JVC HR-VP68U manual 50 EN, Timer Recording

50 EN				TROUBLESHOOTING (cont.)
	TIMER RECORDING
		SYMPTOM	POSSIBLE CAUSE			CORRECTIVE ACTION
	1.	Timer recording will not work.	The clock and/or the timer have		Set the clock and/or timer correctly.
			been set incorrectly.
			The timer is not engaged.		Press TIMER and check to make sure
					that ä appears on the front display
					panel.
			The VCR has not been set up properly.		Re-perform the set-up procedures.
					Make sure you have compensated for
					guide channel and VCR or cable box
					channel number mismatches
					(	pg. 32).
	2.	Timer programing will not work.	Timer recording is in progress.		Timer programing cannot be performed
					when timer recording is in progress.
					Wait until it finishes.
	3.	ä and ] on the front display	The timer is engaged but there is no		Load a cassette with the record safety
		panel will not stop blinking.	cassette loaded.		tab intact, or with the hole covered
					with adhesive tape.
	4.	The cassette is automatically	The loaded cassette has had its		Remove the cassette and cover its
		ejected, and ä and ] on the	record safety tab removed.		hole with adhesive tape, or replace it
		front display panel will not stop			with a cassette on which the safety
		blinking.			tab is intact.
	5.	ä blinks for 10 seconds and the	TIMER has been pressed when there		Check the programed data and set
		timer mode is disengaged.	are no programs in memory, or the		again if necessary, then press TIMER
			timer recording program has not		again.
			been set correctly.
	6.	The cassette is automatically	The tape reaches its end during		The program may not have been
		ejected, the power shuts off and ä	timer recording.		recorded in its entirety. Next time be
		and ] will not stop blinking.			sure you have enough time on the
					tape to record the entire broadcast.
	7.	Cable channels are not automatically	The Controller is not properly		Connect the Controller correctly
		switched during timer recording.	connected to the VCR.		(	pg. 15).
			The output channel selected in the		After confirming your cable box’s
			Cable Box Set screen is incorrect.		output channel number, re-access the
					Cable Box Set screen and select the
					correct number ( pg. 16).
			The cable box is turned off.		Make sure the power is on before
					timer recording starts.
	8.	Satellite channels are not	The Controller is not properly		Connect the Controller correctly
		automatically switched during timer	connected to the VCR.		(	pg. 18).
		recording.	The output channel selected in the		After confirming your DBS receiver’s
			DBS Receiver Set screen is incorrect.		output channel number, re-access the
					DBS Receiver Set screen and select
					the correct number ( pg. 19).
			The VCR is not set correctly to		Set the correct DBS receiver brand
			control the DBS receiver		code ( pg. 20).
			The DBS receiver is turned off.		Make sure the power is on before
					timer recording starts.
	9.	Timer recording begins as	Even though you do not use an		Set “CABLE BOX SET” to “OFF” (
		scheduled, but the channel is	external cable box or DBS receiver,		pg. 16) or “DBS RECEIVER SET” is set
		always incorrect.	“CABLE BOX SET” is set to “ON” or		to “OFF” (		pg. 19).
			“DBS RECEIVER SET” is set to “ON”.
	10.You moved, and now VCR Plus+		The receivable stations in the new		Re-perform the VCR Plus+ setup
		does not work properly.	area are received on different		procedure (		pg. 32).
			channels than those in the previous
			area.
	11.	“PROGRAM FULL” is displayed on	All 8 programs of the VCR’s timer		Wait until a space in memory clears,
		the screen.	memory are used.		or cancel unnecessary program
					information (		pg. 36).

CONTINUED ON NEXT PAGE \