JVC HR-J668EU, HR-J711EU Basic Playback, Load a Cassette, Point, Start Playback, Stop Playback

Page 13

PLAYBACK

EN13

Basic

Playback

Turn on the TV and select the VIDEO channel (or AV mode).

[J711EU]		REW	PLAY
[J711EU]

		DISPLAY
STANDBY/ON
TIMER
REC LINK	TV PROG
	STOP/EJECT		FF
			FF
[J668EU]		REW	PLAY
STANDBY/ON
		DISPLAY
TIMER
REC LINK	TV PROG
	STOP/EJECT		FF
			FF

The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.

	1		LOAD A CASSETTE
		Make sure the window side is up, the rear label side is
			facing you and the arrow on the front of the cassette is
			pointed toward the recorder. Don’t apply too much
			pressure when inserting.

			● The recorder power comes on automatically and the
			counter is reset to 0:00:00.
			● If the record safety tab has been removed, playback
			begins automatically.

			FIND PROGRAMME START
	2		POINT
		If the tape is advanced past the start point, press REW.
			To go forward, press FF.
	3		START PLAYBACK
		Press PLAY. “BEST” appears blinking in the recorder's
			display panel during automatic tracking. (☞ pg. 20)
	4		STOP PLAYBACK
		Press STOP on the remote or STOP/EJECT on the
			recorder’s front panel. Then press STOP/EJECT to
			remove the cassette.

LAY
1	?

FF

REW

3

STOP

Tape Position Indicator

Usable cassettes

● Compact VHS camcorder recordings can be played on

this video recorder. Simply place the recorded cassette

into a VHS Cassette Adapter and it can be used just like

any full-sized VHS cassette.

The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of “5” in relation to “0”

(beginning) or “+” (end) 0 + shows you where you are

on the tape.

”O.S.D.” (☞ pg. 9) must

be set to “ON”, or the Beginning indicator will not appear.

3

+ +

1:23:45 REMAIN 2:35

End

● This video recorder can record on regular VHS and

Super VHS cassettes. However, it will record and play

back regular VHS signals only. It is not possible to play

back a recorded Super VHS tape.

NOTE:

Depending on the type of tape used, there may be times when the indication is not correct.

Image 13

Contents HR-J711EU HR-J668EU Safety First Safety PrecautionsFor Italy Do not place the recorderBasic Connections Check ContentsSituate Recorder Connect Recorder to MainsEN Initial Settings Auto Set UpIf you are referring to the front display panel If you are referring to the on-screen displayVia an RF cable only RF connection Language CodeYour TV to the Video Channel. Refer to ThisENU Preset DownloadLanguage for the on-screen display If both auto channel set and auto clock set have failedJust Clock Just Clock onLanguage ENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenOn-Screen Displays Return to Normal ScreenPower Save Mode Link Functions TV Auto Power OnLI NK NexTView LinkMode Colour System SetAbout Ntsc Playback Counter and tape remaining time readings will be incorrectLoad a Cassette Basic PlaybackPoint Start PlaybackPlayback Playback FeaturesActivate HIGH-SPEED Search Override Automatic Tracking Adjust TrackingManually Return to AutomaticSelect Picture Control SET Mode Access Mode SET ScreenEN Playback Basic Recording Recording Features Bilingual Programmes Receiving StereoTo Record Stereo And Bilingual Programmes A2 To Record Nicam Stereo And Bilingual ProgrammesEN Recording S.T. Picture SystemPreparation S.T., then press OK orPlayback RecordingOr press Record on the recorder EN Timer Recording Timer ProgrammingSatellite Tuner Users Timer WarningPress SP/LP Before performing Express Timer Programming Express Timer ProgrammingStart Time TimeTimer Mode SET VPS/PDC ModeEngage RECORDER’S VPS/PDC RecordingPress ä Timer Check, Cancel And Replace ProgrammesPress Again to check More information. Each Time you press Next programmesAuto Timer Auto SP→LP TimerAutomatic Satellite Programme Recording Prog REC ModeBefore performing the following steps Edit From a Camcorder SET Edit ModeMake Connections SET RECORDER’S InputEdit To Or From Another Video Recorder Input ModeSET Recording DECK’S Start Source PlayerRecorder AV2 Select SettingRecorder Player EN System Connections Connection To Satellite TunerSatellite Tuner Unit Back of TVDecoder Connector ScartSet AV2 Select to AV2. pg Select Input Mode Connecting Using a DecoderConnect Decoder SET TunerSpeaker Television Mains outlet Connecting Using a Stereo SystemTuner Set Access Auto CH SETEN Subsi Diary Sett Ings Auto Channel SetView Confirmation Screen Perform Auto Channel SETStoring Channels Manually SU Bsidiary SettingsDelete a Channel When Receiving a Scrambled BroadcastChange Station Channel Position Press %Þ @ #until the item you want to move beginsSwitch Stations Access ManualChannel SET Screen Select NEW StationTV Station And ID List Perform Tuning Access Manual Channel SET ScreenFine-Tuning Channels Already Stored Select Channel to FINE-TUNEExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET RF Output SystemTurn the Recorder on Clock SetSET Date and Time Recorder is preset to receive clock setting Default setting is OFF. Set as desired by pressingSET Just Clock Channel PositionNumber Showview SetupEnter Receiving Channel Position Number Guide Program Number SetTroubleshooting EN Roubleshooting Timer RecordingQuest Ions and Answers EN Ä remain lit on the display panel. Is there Problem?Front View J668EU IndexRear View VCR, TV Prog +/-,TV +/-, TV Muting EN IndexProvided accessories PAL-type colour signal and CcirSpeci Fications EMO Memo Ex. Francais is selected for Belgium Auto Set Up referring to the display panel