JVC HR-S8850EU 72 EN, Access the Video Channel Set mode, Set the RF output system

Page 72

72 EN

SUBSIDIARY SETTINGS (cont.)

Video Channel Set

Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the recorder through the RF cable.

IMPORTANT

Perform the following steps only if —

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.

If you have connected the recorder to your TV via the AV or S-VIDEO connection ( pg. 10, 11), since you do not need the video channel you have to set the video channel to off.

If you have connected the recorder to your TV via the RF connection ( pg. 10), you have to set the correct video channel.

Before performing the following steps:

Make sure the recorder’s power is off and there is no cassette inserted in the recorder.

A Access the Video Channel Set mode.

Hold down 0 on the recorder until the front display panel shows the following.

B Set the RF output system.

The blinking number on the display indicates the RF output system of your country.

●If you have selected MAGYARORSZÁG (36), CESKÁ

REPUBLIKA (42), POLSKA (48) or OTHER EASTERN EUROPE (EE) for the country setting ( pg. 12, 16), press rt to set to “2”.

●For other countries, set to “1”. Then press OK. (1: B/G 2: D/K)

Then set your TV to UHF channel 50.

●If the two vertical white bars appear clearly on the TV screen as shown to the right, go to step 4.

●If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

NOTES:

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

D Exit the Video Channel Set mode.

Press OK on the remote control.

C Set the video channel.

With AV or S-VIDEO Connection

Press PR – until the front display panel shows “1OUT– –” (or “2OUT– –”).

●Now the video channel is set to off.

With AV or S-VIDEO Connection

To view picture signals from the video recorder, set your TV to its AV mode.

With RF Connection

The channel on which the TV screen in step 3 appears clearly is your video channel.

To view picture signals from the video recorder, set your TV to the video channel.

With RF Connection

Press PR + or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area.

(Example) If channel 50 is available in your area

Page 71 Page 73
Image 72
Page 71 Page 73
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Connector cover Front ViewRear View Front Display Panel ON-SCREEN Display Remote Control How To Use Remote Control LCDCheck the contents 10 ENSituate the recorder Connect the recorder to TV8To connect to a TV with S-VIDEO/AUDIO in connectors Video ConnectionAuto Set Up 12 ENTurn on the recorder Select your countryPerform Auto Set Up Select the languagePress rt to select your language code Press rt to select Auto and press OK or ePerform Preset Download 14 ENSet the video channel Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockAccess the Main Menu screen Access the Country Set screenLanguage 16 ENInstalling Satellite Controller Situate the Satellite ControllerAttach the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 20 ENSlow Motion High-Speed Turbo SearchPause during playback Activate frame-by-frame playback22 EN Variable Speed SearchIndex Search Skip SearchNext Function Memory Repeat PlaybackManual Tracking Soundtrack Selection24 EN Instant Timer Recording ITR Tape Remaining TimeEngage the Record-Pause mode 26 ENRetake Locate the start pointEngage the S-VHS ET mode Receiving Stereo and Bilingual Programmes ReceivedPlayback RecordingAccess the Showview display Access the Showview screenAccess the Showview Program screen 30 ENSet the VPS/PDC mode Access the Title Edit screenEngage the recorder’s timer mode Enter the programme titleExpress Timer Programming 32 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR+Enter the programme mode Before performing the 24 Hour Express Timer Programming34 EN Set the programme start/stop time and channelCancel or change a programme Disengage the timer modeReturn to the timer mode Access the Programme Check screen/displayCancel or change programme setting Confirm the overlapping programmesSelect the programme to modify Overlapping programmes blink on the TV screenSelect the L-2 Select mode Recording modeProgramme Recording Before performing the following stepsNavigation 38 ENNavigation Playback Programme Navigation ScreenLoad a recorded cassette Select a programme40 EN Edit Programme TitleSelect the programme Entering Character Delete Tape DataDelete the tape data Example Enter JVC NewsRemote A/B Code Switching Set the remote control codeCheck the remote control code for the recorder 42 ENTV Multi-Brand Remote Control Set the TV brand codeOperate the TV Satellite Receiver Multi-Brand Remote Control 44 ENSet the satellite receiver brand code Operate the satellite receiverSet the recorder’s input mode Set the edit modeEdit From a Camcorder Start the camcorderAccess the Output/Input Set screen 46 ENSelect and L-2 Input Setting Decoder connectorAnother Video Recorder 48 ENPlayer Audio Dubbing 50 ENEngage the Audio Dubbing mode Start dubbingEnd Audio Dubbing Press AUX number key 0 and/or PR to select F-1 or S-1Insert Editing 52 ENEngage the Insert Editing mode AV Insert EditingLocate the end point Start EditingConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Select the input mode 56 ENConnect the decoder Set the tunerConnecting/Using a Stereo System Make connectionsMode Set Access the Mode Set screenSelect the mode Select the mode settingWhen viewing overplayed When this function is set to ON, the timer is automaticallyDisengaged when the recorder is powered back on System to on or OFF  pgOn the remote control, or press 7 on the recorder Entire programme while timer-recording in SP mode60 EN Function  pg , set PROG. Navigation to OFFWhen this function is set to ON, the Digital 3R picture When this function is set to ON, you can reducePower consumption while the recorder is turned off When this function is set to ON, you can automatically62 EN About Ntsc PlaybackShowview System Setup Guide Program Number SetGuide Program Number Enter the Guide Program numberAccess the Auto Channel Set screen Tuner Set64 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice 66 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel68 EN Set Stations aSet Stations B TV Station And ID List Station NameAccess the Clock Set screen Clock Set70 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operationAccess the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set 72 ENPower 74 EN RecordingOther Problems 76 EN PlaybackSignal-to-noise ratio 45 dB Horizontal resolution Memory backup time Approx minScan system Lines VHS78 EN Liste of TermsMemo International telephone Language code Country code
Top Page Image Contents