JVC HR-J680EK, HR-J682EK manual Recording

Page 59

subsidiary information

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

59

RECORDING

1.Recording cannot be started.

2.TV broadcasts cannot be recorded.

3.Tape-to-tape editing is not possible.

4.Camcorder recording is not possible.

¥There is no cassette loaded, or the cassette loaded has had its record safety tab removed.

¥L-1, L-2 or SAT has been selected as the input mode.

¥The source (another VCR, camcorder) has not been properly connected.

¥All necessary power switches have not been turned on.

¥The input mode is not correct.

¥The camcorder has not been properly connected.

¥The input mode is not correct.

Insert a cassette, or using adhesive tape, cover the hole where the tab was removed.

Set to the desired preset.

Confirm that the source is prop- erly connected.

Confirm that all unitsÕ power switches are turned on.

Set the input mode to L-1 or L-2.

Confirm that the camcorder is properly connected.

Set the input mode to L-1 or L-2.

TIMER RECORDING

1.Timer recording wonÕt work.

2.Timer programming is not possible.

¥The clock and/or the timer have been set incorrectly.

¥The timer is not engaged.

¥Timer recording is in progress.

Re-perform the clock and/or timer settings.

Press cand confirm that cis displayed on the display panel.

Timer programming canÕt be performed while a timer recording is in progress. Wait until it finishes.

3.con the display panel wonÕt stop blinking.

4.c, Uand ,on the display panel wonÕt stop blinking.

¥The timer is engaged but thereÕs no cassette loaded.

¥The loaded cassette has had its record safety tab removed.

¥The end of the tape was reached during timer recording.

Load a cassette with the record safety tab intact.

Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact.

The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

5.cblinks for 10 seconds and the Timer mode is disengaged.

¥chas been pressed when there are no programs in memory, or the timer record information has been pro- grammed incorrectly.

Check the programmed data and re-programme as necessary, then press cagain.

6.The VIDEO Plus+ system does not timer record properly.

¥The VCRÕs preset positions have been set incorrectly.

Refer to Guide Program Numbers (☞ pg. 56) and re-perform the procedure.

Page 58 Page 60
Image 59
Page 58 Page 60
Contents HR-J680EK HR-J682EK If in doubt Ñ consult a competent electrician Safety PrecautionsMoisture Condensation On The Safe Use Of Equipment Some DoÕs And DonÕtsContents Rear panel Front Panel Diagram KeyGetting Everything Ready Welcome to JVCPerform Auto Setup pg Three-Step Quick Start Auto SetupThree step quick start Preset DownloadFinish Off Check the ResultsBasic Features Stop & Eject PlaybackLoad a Video Cassette PlayRewind and Fast Forward Video Heads CleaningSingle Frame Movement Playback FeaturesPause During Playback High Speed Search Slow MotionVariable Speed Search Start Recording RecordingChoose a Programme Set the Tape SpeedChange Display Information Resetting the CounterDisplay Tape Remaining Time Recording Resume Function Instant Timer RecordingEnter the PlusCode Number Get to the Video Plus + ScreenPress O. The Video Plus+ Program screen Return to Normal Screen Engage Timer ModeEnter Programme Details Express Timer ProgrammingGet to the Programme Screen AUX Press c, then press oto disengage the timer mode Check, Cancel & Change ProgrammesWhen Programmes Overlap Each Other Basic features Advanced Features Picture Control Picture QualityManual Tracking Turning B.E.S.T. on or OFF Recording and Playback Using B.E.S.TAvoiding B.E.S.T. Time Delay B.E.S.T PictureÊSystemSoundtrack Selection Sound ModesNicam Stereo and Bilingual Broadcasts Instant ReView Finding Specific ScenesSkip Search Index SearchVCR Auto Standby TV Auto Power OnLink Functions NexTView LinkDirect Rec Installing Satellite Controller Satellite Receiver Control SettingsCode Setting satellite receiverÕs brandCheck Result of Test Auto Record from Satellite Receiver Auto SatelliteAdvanced features Editing Select SettingSet edit mode See Picture Control on pageÊ30 Editing Using Another VCRStart recorder Press T Editing from a CamcorderOn-Screen Display O.S.D Other FunctionsAuto SP aLP Timer Power Save ModeNext Function Memory Auto TimerRepeat Playback Stereo Amplifier Connection to a Stereo SystemSet Video Channel Access Video Channel ModeExit Video Channel Set Mode Video Channel SetTuner Set Auto Channel SetupManual Channel Setup Delete a Channel Change Station NameChange Station Preset Position TV Station ID Guide Fine-Tuning Stored ChannelsBBC1 BBC2 ITV CH4 CH5 TV Station Channel Number GuideClock Set Setting the ClockGuide Program Numbers Manually Setting Guide Program NumbersPlayback Question and AnswersSymptom Possible Cause TroubleshootingRecording Other Problems List of Terms Memo Memo HR-J680/682EK
Top Page Image Contents