JVC HR-S9400EH Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 10

10ENINITIALSETTINGS(cont.)

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

If you have connected the video recorder to your TV via the provided RF cable only (RF connection) – Go to "With RF Connection" below.

If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection) or via the provided RF cable, the provided S-Video cable and the provided audio cable (S-VIDEO connection) – Go to "With AV or S-VIDEO Connection" on next page.

IMPORTANT:

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

With RF Connection

 

 

8

•• • • • •• •• • • • ••

 

• • • •

• • • •

1

 

STOP

 

 

2

2

1 2 3

4

5

6

7 8 9

04

TV PROG

3

OK

1

TEST SIGNAL

The channel on which the screen to

3

the left appear clearly in step 2 is

 

your Video Channel.

 

ACCESS VIDEO CHANNEL SET MODE

Hold down STOP on the recorder until the display panel shows the following.

SET VIDEO CHANNEL

Set your TV to UHF channel 36.

●If the two vertical white bars appear clearly on the screen as shown in the illustration at bottom left, go to step 3.

●If the two vertical white bars do not appear clearly, press TV PROG + or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area.

(Ex.) If channel 50 is available in your area

Then set your TV to UHF channel 50 and check if the two vertical white bars appear clearly on the screen; if so, go to step 3. If not, re-set the video recorder to another vacant channel and try again.

NOTES:

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

EXIT VIDEO CHANNEL SET MODE

Press OK.

To view picture signals from the video recorder, set your TV to the Video Channel.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents HR-S9400E/EH For Italy Safety PrecautionsDo not place the recorder Basic Connections Installing Your NEW Record ERFor Customers in Australia and New Zealand Connect Recorder to Mains Video ConnectionConnect Recorder to TV INS Talling YO UR NEW R EcorderRear view Back of TVSelect Country Auto Set UpTurn on the Recorder Nitial Sett IngsIf you are referring to the on-screen display Perform Auto SET UPSelect Language Language Code for the HR-S9400ELanguage for the on-screen display Initial SettingsIf both auto channel set and auto clock set have failed Just ClockLanguage EN Initial Settings Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetWith AV Or S-VIDEO Connection Make List of Stored Station Names Channel Positions SetupGuide Program Number Set Confirm Channel Position Number When Using a Satellite TunerEnter Showview Number Close MenuBasic PlaybackActivate FRAME-BY-FRAME Playback Playback FeaturesPause During Playback Activate SLOW-MOTION PlaybackManually Adjust TrackingOverride Automatic Tracking Return to AutomaticIndex Search Tape Position Indicator Instant ReViewActivate Instant Review EndSoundtrack Selection Activate SpatializerSpatializer During PlaybackActivate Scene Finder SET A/B Code SwitchRE-SUPPLY Power Stop Scene FinderTimeScan Audio signal during TimeScanTime Scan Indicator Variable-Speed Search/ Reverse PlayTimeScan Speed SP Speed LP Audio outputSelect Mode Access Main Menu ScreenAccess Mode SET Screen Return to Normal ScreenBasic Recording Watch Reset CounterSelect Channel to SET Counter DisplayTo Record Stereo And Bilin- gual Programmes A2 Locate Start Point Engage RECORD-PAUSE ModeLevel Resume RecordingOn-Screen Displays Access Main MenuENABLE/DISABLE ON-SCREEN Display Return to NormalWhen Using The Illumi-Guide Feature TimerEN Timer Recording Ming ScreenSatellite Tuner Users To timer-record a satellite broadcast using ShowviewPressing Prog Check Programming Regular TimerEN Timer RECORDINGcont Stop +/- , Date +/- , TV Prog +PDC/VPS Buttons remain lit Start +/-, Stop +/-, Date +Press TV Prog + +/- , Date +/- , TV Prog +/- and MenuCheck And Cancel Programmes Access ProgrammeAuto Timer Revise ProgrammeTimer Warning TimerAuto SP/LP Timer Engage Auto SP/LPFor Editing Editing Mode SettingPreparation EditingWhen using rear panel input connectors To Select The External Input ModeAV2 Select Setting When using front panel input connectorsEdit To Or From Another Video Recorder Your recorder PlayerRecorder Player Start Camcorder SET RECORDER’S Input ModeEdit From a Camcorder Start RecorderStart Dubbing SET Input ModeEngage Audio Dubbing END Audio DubbingInsert Editing Reset the CounterLocate END Point Start Editing Engage Insert EditingEND Insert Editing Prepare for Editing Access R.A. Edit ScreenRandom As- semble Editing Load Source CassetteStart R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. EditSET Jlip ID Number Access Jlip ID NO. SET ScreenTerminal JLIPJoint Level Interface Protocol Connector Info Rmation on J TerminalConnect Decoder Connecting Using a DecoderSelect Input Mode SET TunerConnecting Using a Stereo System EN System ConnectionsSpeaker SET TV Brand Code TV Multi Brand Remote ControlControl Your TV Using Additional Buttons TRY Operating TVTRY Operating Satellite Tuner Satellite Tuner MultiSET Satellite Tuner Brand Code Satellite Tuner Brand CodeAuto Channel Set Access Country SETTuner SET Press Push JOG toTo initiate Auto Channel Set Press Push JOG Move the highlight barPointer to Language of your Appears,Close Confirmation Select ItemDelete Channel Select NEW PositionPerform Tuning Switch StationsAccess Manual CH. SET Select NEW StationTV Station And ID List Station NameMove the highlight bar pointer to Clock SET by Clock SETPreparation Screen appearsSET Just Clock SET Clock AutomaticallySET Date and Time Start Clock OperationSet the TV receiver to the Video Troubleshooting E NPanel with Auto Timer set to OFF Indicator off Connection, set the TV to its AVOubleshooting Timer againCamcorder recording is not Camcorder has not been Ä remain lit on the display panel. Is there a problem? Questions and Answer S E NOpen the lid to access covered connectors and buttons IndexRear View How To Use Installing BatteriesEN Index Maximum recording time SpecificationsProvided in Australia and New Zealand only Language Code for the HR-S9400E HR-S9400E/EHInternational Telephone Country Code Language Code for the HR-S9400EH
Top Page Image Contents