JVC HR-S8850EU specifications 14 EN, Perform Preset Download, Set the video channel

Page 14

14 EN

INITIAL SETTINGS (cont.)

Preset Download

Auto Channel Set by Downloading from TV/Auto Clock Set/Auto Guide Program Number Set

ATTENTION

You can use this function only with a TV offering T-V Link, etc.* Be sure to use a fully-wired 21-pin SCART cable.

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

If you have connected the recorder to your TV via the AV connection ( pg. 10), the recorder will automatically perform Preset Download instead of the Auto Set Up in step 4 on page 13. After downloading, the recorder sets the clock and Guide Program numbers automatically.

Perform steps 1 to 3 of “Auto Set Up” on page 12 before continuing.

A Perform Preset Download.

Press OK. The AUTO SET/T-V LINK display appears on the front display panel and/or on the TV screen.

On the front display panel

Press rt to select “CH – –” and press OK or e.

On the on-screen display

Press rt to move the highlight bar (pointer) to “T-V LINK” and press OK or e.

NOTES:

●For details, refer to the instruction manual of your TV.

●In the area where no TV station transmits a PDC (Programme Delivery Control) signal, the recorder can perform neither Auto Clock Set nor Auto Guide Program Number Set.

●If there is a power cut, or if you press 1 or MENU while downloading or set up is in progress, it will be interrupted; be sure to turn off the recorder power once and try again from the beginning.

●Auto Clock Set may not function properly depending on the reception condition.

●On this recorder, the characters available for station names (ID) are A–Z, 0–9, –, f, + and I (space). Some names of

downloaded stations may differ from those of your TV ( pg. 68).

Preset positions on the front display panel increase from “CH1”; do NOT press any button on the recorder or remote control until the front display panel shows clock time, “(CH) 1” or “– –:– –” as illustrated on page 15.

●If you are using the on-screen display, the T-V LINK screen

will appear. Then the GUIDE PROG SET screen will appear during Guide Program Number Set. When Preset Download is completed, “COMPLETED” appears for about 5 seconds, then the normal screen appears.

●If you press any button on the recorder or remote control while downloading is in

progress, it will be interrupted.

B Set the video channel.

Set the video channel to off manually. ( pg. 72)

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Connector cover Front ViewRear View Front Display Panel ON-SCREEN Display Remote Control How To Use Remote Control LCDSituate the recorder Check the contents10 EN Connect the recorder to TV 8To connect to a TV with S-VIDEO/AUDIO in connectors Video ConnectionTurn on the recorder Auto Set Up12 EN Select your countryPress rt to select your language code Perform Auto Set UpSelect the language Press rt to select Auto and press OK or eSet the video channel Perform Preset Download14 EN Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 16 ENAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link Basic Playback 20 ENPause during playback Slow MotionHigh-Speed Turbo Search Activate frame-by-frame playbackIndex Search 22 ENVariable Speed Search Skip SearchManual Tracking Next Function MemoryRepeat Playback Soundtrack Selection24 EN Instant Timer Recording ITR Tape Remaining TimeRetake Engage the Record-Pause mode26 EN Locate the start pointEngage the S-VHS ET mode Receiving Stereo and Bilingual Programmes ReceivedPlayback RecordingAccess the Showview Program screen Access the Showview displayAccess the Showview screen 30 ENEngage the recorder’s timer mode Set the VPS/PDC modeAccess the Title Edit screen Enter the programme titleExpress Timer Programming 32 ENEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Press PR+34 EN Enter the programme modeBefore performing the 24 Hour Express Timer Programming Set the programme start/stop time and channelReturn to the timer mode Cancel or change a programmeDisengage the timer mode Access the Programme Check screen/displaySelect the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenProgramme Recording Select the L-2 Select modeRecording mode Before performing the following stepsNavigation 38 ENLoad a recorded cassette Navigation PlaybackProgramme Navigation Screen Select a programmeSelect the programme 40 ENEdit Programme Title Delete the tape data Entering CharacterDelete Tape Data Example Enter JVC NewsCheck the remote control code for the recorder Remote A/B Code SwitchingSet the remote control code 42 ENOperate the TV TV Multi-Brand Remote ControlSet the TV brand code Set the satellite receiver brand code Satellite Receiver Multi-Brand Remote Control44 EN Operate the satellite receiverEdit From a Camcorder Set the recorder’s input modeSet the edit mode Start the camcorderAccess the Output/Input Set screen 46 ENSelect and L-2 Input Setting Decoder connectorAnother Video Recorder 48 ENPlayer Audio Dubbing 50 ENEnd Audio Dubbing Engage the Audio Dubbing modeStart dubbing Press AUX number key 0 and/or PR to select F-1 or S-1Insert Editing 52 ENLocate the end point Engage the Insert Editing modeAV Insert Editing Start EditingConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Connect the decoder Select the input mode56 EN Set the tunerConnecting/Using a Stereo System Make connectionsSelect the mode Mode SetAccess the Mode Set screen Select the mode settingDisengaged when the recorder is powered back on When viewing overplayedWhen this function is set to ON, the timer is automatically System to on or OFF  pg60 EN On the remote control, or press 7 on the recorderEntire programme while timer-recording in SP mode Function  pg , set PROG. Navigation to OFFPower consumption while the recorder is turned off When this function is set to ON, the Digital 3R pictureWhen this function is set to ON, you can reduce When this function is set to ON, you can automatically62 EN About Ntsc PlaybackGuide Program Number Showview System SetupGuide Program Number Set Enter the Guide Program number64 EN Access the Auto Channel Set screenTuner Set Auto Channel SetPress OK twice Perform Auto Channel SetView the Confirmation screen 66 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations B 68 ENSet Stations a TV Station And ID List Station Name70 EN Access the Clock Set screenClock Set Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode 72 ENPower 74 EN RecordingOther Problems 76 EN PlaybackScan system Signal-to-noise ratio 45 dB Horizontal resolutionMemory backup time Approx min Lines VHS78 EN Liste of TermsMemo International telephone Language code Country code
Top Page Image Contents