JVC HR-J758E/EH TimeScan Audio, Speed SP Speed LP Audio output, HR-DD858EHR-DD858EH

EN19

TimeScan

Names of special-effects playback

Speed SP

Speed LP

Audio output

Reverse

Forward

Search

Play

Slow-Motion

*Still

Slow-Motion

Play

Search

-9x

-7x

-5x

-3x

-1x

-1/6x

-1/18x

0

1/18x

1/6x

1x

2x

3x

5x

7x

9x

-7x

-3x

-1/6x

-1/18x

0

1/18x

1/6x

1x

2x

5x

9x

Audio is output.

Audio is not

Audio is

Audio is not

Audio is output.

output.

output.

output.

* Still mode cannot be engaged using the remote control's % or %button. Still mode can be engaged by pressing the PAUSE button.

●The speed is shown during TimeScan in the upper right corner of the TV screen for approx. 5 seconds. (The display may be distorted.)

●To resume normal playback, press PLAY.

●When using the recorder's TIME SCAN SHUTTLE ring, the playback speed may not change in the correct step if it is turned too fast.

●Picture and audio may become distorted when the recording speed changes. When this happens, resume normal playback once, and then try using TimeScan again.

●The picture may be noisy or there may be a loss of colour when you change the playback speed. (More noise will appear with LP recordings.)

●Noise may appear or the upper part of the picture may be distorted during still, frame-by-frame playback, 2x search of LP recordings, or depending on the tape being used.

●Picture may appear distorted in comparison to normal playback.

●In TimeScan mode there will be a time lag between the video and the audio and noise may appear in the audio signal.

●TimeScan sound quality will differ in comparison to normal playback.

●When material such as music videos where there is non-stop sound (very few breaks in the soundtrack) are viewed at 2x normal speed, the audio playback may be faster than normal.

●When the playback direction is reversed, it takes approximately 6 seconds until sound is heard.

●Picture will be monochrome with an LP-recorded MESECAM tape during TimeScan.

●When playing back an NTSC tape, the speeds differ from those listed above and are not shown on the TV screen.

Also, depending on the type of tape being used, the picture may be distorted and there may be a loss of colour even when in the TimeScan mode.

If you don't want to hear TimeScan audio, set "TIME SCAN AUDIO" to "OFF" (See below).

TimeScan Audio

The audio output can be set ON/OFF during TimeScan. Select ON/OFF as required.

* The default setting is "ON".

1Press MENU to access the Main Menu screen.

2Move the highlight bar (pointer) to "MODE SET" by

pressing %Þ, then press OK or %.

3Move the highlight bar (pointer) to "TIME SCAN

AUDIO" by pressing %Þ, then press OK or	%to select
"ON" or "OFF".
4 Press MENU to return to the normal screen.

HR-DD858EHR-DD858EH

MODE SET		MODE SET
		AUTO TIMER	OFF
AUTO TIMER	OFF
O. S. D.	ON	O. S. D.	ON
B. E. S. T.	ON	B. E. S. T.	ON
AUTO SP=LP TIMER	OFF	AUTO SP=LP TIMER	OFF
POWER SAVE	OFF	AV2 SELECT	AV2
AV2 SELECT	AV2	COLOUR SYSTEM PAL/NTSC
COLOUR SYSTEM PAL/NTSC		TIME SCAN AUDIO	ON
NEXT PAGE
[5°] =		[5°] =
[MENU] : EXIT		[MENU] : EXIT
PREVIOUS PAGE
TIME SCAN AUDIO	ON

[5°] = [MENU] : EXIT