JVC HR-VP68U DBS Receiver Brand Setting, Turn on the DBS receiver, Enter DBS receiver brand code

Page 47

DBS Receiver Brand Setting

EN 47

This Remote can control some functions of the DBS (Direct Broadcast Satellite) receivers listed below.

1 Turn on the DBS receiver

Turn on the DBS receiver using the Power button on the DBS receiver or its Remote.

2Enter DBS receiver brand code

Follow the example shown below.

2–14

CABLE/DBS 1

4

7

1

2

5

8

0

3

POWER

2–2

3

 

2

2–3

6

 

 

 

9Number

4

2–4

ENTER

1Press and hold CABLE/DBS.

2 Press MBR SET.

3 Press the Number keys to enter your DBS receiver’s brand code by referring to the table below.

4 Press OK, and release CABLE/DBS.

The DBS receiver should turn off. If it does, try other operations below ( step 3).

Once you have set the Remote to operate the DBS receiver, you do not have to set it until you replace the batteries from the Remote.

3 Operate DBS receiver

While holding down CABLE/DBS, press one of the following buttons: POWER, TV CH +/–, and Number keys.

For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

To change the DBS receiver’s channels, press TV CH +/– or the Number keys. (The CH +/– button can be used to change the VCR’s

TV CH +/–

channels only.)

DBS BRAND NAME

BRAND CODE

 

 

JVC (DISH Network)

51

ECHOSTAR (DISH Network)

51

PRIMESTAR

50

SONY (DSS)

41

RCA (DSS)

40

 

 

NOTES:

Depending on the type of DBS receiver, some or all functions cannot be operated using this Remote.

It’s not possible to operate a DBS receiver not equipped with a remote sensor.

It's not possible to set the Remote for both your DBS receiver and a cable box at the same time. You can only set the Remote to operate one of these units at a time.

(Ex.) To set the Remote to JVC 51:

CABLE/

MBR SET

 

 

 

 

 

DBS

A/B

 

 

 

 

 

 

 

 

E

 

 

 

 

5

1

NTER/O

SD

Release

 

3

OK

Hold

Press in succession

 

 

 

down

 

 

 

 

 

 

Image 47
Contents HR-VP68U Telephone Number Dear CustomerGrounding or Polarization Power SourcesPower Lines Power Cord ProtectionReplacement Parts AccessoriesDamage Requiring Service CleaningContents Coaxial cable Audio OUT not supplied AC Power CordBasic Connections Antenna or cableFinal preparation for use Check contentsSituate VCR Connect VCR to TVWhat to do if Plug & Play setting failed Plug & Play SettingPerform Plug & Play setup Select language Language SettingAccess Main Menu screen Access Initial Set screenSelect clock set Clock Setting10 EN PreparationsSelect time zone Setting clock semiautomaticallySet Auto Clock to on Select host channelManual Clock Set Setting clock manuallySelect D.S.T. mode 12 ENPerform Auto Channel Set Tuner SettingAccess Tuner Set screen Add or skip desired channels Setting channels manuallyAccess Manual Channel Set screen 14 ENConnect cable box to VCR Cable Box Control SettingSituate Controller Attach ControllerSelect cable box output channel Access Cable Box Set screen16 EN Turn on cable boxIf the cable boxs channel does not change to AccessPress OKCable. Box Brand Set screenEnter cable box brand DBS receiver Controller Your VCRsuggested Locations How to control the DBS receiver18 EN Connect DBS receiver to VCRSelect DBS receiver output channel Access DBS Receiver Set screenTurn on DBS receiver Enter DBS Receiver’s brand Access DBS Receiver Brand Set screen20 EN Start playback Basic PlaybackLoad a cassette Checking tape position Basic Playback Features22 EN Changing display informationAutomatic operations after Adjusting tracking conditionSelecting monitor sound Locating beginning Locating beginning of timerAccess distant code 24 ENStart recording Basic RecordingSelect recording channel Set tape speedWatching one program while recording another Basic Recording Features26 EN Specifying recording lengthOther useful functions for recording Showing on-screen displayDisplay VCR status on TV screen Erase on-screen displayRapidly Picture Search High-Speed Picture Search Special Effect Playback28 EN Locating particular scenePause during playback Viewing still pictureSkipping unwanted portions Viewing slow motion picture30 EN VCR Plus+ Timer ProgramingPress SP/EP Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Input receiving channel numberVCR Plus+ guide channel matching VCR Plus+ Setup32 EN Input guide channel number Access Guide Channel Set screen34 EN Express Timer ProgramingTo timer-record daily Monday-Friday or weekly serials 36 EN Checking program settingsOverlapping programs blink on the screen Confirm overlapping programsSelect program to modify Select Function Useful Function SettingsChange setting 38 ENWhen this function is set to OFF When this function is set to onFor Example 40 ENThis VCR This VCR for recording Edit From Camcorder42 EN ConnectionMake connections Select input mode on this VCRAccess Main Menu screen on this VCR Enable remote pause functionSelect Edit function Edit To Or From Another44 EN Load cassettesOperate TV TV Brand SettingTurn on the TV Set TV brand codeEnter cable box brand code Cable Box Brand Setting46 EN Turn on the cable boxOperate DBS receiver DBS Receiver Brand SettingTurn on the DBS receiver Enter DBS receiver brand code48 EN Changing Remote Control CodePower 50 EN Timer RecordingOther Problems What happens if the tape reaches its end during recording? 52 ENCan the VCR indefinitely remain in still mode? VCR PLUS+ List of termsFront display panel 54 ENFront panel On-screen display Rear panelRemote How to use the Remote56 EN Compact VHS* TC-20 ST-C20 TC-30 ST-C30 TC-40 ST-C40 Usable cassettesFull-Size VHS 30 ST-30 58 EN HOW to Locate Your JVC Service CenterLimited Warranty HR-VP68U