JVC HR-J682EK, HR-J680EK manual Advanced features

Page 40

40

advanced features

programme satellite receiver Enter the details of the programme into your satellite receiver (see receiver manual) and put a tape in the VCR.

get to the mode set screen Press m. Move the highlight bar to MODE SET using the Aand Bbuttons and press O(or E).

select l-2 select mode Move the highlight bar to L-2 SELECT using the Aand B buttons. Press O(or E) to select L-2or SAT. Then press m.

set tape speed Press /on the Remote Control to set the tape speed to either SP or LP.

engage vcr in auto mode Press and hold SATcon the VCR for about 2 seconds. The SATc indicator on the VCR display panel lights up and the VCR turns off automatically. Any signal detected at the AV2 (L-2) IN/DECODER connecter will automatically start the VCR recording; when the signal stops, so will the VCR.

Notes

connectors Auto Satellite Prog Recording is only possible using the AV2 (L-2) IN/DECODER connector.

timer mode You cannot put the VCR into TIMER MODE when using Auto Satellite Prog Recording Mode.

rThe number of programmes recorded will not be displayed on the VCR display panel when the rbutton is pressed.

timer recording Auto Satellite Prog Recording is not possible if your satellite receiver does not have a timer.

indicator The SATcindicator light flashes when Auto Satellite Prog Recording is in progress.

disengage To disengage the VCR during Auto Satellite Prog Recording, press the obutton. The VCR will stop recording and turns off.

tape speed When recording two or more programmes consecutively, you cannot set a different tape speed for each programme. The first speed selected will apply to all programmes in that recording session.

b.e.s.t. The B.E.S.T. system will not work during Auto Satellite Prog Recording.

just clock Just Clock does not work when in Auto Satellite Prog Recording mode.

incoming signal The VCR will only react to the start of an incoming signal at the AV2 (L-2) IN/DECODER connecter. If you try to engage Auto Satellite Prog Recording Mode whilst the satellite receiver is powered on, the SATcindicator light will flash but the VCR will not record. You must power the satellite receiver off then on again to begin recording in these circumstances.

cable input You can record in the same way from a cable system as long as you connect the cable system has a timer on/off function and is connected to the AV2 (L-2) IN/DECODER.

incompatibilities Some satellite receivers output signals even when turned off. These receiv- ers cannot be used with this VCR in this way.

Page 39 Page 41
Image 40
Page 39 Page 41
Contents HR-J680EK HR-J682EK Safety Precautions If in doubt Ñ consult a competent electricianMoisture Condensation Some DoÕs And DonÕts On The Safe Use Of EquipmentContents Rear panel Diagram Key Front PanelWelcome to JVC Getting Everything ReadyPerform Auto Setup pg Auto Setup Three-Step Quick StartPreset Download Three step quick startCheck the Results Finish OffBasic Features Playback Load a Video CassettePlay Stop & EjectVideo Heads Cleaning Rewind and Fast ForwardPause During Playback Playback FeaturesSingle Frame Movement Variable Speed Search Slow MotionHigh Speed Search Recording Choose a ProgrammeSet the Tape Speed Start RecordingDisplay Tape Remaining Time Resetting the CounterChange Display Information Instant Timer Recording Recording Resume FunctionGet to the Video Plus + Screen Enter the PlusCode NumberPress O. The Video Plus+ Program screen Engage Timer Mode Return to Normal ScreenGet to the Programme Screen Express Timer ProgrammingEnter Programme Details AUX Check, Cancel & Change Programmes Press c, then press oto disengage the timer modeWhen Programmes Overlap Each Other Basic features Advanced Features Manual Tracking Picture QualityPicture Control Recording and Playback Using B.E.S.T Avoiding B.E.S.T. Time DelayB.E.S.T PictureÊSystem Turning B.E.S.T. on or OFFNicam Stereo and Bilingual Broadcasts Sound ModesSoundtrack Selection Finding Specific Scenes Skip SearchIndex Search Instant ReViewTV Auto Power On Link FunctionsNexTView Link VCR Auto StandbyDirect Rec Satellite Receiver Control Settings Installing Satellite ControllerSetting satellite receiverÕs brand CodeCheck Result of Test Auto Satellite Auto Record from Satellite ReceiverAdvanced features Select Setting EditingEditing Using Another VCR Set edit mode See Picture Control on pageÊ30Editing from a Camcorder Start recorder Press TOther Functions On-Screen Display O.S.DPower Save Mode Auto SP aLP TimerRepeat Playback Auto TimerNext Function Memory Connection to a Stereo System Stereo AmplifierAccess Video Channel Mode Exit Video Channel Set ModeVideo Channel Set Set Video ChannelAuto Channel Setup Tuner SetManual Channel Setup Change Station Name Delete a ChannelChange Station Preset Position Fine-Tuning Stored Channels TV Station ID GuideTV Station Channel Number Guide BBC1 BBC2 ITV CH4 CH5Setting the Clock Clock SetManually Setting Guide Program Numbers Guide Program NumbersQuestion and Answers PlaybackTroubleshooting Symptom Possible CauseRecording Other Problems List of Terms Memo Memo HR-J680/682EK
Top Page Image Contents