JVC LPT0002-027B Oubleshooting, Camcorder recording is not Camcorder has not been, Timer again

Page 52

52EN

TROUBLESHOOTING(cont.)

4. Camcorder recording is not	● The camcorder has not been	Confirm that the camcorder is
possible.	properly connected.	properly connected.
	● The input mode is not correct.	Set the input mode to “AU”.

TIMER RECORDING

	SYMPTOM		POSSIBLE CAUSE		CORRECTIVE ACTION
1.	Timer recording won’t work.		● The clock and/or the timer have		Re-perform the clock and/or timer
			been set incorrectly.		settings.
			● The timer is not engaged.		Press TIMER and confirm that “ä“ is
					displayed on the display panel.

2.	On-screen timer programming is		● Timer recording is in progress.		Timer programming can’t be
	not possible.				performed while a timer recording is
					in progress. Wait until it finishes.

3.	“ä“ and “]“ on the display		● The timer is engaged but there’s no		Load a cassette with the Record
	panel won’t stop blinking.		cassette loaded.		Safety tab intact, or cover the hole
					using adhesive tape.

4.	The cassette is automatically		● The loaded cassette has had its		Remove the cassette and cover the
	ejected, and “ä“ and “]“ on the		Record Safety tab removed.		hole with adhesive tape, or insert a
	display panel won’t stop blinking.				cassette with the Record Safety tab
					intact.

5.	“ä“ blinks for 10 seconds and the		● TIMER has been pressed when there		Check the programmed data and re-
	Timer mode is disengaged.		are no programs in memory, or the		program as necessary, then press
			timer record information has been		TIMER again.
			programmed incorrectly.

6.	The cassette is automatically		● The end of the tape was reached		The programme may not have been
	ejected, the power shuts off and		during timer recording.		recorded in its entirety. Next time
	“ä“ and “]“ won’t stop				make sure you have enough time on
	blinking.				the tape to record the entire
					programme.

7.	SHOWVIEW does not timer-record		● The recorder’s channel positions		Refer to "Guide Program Number Set"
	properly.		have been set incorrectly.		and re-perform the procedure
					(☞ pg. 10).

OTHER PROBLEMS

	SYMPTOM		POSSIBLE CAUSE		CORRECTIVE ACTION
1.	Whistling or howling is heard from		● The camcorder’s microphone is too		Position the camcorder so its
	the TV during camcorder record-		close to the TV.		microphone is away from the TV.
	ing.		● The TV’s volume is too high.		Turn the TV’s volume down.

2.	When scanning channels, some of		● Those channels have been desig-		If you need the skipped channels,
	them are skipped over.		nated to be skipped.		restore them (☞ pg. 46).

3.	The channel cannot be changed.		● Recording is in progress.		Press PAUSE to pause the recording,
					change channels, then press PLAY to
					resume recording.

4.	The remote control won’t operate		● The TV/SAT./VCR switch is in the		Set the switch to the correct position.
	the TV or satellite tuner.		wrong position.

5.	Channel settings that were made		● After the manual settings were		Perform manual setting again.
	manually seem to have changed or		made, Auto Channel Set was
	disappeared.		performed.

6.	No channels are stored in the		● The TV aerial cable was not		Connect the TV aerial cable to the
	recorder's memory.		connected to the recorder when		recorder properly and turn off the
			Auto Set Up was performed.		recorder power once, then turn the
					recorder power back on again. The
					recorder will try Auto Set Up again
					(☞ pg. 4).

