JVC HR-DD858E/EH, HR-J758E/EH Connecting Using a Stereo System, AUX in or Tape Monitor

Page 44

44ENSYSTEMCONNECTIONS(cont.)

Connecting/

Using A Stereo

System

FM Tuner

CD Player

Stereo Amplifier

These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo.

I

I

I

I

I

I

I

I

I

I

I

I

Speaker

Television

I I	I I	I	I	I	I I
I I					I I	I	II

I

III	AUX IN or TAPE MONITOR
I
II
I
I
I

I

Audio Cable (not provided)

Speaker

Mains outlet

ANT. IN

AV1 IN/OUT

R

L

AUDIO OUT

RF OUT

AV2 IN/DECODER

PAUSE

MAKE CONNECTIONS

1 Connect the AUDIO OUT L and R connectors on your video recorder to the AUX IN or TAPE MONITOR terminals on your stereo system’s receiver or amplifier.

NOTES:

●When connecting your recorder’s audio output connectors to a stereo amplifier, make sure you connect L and R correctly.

●If stereo or bilingual TV broadcasts are receivable in your area, this recorder can record them independently of the TV set and play them back through the connected stereo system.

●When listening to sound through the connected stereo system, turn the TV’s volume down completely.

Rear View

AUDIO OUT

CAUTIONS:

●This recorder has a dynamic range of more than 80 dB with regards to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them.

●Some speakers and televisions are specially shielded to prevent television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the video playback picture.

Image 44

Contents HR-DD858E/EH HR-J758E/EH Do not place the recorder Safety PrecautionsFor Italy Check Contents Basic ConnectionsSituate Recorder Connect Recorder to MainsAuto Set Up If you are referring to the front display panelIf you are referring to the on-screen display International Telephone Country CodeLanguage Code Via an RF cable only RF connectionVideo Channel Your TV to the Video Channel. Refer toIf both auto channel set and auto clock set have failed Language for the on-screen displayJust Clock Just Clock onLanguage Access Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display On-Screen DisplaysOK or % Power Save ModeSelect Power Save Mode Colour System Set About Ntsc PlaybackOK or% Appears only with HR-DD858E and HR DD858EHBasic Playback Load a CassettePoint Start PlaybackPause During Playback Playback FeaturesActivate HIGH-SPEED Search Slow Motion For HR-J758E/EH High-Speed Turbo Search For HR-J758E/EHStill Picture/Frame-By-Frame Playback For HR-J758E/EH Adjust Tracking Activate 3R PictureOverride Automatic Tracking ManuallyActivate Instant Review Skip Over UnwantedSections Activate Spatializer SpatializerSoundtrack Selection During PlaybackRepeat Playback Audio signal during TimeScan TimeScanVariable-Speed Search HR-DD858E/EH only Press Pause Press TV Prog + or so that the vibration stopsTimeScan TimeScan AudioSpeed SP Speed LP Audio output HR-DD858EHR-DD858EHBasic Recording Recording Features Type of Broadcast On-screen Display Being Received Receiving Stereo Bilingual ProgrammesTo Record Stereo And Bilingual Programmes A2 Adjust Audio Hi-Fi Audio Recording Level Control HR-DD858E/EH onlyPreparation Select B.E.S.T. ModeS.T. Picture System Recording PlaybackOr press Record on the recorder During B.E.S.TTimer Programming Timer Warning Satellite Tuner UsersExpress Timer Programming Start TimeEnter Programme Stop TimeSET VPS/PDC Mode Timer ModeEngage RECORDER’S VPS/PDC RecordingCheck, Cancel And Replace Programmes PressPress Again to check More information. Each Time you pressFor Example Auto SP→LP TimerAuto Timer Before performing the following steps Prog REC ModeAutomatic Satellite Programme Recording Remote Control Functions Remove Power SupplySET Remote Control Code RE-SUPPLY PowerTV/VCR, TV +/- Volume SET TV Brand CodeOperate TV TV Prog +Satellite Tuner Multi-Brand Remote Control Operate Satellite TunerBefore you start Satellite Tuner Brand CodeSET Recording DECK’S Input Mode Edit To Or From Another Video RecorderMake Connections Start Source PlayerAV2 Select Setting SET RECORDER’S Input Mode Edit From a CamcorderStart Camcorder Start RecorderSET Input Mode Locate Start PointEngage Audio Dubbing Start DubbingReset the Counter Insert EditingLocate END Point ProgEND Insert Editing Engage Insert EditingStart Editing Back of Recorder Connection To Satellite TunerSatellite Tuner Unit Connecting Using a Decoder Select Input ModeConnect Decoder SET TunerConnecting Using a Stereo System AUX in or Tape MonitorAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelTuner Set Auto Channel SetPerform Auto Channel SET View Confirmation ScreenEnter NEW Channel Information Storing Channels ManuallyChange Station Channel Position When Receiving a Scrambled BroadcastDelete a Channel Access Manual Switch StationsChannel SET Screen Select NEW StationTV Station And ID List Station NamePerform Tuning Fine-Tuning Channels Already StoredSelect Channel to FINE-TUNE Press OK twice. The Manual Channel Set screen appearsShowview Setup NumberEnter Receiving Channel Position Number Guide Program Number SetAccess Initial SET Screen Access Clock SET ScreenClock Set SET Date and TimeStart Clock Operation SET Just ClockSET Clock Data Source Channel Position No power is applied to the recorder Remote control wont functionMains power cord is discon- nected If you’re using the RF OUT connec- tionTimer Recording EN Questions and Answers Ä remain lit on the display panel. Is there Problem?Index EN Index HR-DD858E/EH onlyRemote Control Frequency synthesized tuner Maximum recording timeIN/OUT x 1, IN/DECODER x Memo For More Information see INSTRUCTIONS/P4 Ex. Francais is selected for BelgiumInternational Telephone Language Code

Related manuals

Manual 64 pages 10.32 Kb