JVC HR-S6856EK, HR-S6855EK, HR-S6857EK manual Advanced features

Page 49

advanced features

49

programme satellite receiver Enter the details of the programme into your satellite receiver (see receiver manual) and put a tape in the VCR.

get to the output/input set screen Press m. Move the highlight bar to OUTPUT/INPUT SET using the Aand Bbuttons and press O(or E).

select l-2 select mode Move the highlight bar to L-2 SELECT using the Aand B buttons. Press O(or E) to select A/V or SAT. Then press m.

set tape speed Press /on the Remote Control to set the tape speed to SP, LP or EP.

engage vcr in auto mode Press and hold SATcon the VCR for about 2 seconds. The SATc indicator on the VCR lights up and the VCR turns off automatically. Any signal detected at the AV2 (L-2) IN/DECODER connector will automatically start the VCR recording; when the signal stops, so will the VCR.

Notes

connectors Auto Satellite Prog Recording is only possible using the AV2 (L-2) IN/DECODER connector.

timer mode You cannot put the VCR into TIMER MODE when using Auto Satellite Prog Recording Mode.

rThe number of programmes recorded will not be displayed on the VCR display panel when the rbutton is pressed.

timer recording Auto Satellite Prog Recording is not possible if your satellite receiver does not have a timer.

indicator The SATcindicator light flashes when Auto Satellite Prog Recording is in progress.

disengage To disengage the VCR during Auto Satellite Prog Recording, press the obutton. The VCR will stop recording and turns off.

tape speed When recording two or more programmes consecutively, you cannot set a different tape speed for each programme. The first speed selected will apply to all programmes in that recording session.

b.e.s.t. The B.E.S.T. system will not work during Auto Satellite Prog Recording.

just clock Just Clock does not work when in Auto Satellite Prog Recording mode.

incoming signal The VCR will only react to the start of an incoming signal at the AV2 (L-2) IN/DECODER connector. If you try to engage Auto Satellite Prog Recording Mode whilst the satellite receiver is powered on, the SATcindicator light will flash but the VCR will not record. You must power the satellite receiver off then on again to begin recording in these circumstances.

cable input You can record in the same way from a cable system as long as you connect the cable system has a timer on/off function and is connected to the AV2 (L-2) IN/DECODER.

incompatibilities Some satellite receivers output signals even when turned off. These receiv- ers cannot be used with this VCR in this way.

Page 48 Page 50
Image 49
Page 48 Page 50
Contents HR-S6855EK HR-S6856EK HR-S6857EK If in doubt consult a competent electrician Safety PrecautionsMoisture Condensation On The Safe Use Of Equipment Some Do’s And Don’tsContents YQioptu Front Panel Diagram KeyGetting Everything Ready Welcome to JVCPerform Auto Setup pg Three-Step Quick Start Auto SetupThree step quick start Preset DownloadFinish Off Check the ResultsBasic Features Load a Video Cassette PlaybackPlay Stop & EjectRewind and Fast Forward Video Heads CleaningAdvanced JOG Dial Playback FeaturesPause During Playback Single Frame MovementVariable Speed Search Slow MotionHigh Speed Search Choose a Programme RecordingSet the Tape Speed Start RecordingDisplay Tape Remaining Time Check Elapsed Recording Time and Reset ItChange Display Information Recording Resume Function Instant Timer RecordingEnter the PlusCode Number Get to the Video Plus + ScreenPressing Cchanges the display to the programme Edit Programme Title Engage Timer ModeReturn to Normal Screen Get to the Programme Screen/Display Express Timer ProgrammingEnter Programme Details Ente Return to Normal Screen 24H Express Timer Programming Press c, then press oto disengage the timer mode Check, Cancel & Change ProgrammesWhen Programmes Overlap Each Other Advanced Features Manual Tracking Picture QualityVideo Stabilizer Picture Control Super VHS ET S-VHS ET Tape TypeTo record in S-VHS Super VHS S-VHS, S-VHS ET and VHSAvoiding B.E.S.T. Time Delay Recording and Playback Using B.E.S.TTurning B.E.S.T. on or OFF Nicam Stereo and Bilingual Broadcasts Sound ModesSoundtrack Selection Skip Search Finding Specific ScenesIndex Search Instant ReViewProgramme Navigation When inserting a cassette with the record safety tab intactNavigation Screen Navigation PlaybackEntering Character Delete Tape Data Link Functions TV Auto Power OnNexTView Link VCR Auto StandbyDirect Rec Installing Satellite Controller Satellite Receiver Control SettingsCode Setting satellite receiver’s brandCheck Result of Test Auto Record from Satellite Receiver Auto Satellite Programme RecordingAdvanced features Editing OUTPUT/INPUT SettingFor L-2 Select SELECT/INPUT SettingEditing Using Another VCR Your VCR as the Player Editing from a Camcorder On-Screen Display O.S.D Other FunctionsAuto SP aLP Timer Power Save ModeRepeat Playback Auto TimerNext Function Memory Connection to a Stereo System Exit Video Channel Set Mode Access Video Channel ModeVideo Channel Set Set Video ChannelTuner Set Auto Channel SetupManual Channel Setup Delete a Channel Change Station NameChange Station Preset Position TV Station ID Guide Fine-Tuning Stored ChannelsBBC1 BBC2 ITV CH4 CH5 TV Station Channel Number GuideClock Set Setting the ClockGuide Program Numbers Manually Setting Guide Program NumbersPlayback Questions and AnswersSymptom Possible Cause TroubleshootingRecording Other Problems List of Terms Memo Memo Memo HR-S6855/6856/6857EK
Top Page Image Contents