JVC HR-VP68U manual TV Brand Setting, Turn on the TV, Set TV brand code, Operate TV

Page 45

MULTI-BRAND REMOTE CONTROL

EN 45

TV Brand

Setting

This Remote can control some functions of remote controllable TVs listed below. Without setting, you can control a JVC TV.

1 Turn on the TV

Turn on the TV using the Power button on the TV or its Remote.

2–14

TV

TV/VCR

4

7

1

			2–2
			POWER
2	3
5	6	2	2–3
8	9		Number
0		4

2Set TV brand code

Follow the example shown below.

1Press and hold TV.

2 Press MBR SET.

3 Press the Number keys to enter your TV’s brand code by referring to the table below.

4 Press OK, and release TV.

The TV should turn off. If it does, try other

operations below ( step 3).

Once you have set the Remote to operate the TV, you do not have to set it until you replace the batteries from the Remote.

PANASONIC has two codes. If the TV does not function with one code, try entering the other.

3Operate TV

While holding down TV, press one of the following buttons: POWER, TV/VCR, TV CH +/–,

3

2–4

ENTER

TV VOL +/–

TV CH +/–

TV/VCR, (TV Muting), TV VOL +/–, and Number keys.

For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

NOTES:

Depending on the type of TV, some or all functions cannot be operated using this Remote.

It’s not possible to operate a TV not equipped with a remote sensor.

TV BRAND NAME	BRAND CODE
JVC	01, 03
HITACHI	10
MAGNAVOX	02
MITSUBISHI	03
PANASONIC	04, 11
RCA	05
SHARP	06
SONY	07
SAMSUNG	12
SANYO	13
SEARS	13
TOSHIBA	08
ZENITH	09

(Ex.) To set Remote to RCA 05:

	MBR SET
TV	A/B
			E
	0	5	NTER/O
			3	SD
			3	OK
Hold	Press in succession
down

Release

Image 45

Contents HR-VP68U Telephone Number Dear CustomerPower Lines Power SourcesPower Cord Protection Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsContents Basic Connections Audio OUT not supplied AC Power CordAntenna or cable Coaxial cableSituate VCR Check contentsConnect VCR to TV Final preparation for usePlug & Play Setting Perform Plug & Play setupWhat to do if Plug & Play setting failed Access Main Menu screen Language SettingAccess Initial Set screen Select language10 EN Clock SettingPreparations Select clock setSet Auto Clock to on Setting clock semiautomaticallySelect host channel Select time zoneSelect D.S.T. mode Setting clock manually12 EN Manual Clock SetTuner Setting Access Tuner Set screenPerform Auto Channel Set Access Manual Channel Set screen Setting channels manually14 EN Add or skip desired channelsSituate Controller Cable Box Control SettingAttach Controller Connect cable box to VCR16 EN Access Cable Box Set screenTurn on cable box Select cable box output channelAccessPress OKCable. Box Brand Set screen Enter cable box brandIf the cable boxs channel does not change to 18 EN How to control the DBS receiverConnect DBS receiver to VCR DBS receiver Controller Your VCRsuggested LocationsAccess DBS Receiver Set screen Turn on DBS receiverSelect DBS receiver output channel Access DBS Receiver Brand Set screen 20 ENEnter DBS Receiver’s brand Basic Playback Load a cassetteStart playback 22 EN Basic Playback FeaturesChanging display information Checking tape positionAdjusting tracking condition Selecting monitor soundAutomatic operations after Access distant code Locating beginning of timer24 EN Locating beginningSelect recording channel Basic RecordingSet tape speed Start recording26 EN Basic Recording FeaturesSpecifying recording length Watching one program while recording anotherDisplay VCR status on TV screen Showing on-screen displayErase on-screen display Other useful functions for recording28 EN Special Effect PlaybackLocating particular scene Rapidly Picture Search High-Speed Picture SearchSkipping unwanted portions Viewing still pictureViewing slow motion picture Pause during playback30 EN VCR Plus+ Timer ProgramingTo use the VCR while it is in timer recording standby mode Engage timer recording standby modeInput receiving channel number Press SP/EPVCR Plus+ Setup 32 ENVCR Plus+ guide channel matching Input guide channel number Access Guide Channel Set screen34 EN Express Timer ProgramingTo timer-record daily Monday-Friday or weekly serials 36 EN Checking program settingsConfirm overlapping programs Select program to modifyOverlapping programs blink on the screen Change setting Useful Function Settings38 EN Select FunctionWhen this function is set to OFF When this function is set to onFor Example 40 ENThis VCR 42 EN Edit From CamcorderConnection This VCR for recordingAccess Main Menu screen on this VCR Select input mode on this VCREnable remote pause function Make connections44 EN Edit To Or From AnotherLoad cassettes Select Edit functionTurn on the TV TV Brand SettingSet TV brand code Operate TV46 EN Cable Box Brand SettingTurn on the cable box Enter cable box brand codeTurn on the DBS receiver DBS Receiver Brand SettingEnter DBS receiver brand code Operate DBS receiver48 EN Changing Remote Control CodePower 50 EN Timer RecordingOther Problems 52 EN Can the VCR indefinitely remain in still mode?What happens if the tape reaches its end during recording? VCR PLUS+ List of terms54 EN Front panelFront display panel On-screen display Rear panelHow to use the Remote 56 ENRemote Usable cassettes Full-Size VHS 30 ST-30Compact VHS* TC-20 ST-C20 TC-30 ST-C30 TC-40 ST-C40 58 EN HOW to Locate Your JVC Service CenterLimited Warranty HR-VP68U