JVC HR-S8850EU specifications 60 EN, Function  pg , set PROG. Navigation to OFF, For Example

Page 60

60 EN

 

 

SUBSIDIARY SETTINGS (cont.)

 

 

 

* The default setting is bold in the table below.

 

 

 

 

 

8 PROG. NAVIGATION

 

When this function is set to “ON”, the recorder stores information on the

ON

 

recorded programmes. If you do not want to use the Programme Navigation

OFF

 

function ( pg. 38), set “PROG. NAVIGATION” to “OFF”.

 

 

NOTES:

 

 

 

 

● Programme Navigation is possible with the cassettes recorded with this recorder

 

 

only.

 

 

 

 

● Before recording, make sure the recorder’s clock is set correctly.

 

 

● To record the programme information in this recorder’s memory, you must continue

 

 

to record each programme for over the minimum recording time; 8 minutes for the

 

 

SP mode, 15 minutes for the LP mode or 23 minutes for the EP mode.

 

 

● Programme Navigation may not work properly depending on the tape being used.

 

 

● The programme information is stored in this recorder’s memory. If the memory in this

 

 

recorder should ever be damaged and the programme information lost, it is

 

 

impossible to restore that information.

 

 

 

 

 

8 DIRECT REC

 

When this function is set to “ON”, you can easily start recording the

ON

 

programme that you are watching on your TV. Press and hold 7 and press 4

OFF

 

on the remote control, or press 7 on the recorder.

 

 

NOTES:

 

 

 

 

● When you use the Direct Rec function, be sure to use a TV offering T-V LINK, etc.

 

 

and connect a fully-wired 21-pin SCART cable between the recorder and the TV

 

 

( pg. 10).

 

 

 

 

● If “DIRECT REC” is set to “OFF”, the 7 button functions as described in “Basic

 

 

Recording” ( pg. 24).

 

 

 

 

● During the Direct Rec, “– –” appears on the front display panel.

 

 

● Retake function ( pg. 26) does not work during Direct Rec.

 

 

 

 

 

8 AUTO SP]LP TIMER

 

When this function is set to “ON”, the recorder automatically switches to LP

ON

 

mode to allow complete recording if there is not enough tape to record the

OFF

 

entire programme while timer-recording in SP mode.

 

 

For Example . . .

 

 

 

 

Recording a programme of 210 minutes in length onto a 180-minute tape

 

 

Approximately 150 minutes

Approximately 60 minutes

 

 

SP mode

LP mode

 

 

 

 

 

 

 

 

Total 210

minutes

 

 

 

Make sure you set this function to “ON”, before the timer-recording starts.

 

 

NOTES:

 

 

 

 

● If you have programmed the recorder to timer-record 2 or more programmes, the

 

 

second programme and those thereafter may not fit on the tape if you set “AUTO

 

 

SP]LP TIMER” to “ON”. In this case, make sure the mode is not engaged, then set

 

 

the tape speed manually during timer programming.

 

 

● In order to ensure that the recording fits on the tape, this feature may leave a slight

 

 

non-recorded section at the end of the tape.

 

 

● There may be some noise and sound disturbance at the point on the tape where the

 

 

recorder switches from SP to LP mode.

 

 

● The Auto SP]LP Timer feature is not available during ITR (Instant Timer Recording),

 

 

and the feature will not work properly with any tapes longer than E-180, or with

 

 

some tapes of shorter lengths.

 

 

 

 

● If you perform timer recording with both VPS/PDC and the Auto SP]LP Timer

 

 

activated, and the programme goes beyond its originally scheduled length, there

 

 

may be times when the programme cannot be recorded in its entirety.

 

 

 

 

 

