JVC HR-VP68U Adjusting tracking condition, Selecting monitor sound, Automatic operations after

Page 23

EN 23

D Adjusting tracking condition

—Tracking Adjustments

Automatic tracking adjustment

This VCR automatically adjusts the tracking condition. Whenever you insert a tape and start playback, automatic tracking starts working and continuously analyzes the signal to enable optimum picture quality during playback.

Manual tracking adjustment

If automatic tracking cannot eliminate noises well during playback, use the manual tracking following the procedures below.

You can also use the manual tracking during slow motion playback ( pg. 29).

1 Activate manual tracking

Press CH 5 and ° on the front panel at the same time during playback.

2 Eliminate the noises on the TV screen.

Press CH 5 and ° (or CH + and – on the Remote). Press it briefly for a fine adjustment, or press and hold for coarse adjustment. Watch the screen and continue adjustment until optimum picture and sound quality are achieved.

3 Reactivate automatic tracking

Press CH 5 and ° on the front panel at the same time. The automatic tracking becomes active again. “AUTO PICTURE” will momentarily flash on the TV.

E Selecting monitor sound

— Audio Monitor

You can select the desired monitor sound.

While playing back a tape on which stereo sound or SAP sound is recorded, press A. MONITOR on the Remote. Each time you press the button, sound changes as follows:

 

 

HI-FI

 

 

 

HI-FI L

 

 

HI-FI R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NORM

 

 

 

 

NORM

 

 

 

HI-FI

 

 

 

 

 

 

 

 

 

HI-FI: Normally select this.

Hi-Fi sound is played back.

HI-FI L: Sound on the left Hi-Fi channel is played back.

HI-FI R: Sound on the right Hi-Fi channel is played back. NORM:Sound on the normal track is played back. NORM HI-FI:

Both sounds on the Hi-Fi track and normal track are mixed and played back.

Note:

The above indication appears when “SUPERIMPOSE” is set to “ON” ( pg. 39), though the monitor sound changes in sequence.

If the tape being played back has no Hi-Fi sound track, the normal sound track will be heard regardless of this setting.

If RF connection ( pg. 7) is used for viewing pictures on the TV, sound will be monaural even though you select “HI-FI”. You can also use the menu to select your desired monitor sound. ( pg. 41)

F Automatic operations after

rewinding — Next Function Memory

The Next Function Memory “tells” the VCR what to do after rewinding is complete.

Ensure that the VCR is in stop mode.

a– For Automatic Playback Start

Press REW ( 1 ), then press PLAY ( 3 ) within 2 seconds.

b– For Automatic Power Off

Press REW ( 1 ), then press POWER within 2 seconds.

c– For Automatic Timer Standby

Press REW ( 1 ), then press TIMER within 2 seconds.

NOTE:

It is not possible to select the Automatic Timer Standby function if the cassette’s record safety tab is removed.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents HR-VP68U Telephone Number Dear CustomerGrounding or Polarization Power SourcesPower Lines Power Cord ProtectionReplacement Parts AccessoriesDamage Requiring Service CleaningContents Coaxial cable Audio OUT not supplied AC Power CordBasic Connections Antenna or cableFinal preparation for use Check contentsSituate VCR Connect VCR to TVWhat to do if Plug & Play setting failed Plug & Play SettingPerform Plug & Play setup Select language Language SettingAccess Main Menu screen Access Initial Set screenSelect clock set Clock Setting10 EN PreparationsSelect time zone Setting clock semiautomaticallySet Auto Clock to on Select host channelManual Clock Set Setting clock manuallySelect D.S.T. mode 12 ENPerform Auto Channel Set Tuner SettingAccess Tuner Set screen Add or skip desired channels Setting channels manuallyAccess Manual Channel Set screen 14 ENConnect cable box to VCR Cable Box Control SettingSituate Controller Attach ControllerSelect cable box output channel Access Cable Box Set screen16 EN Turn on cable boxIf the cable boxs channel does not change to AccessPress OKCable. Box Brand Set screenEnter cable box brand DBS receiver Controller Your VCRsuggested Locations How to control the DBS receiver18 EN Connect DBS receiver to VCRSelect DBS receiver output channel Access DBS Receiver Set screenTurn on DBS receiver Enter DBS Receiver’s brand Access DBS Receiver Brand Set screen20 EN Start playback Basic PlaybackLoad a cassette Checking tape position Basic Playback Features22 EN Changing display informationAutomatic operations after Adjusting tracking conditionSelecting monitor sound Locating beginning Locating beginning of timerAccess distant code 24 ENStart recording Basic RecordingSelect recording channel Set tape speedWatching one program while recording another Basic Recording Features26 EN Specifying recording lengthOther useful functions for recording Showing on-screen displayDisplay VCR status on TV screen Erase on-screen displayRapidly Picture Search High-Speed Picture Search Special Effect Playback28 EN Locating particular scenePause during playback Viewing still pictureSkipping unwanted portions Viewing slow motion picture30 EN VCR Plus+ Timer ProgramingPress SP/EP Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Input receiving channel numberVCR Plus+ guide channel matching VCR Plus+ Setup32 EN Input guide channel number Access Guide Channel Set screen34 EN Express Timer ProgramingTo timer-record daily Monday-Friday or weekly serials 36 EN Checking program settingsOverlapping programs blink on the screen Confirm overlapping programsSelect program to modify Select Function Useful Function SettingsChange setting 38 ENWhen this function is set to OFF When this function is set to onFor Example 40 ENThis VCR This VCR for recording Edit From Camcorder42 EN ConnectionMake connections Select input mode on this VCRAccess Main Menu screen on this VCR Enable remote pause functionSelect Edit function Edit To Or From Another44 EN Load cassettesOperate TV TV Brand SettingTurn on the TV Set TV brand codeEnter cable box brand code Cable Box Brand Setting46 EN Turn on the cable boxOperate DBS receiver DBS Receiver Brand SettingTurn on the DBS receiver Enter DBS receiver brand code48 EN Changing Remote Control CodePower 50 EN Timer RecordingOther Problems What happens if the tape reaches its end during recording? 52 ENCan the VCR indefinitely remain in still mode? VCR PLUS+ List of termsFront display panel 54 ENFront panel On-screen display Rear panelRemote How to use the Remote56 EN Compact VHS* TC-20 ST-C20 TC-30 ST-C30 TC-40 ST-C40 Usable cassettesFull-Size VHS 30 ST-30 58 EN HOW to Locate Your JVC Service CenterLimited Warranty HR-VP68U
Top Page Image Contents