg. 8).

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.

●If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection), or via the provided RF cable, an S-Video cable and an audio cable (S-VIDEO connection), you do not need the video channel so you have to set the video channel to off. — Go to "With AV or S-VIDEO Connection" below.

●If you have connected the video recorder to your TV via the provided RF cable only (RF connection), you have to set the correct video channel — Go to "With RF Connection" on page 61.

1

2

1

2

– –:– –

1 2 3

4

5

6

7 8 9

0

3

4

4

3

OK

PR

With AV or S-VIDEO

Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■batteries have been installed in the remote control.

ACCESS VIDEO CHANNEL SET MODE

		Press and hold down STOP on the recorder until the
	1 display panel shows the following.
	2	SET VIDEO CHANNEL
	2	Press PR – until the display panel shows "–OUT– –".
		Press PR – until the display panel shows "–OUT– –".

●Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this.

Image 68

Contents HR-S8700EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder Connect Video Recorder to TVBack of TV Mains outlet Mains Power Cord Video ConnectionBefore performing the following procedure, make sure that With the AV or S-VIDEO connectionTion pg and the TV is turned on, Go to itemRemote control while downloading is 10 or If -- appears on the display panel, referLink screen will appear. Then the Guide Program number setIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedAccess Main Menu Screen Access Mode SET ScreenLink Functions Turn on the RecorderSatellite Receiver Control Setting Select Satellite RECEIVER’S Channel for Testing Enter Satellite RECEIVER’S BrandCheck Result of Test CodePlayback Load a CassetteFind Programme Start Point Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Enter ProgrammeStart Time TimeSET PDC Mode Timer ModeSET Tape Speed Return to NormalCheck, Cancel And Replace Programmes When programmes overlap each other Cancel or Change Programme SettingConfirm Overlapping Programmes ModifyNavigation Check Memory Return to Normal ScreenTurn OFF Navigation Turn Off NavigationAccess Find Blank Space Screen Title EditingSelect Tape Number Load a CassetteAccess Video Navigation Screen Enter CharacterEdit Tape Title Select Tape NumberEdit Programme Title Category Select ProgrammeSelect Category Delete Programme DataDelete Tape Data Delete Programme DataAccess Find Title Screen Access Tape NO. ScreenAccess Video Finding TitleAccess Date Screen Select Programme Access Category ScreenSelect Programme Load a Cassette Sorting By DateNavigation Check Memory Title Editing Access Main Menu Screen Select Programme Return to Normal Screen Finding Title Access Date Screen Playback Picture Adjustment Adjust TrackingOverride Automatic Tracking ManuallySET Mode ModeDigital 3R Video StabilizerAccess REC Level Adjust AudioSelecting Sound You Want Control ScreenReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionDuring Playback Type of Broadcast On-screen Display Being ReceivedLooking For Scene You Want Activate Index SearchSkip Over Unwanted SectionsSuper VHS S-VHS VHS ET and VHS Select S-VHS ModeRecording According To Tape Type S.T. Picture System Select B.E.S.T. ModePlayback/ Recording According To Tape Charac- teristics Start Playback RecordingPlayback During B.E.S.TConnector TV Aerial cable Audio in connector Automatic Satellite Programme RecordingSatellite Receiver Unit AerialAccess Main Menu Screen Select L-2 Select ModeREC Mode ScreenRemote Control Functions Remove Power SupplySET Remote Control Code RE-SUPPLY PowerControl Your TV Using Additional Buttons TV Multi-Brand Remote ControlSET TV Brand Code Operate TVSatellite Receiver Multi Brand Remote Control Brand CodeOperate Satellite Receiver NumberAccess Main Menu Access Mode SETControl SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Press Synchro /8again Repeat steps 4 6 as necessary Synchro Edit connector Lanc Cable not providedSynchro Editing Input Mode SET Edit ModeEdit To Or From Another Video Recorder SET Recording DECK’SRecorder Player OUTPUT/INPUT Setting SELECT/INPUT SettingAudio Dubbing Locate END Point Reset the CounterInsert Editing Engage Insert Editing Start EditingEND Insert Editing Press InsertTerminal JLIPJoint Level Interface Protocol Connector Access Initial SET ScreenAccess Jlip ID NO. SET Screen Information On J TerminalENABLE/DISABLE Other FunctionsON-SCREEN Display On-Screen DisplayPress %Þ to move the highlight bar pointer to Select Power Save ModePower Save Mode Access Mode SET Screen Auto TimerAuto SP→LP Timer Next Function MemoryResume Recording Engage RECORD-PAUSE ModeStop Playback Connection To Stereo System Speaker TelevisionAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelTest Signal With RF ConnectionTuner Set Perform Auto Channel SETAuto Channel Set Pointer to Auto CHView Confirmation Screen Storing Channels Manually Input ChannelEnter NEW Channel Information Close Confirmation ScreenWhen Receiving a Scrambled Broadcast Change Station Preset PositionFine-Tuning Channels Already Stored Delete a ChannelEnter NEW Character TV Station And ID List Station NameTV Station Channel Number Guide Clock Set Guide Program Number Set Video Plus+ System SetupNumber What happens if the tape runs out during recording? Questions And AnswersÄ remain lit on the display panel. Is there Problem? Troubleshooting Won’t stop blinking Record Safety tab removed RecordingOther Problems Index Front ViewRear View Display Panel VCRRemote Control TV Muting Button mutes soundRemote Control LCD Fast Forward FF Button same as button onMaximum recording time DA4 Double Azimuth helical