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Connector cover Front ViewRear View Front Display Panel ON-SCREEN Display Remote Control How To Use Remote Control LCDCheck the contents 10 ENSituate the recorder Connect the recorder to TV8To connect to a TV with S-VIDEO/AUDIO in connectors Video ConnectionAuto Set Up 12 ENTurn on the recorder Select your countryPerform Auto Set Up Select the languagePress rt to select your language code Press rt to select Auto and press OK or ePerform Preset Download 14 ENSet the video channel Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockAccess the Main Menu screen Access the Country Set screenLanguage 16 ENInstalling Satellite Controller Situate the Satellite ControllerAttach the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 20 ENSlow Motion High-Speed Turbo SearchPause during playback Activate frame-by-frame playback22 EN Variable Speed SearchIndex Search Skip SearchNext Function Memory Repeat PlaybackManual Tracking Soundtrack Selection24 EN Instant Timer Recording ITR Tape Remaining TimeEngage the Record-Pause mode 26 ENRetake Locate the start pointEngage the S-VHS ET mode Receiving Stereo and Bilingual Programmes ReceivedPlayback RecordingAccess the Showview display Access the Showview screenAccess the Showview Program screen 30 ENSet the VPS/PDC mode Access the Title Edit screenEngage the recorder’s timer mode Enter the programme titleExpress Timer Programming 32 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR+Enter the programme mode Before performing the 24 Hour Express Timer Programming34 EN Set the programme start/stop time and channelCancel or change a programme Disengage the timer modeReturn to the timer mode Access the Programme Check screen/displayCancel or change programme setting Confirm the overlapping programmesSelect the programme to modify Overlapping programmes blink on the TV screenSelect the L-2 Select mode Recording modeProgramme Recording Before performing the following stepsNavigation 38 ENNavigation Playback Programme Navigation ScreenLoad a recorded cassette Select a programme40 EN Edit Programme TitleSelect the programme Entering Character Delete Tape DataDelete the tape data Example Enter JVC NewsRemote A/B Code Switching Set the remote control codeCheck the remote control code for the recorder 42 ENTV Multi-Brand Remote Control Set the TV brand codeOperate the TV Satellite Receiver Multi-Brand Remote Control 44 ENSet the satellite receiver brand code Operate the satellite receiverSet the recorder’s input mode Set the edit modeEdit From a Camcorder Start the camcorderAccess the Output/Input Set screen 46 ENSelect and L-2 Input Setting Decoder connectorAnother Video Recorder 48 ENPlayer Audio Dubbing 50 ENEngage the Audio Dubbing mode Start dubbingEnd Audio Dubbing Press AUX number key 0 and/or PR to select F-1 or S-1Insert Editing 52 ENEngage the Insert Editing mode AV Insert EditingLocate the end point Start EditingConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Select the input mode 56 ENConnect the decoder Set the tunerConnecting/Using a Stereo System Make connectionsMode Set Access the Mode Set screenSelect the mode Select the mode settingWhen viewing overplayed When this function is set to ON, the timer is automaticallyDisengaged when the recorder is powered back on System to on or OFF  pgOn the remote control, or press 7 on the recorder Entire programme while timer-recording in SP mode60 EN Function  pg , set PROG. Navigation to OFFWhen this function is set to ON, the Digital 3R picture When this function is set to ON, you can reducePower consumption while the recorder is turned off When this function is set to ON, you can automatically62 EN About Ntsc PlaybackShowview System Setup Guide Program Number SetGuide Program Number Enter the Guide Program numberAccess the Auto Channel Set screen Tuner Set64 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice 66 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel68 EN Set Stations aSet Stations B TV Station And ID List Station NameAccess the Clock Set screen Clock Set70 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operationAccess the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set 72 ENPower 74 EN RecordingOther Problems 76 EN PlaybackSignal-to-noise ratio 45 dB Horizontal resolution Memory backup time Approx minScan system Lines VHS78 EN Liste of TermsMemo International telephone Language code Country code

HR-S8850EU specifications

The JVC HR-S8850EU is one of the standout VHS videocassette recorders from the late 1990s, designed to cater to the needs of both casual viewers and avid collectors of video content. This model is still recognized today for its robust features, advanced technologies, and overall reliability.

At the core of the HR-S8850EU's appeal is its excellent video quality. The unit employs JVC's Super VHS technology, which offers significantly improved resolution over standard VHS recordings. This allows users to capture and playback their favorite shows and home videos with remarkable clarity. It also features S-VHS ET, enabling the recording of standard VHS tapes with enhanced quality, making it a versatile choice for all types of video content.

One of the hallmark features of the HR-S8850EU is its dual-head design, which improves playback performance and fidelity. This model also incorporates various video and audio enhancements, including Digital Noise Reduction, which helps in minimizing the noise that can detract from the viewing experience. The use of professional-grade components ensures durability and longevity, making it a reliable choice for long-term use.

Another significant characteristic of the HR-S8850EU is its capability for timer recording. Users can easily set up the VCR to record shows at specified times, and with its built-in clock and programmable features, it seamlessly integrates into a home entertainment system. The presence of a 4-head system provides flexibility in viewing and recording, allowing users to access a variety of recording modes.

The HR-S8850EU also includes features such as automatic tracking, which optimizes playback for various tape conditions, and an intuitive On-Screen Display (OSD) for easy navigation through settings and functions. Additionally, the unit is equipped with multiple input and output terminals, including S-Video output, composite video, and audio connections, offering compatibility with a range of devices and ensuring that it can adapt to various home theater setups.

In summary, the JVC HR-S8850EU is a sophisticated yet user-friendly VCR that combines high-quality video recording capabilities with advanced features and technologies. Its blend of reliability, superior playback quality, and ease of use has made it a cherished model for enthusiasts and casual users alike, solidifying its status in the history of home entertainment technology.
Top Page Image Contents