Image 52

Contents HR-DD949E/EH For Italy Safety PrecautionsDo not place the recorder Installing Your NEW Record ER EN Basic ConnectionsAuto Set Up Turn on the RecorderSelect Country Nitial Sett IngsPerform Auto SET UP Select LanguageIf you are referring to the on-screen display Language Code for the HR-DD949EInitial Settings If both auto channel set and auto clock set have failedLanguage for the on-screen display Just ClockLanguage Access Video Channel SET Mode Exit Video Channel SET ModeEN Initial Settings Video Channel SetAccess Video Channel SET ModeMode With AV ConnectionMake List of Stored Station Names Channel Positions SetupGuide Program Number Set When Using a Satellite Tuner Enter ShowviewNumber Confirm Channel Position NumberBasic PlaybackFeatures PlaybackAdjust Tracking Override Automatic TrackingManually Return to AutomaticNtsc Playback Activate Instant ReviewInstant ReView Spatializer Activate SpatializerTrack USE SET A/B Code Switch RE-SUPPLY PowerActivate Scene Finder Stop Scene FinderAudio signal during TimeScan Time Scan IndicatorTimeScan Variable-Speed Search/ Reverse PlayTimeScan Speed SP Speed LP Audio outputAccess Main Menu Screen Access Mode SET ScreenSelect Mode Return to Normal ScreenBasic Recording Access Main Menu S.T. Picture SystemScreen Return to NormalPause Play Record On-Screen Displays ENABLE/DISABLE ON-SCREEN Display13 3 Recording Features Reset CounterSelect Channel to Watch SET Counter DisplayTo Record Stereo And Bilin- gual Programmes A2 Receiving Stereo And Bilin- gual ProgrammesType of Broadcast On-screen Display Being Received Engage ITR Mode Instant Timer Recording ITRSET Recording Duration Press Record on the recorderTimer Recording EN Timer RecordingWhen Using The Illumi-Guide Feature CancelSatellite Tuner Users Pressing PROG. CheckEN Timer RECORDINGcont Regular Timer ProgrammingStop +/-,DATE +/-,TV PROG. +/-,MENU Buttons remain lit Start +/-, Stop +/-, Date + TV PROG. +/- and MenuPress TV PROG. + PDC/VPSAccess Programme Auto TimerCheck And Cancel Programmes Revise ProgrammeTimer Auto SP/LP TimerTimer Warning Engage Auto SP/LPSET Recording DECK’S Input Mode Edit To Or From Another Video RecorderMake Connections Start Source PlayerPlayer Recorder PlayerEdit From a Camcorder SET RECORDER’S InputStart Camcorder Start RecorderSET Input Mode Locate Start PointEngage Audio Dubbing Start DubbingReset the Counter Locate END PointRecorder Your recorder Recorded tapeStart Editing Engage Insert EditingEND Insert Editing Access Jlip ID NO. SET Screen Interface Protocol ConnectorSET Jlip ID Number Terminal JLIPJoint LevelConnecting Using a Decoder Select Input ModeConnect Decoder SET TunerTV Multi Brand Remote Control Control Your TV Using Additional ButtonsSET TV Brand Code TRY Operating TVSatellite Tuner Multi SET Satellite Tuner Brand CodeTRY Operating Satellite Tuner Satellite Tuner Brand CodeAccess Country SET Tuner SETAuto Channel Set Press Push JOG toPress Push JOG Move the highlight bar Pointer to Language of yourTo initiate Auto Channel Set Appears,Select Item Delete ChannelClose Confirmation Select NEW PositionSwitch Stations Access Manual CH. SETPerform Tuning Select NEW StationTV Station And ID List Station NameClock SET PreparationMove the highlight bar pointer to Clock SET by Screen appearsSET Clock Automatically SET Date and TimeSET Just Clock Start Clock OperationTroubleshooting E N Oubleshooting Timer againCamcorder recording is not Camcorder has not been Ä remain lit on the display panel. Is there a problem? Questions and Answer S E NOpen the lid to access covered connectors and buttons IndexRear View How To Use Installing BatteriesEN Index Maximum recording time SpecificationsProvided in Australia and New Zealand only EMO Memo Auto Set Up completed International Telephone Country CodeLanguage Code for the HR-DD949E Language Code for the HR-DD949EH