JVC HR-S9600EK setup guide Audio Dubbing

Page 41

 

 

41

Audio Dubbing

Audio dubbing replaces the normal audio sound of a previously

recorded tape with a new soundtrack.

 

Normal audio track

Pre-recorded tape

 

Video/Hi-Fi audio

 

 

track

 

 

AUDIO

 

MONITOR

CD Player etc.

 

CD Player etc.

Mixer

Audio mixer

output

 

Original sound

 

AUDIO OUT

 

STOP

.DUB

 

 

8

 

 

A

1

3

 

 

2

 

TV

PROG

PLAY

PAUSE

 

 

NOTES:

●When monitoring the sound during Audio Dubbing, the normal soundtrack is automatically selected. If you wish to hear the mixed sound (Hi-Fi + Normal soundtracks), press

AUDIO on the remote control to select " + (L+R) + NORM" (☞ pg. 29).

●Audio dubbing stops automatically when the counter reaches "0:00:00", and the recorder enters the Play mode. Check the counter reading before dubbing.

●Audio dubbing is also possible using the rear panel AV1 IN/OUT or AV2 IN/DECODER connector. When using these connectors, make sure to select the correct input mode in step 2.

●Audio dubbing cannot be performed on a cassette that has had its record safety tab removed.

●When playing back an audio-dubbed tape, press AUDIO on the remote control to select the soundtrack you wish to hear (☞ pg. 29).

1

2

3

4

5

6

Audio-dubbed tape

MAKE CONNECTIONS

Connect an audio component to the AUDIO L + R connectors on the recorder's front panel.

●When connecting monaural equipment, use only the recorder's AUDIO L connector.

SET INPUT MODE

Press NUMBER key "0" and/or TV PROG so that "F-1" or "S-1" appears in place of a channel number.

LOCATE START POINT

Press PLAY to start playback of the tape in your recorder, and press PAUSE when you find the point where you want to start dubbing.

ENGAGE AUDIO DUBBING

Press A. DUB.

●It is possible to take the original sound recorded on the tape in your recorder and mix it with other sounds from a microphone, CD player etc. To perform this audio dubbing with audio mixing, connect as in the diagram on the left.

●Your recorder enters the Audio Dubbing Pause mode. ("" blinks, "" and "" light up on the front display panel.)

●To perform audio dubbing with audio mixing, press AUDIO MONITOR (or AUDIO on the remote control) to select " + (L+R)" at this point.

*Audio dubbing with audio mixing is not possible if you're using a monaural audio component, or if you don't have an audio mixer.

START DUBBING

Engage the audio component's Play mode, then press PLAY to start the tape in your recorder. Audio dubbing begins at this point.

●"" blinks and "" is displayed on the front display panel.

●To stop dubbing temporarily, press PAUSE. Press PLAY to resume dubbing.

END AUDIO DUBBING

Press STOP to stop the tape in your recorder, and engage the audio component's Stop mode.

Page 40 Page 42
Image 41
Page 40 Page 42
Contents HR-S9600EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder Connect Video Recorder to TVBack of TV Mains outlet Mains Power Cord Back of TV Audio in connectorsGo to item Before performing the following procedure, make sure that10 or If -- appears on the display panel, refer Remote control while downloading isLink screen will appear. Then the Guide Program number setIf both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLink Functions TV Auto Power OnTurn on the Recorder NexTView LinkLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayAccess Video PLUS+ Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Program Screen Enter Pluscode NumberPDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypeAccess Mode SET Access Main MenuSelect B.E.S.T. Mode Playback/ Recording According To Tape Charac- teristicsPlayback RecordingOr press Record on the recorder During B.E.S.TManual Tracking Playback Picture AdjustmentDigital TBC/NR Digital 3RActivate Index Search Looking For Scene You WantActivate Instant Review Skip Over UnwantedTimeScan Audio signal during TimeScanVariable-Speed Search/ Reverse Play Normal recorderTimeScan Audio TimeScanSpeed SP Speed LP Audio output Forward Search Play Slow-Motion StillSelecting Sound You Want Adjust AudioControl Screen Recording LevelSoundtrack Selection Receiving Nicam Stereo And Bilingual ProgrammesDuring Playback Type of Broadcast On-screen Display Being ReceivedSatellite Receiver Unit Automatic Satellite Programme RecordingLink indicator lights up and the recorder turns off Move the highlight bar pointer to Mode SET byBefore performing the following steps Pressing %Þ, then press OK or%RE-SUPPLY Power SET Remote ControlRemote A/B Code Switching Remote Con- trol FunctionsControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVOperate Satellite Receiver Satellite Receiver Multi- Brand Remote ControlTV Prog +/-,NUMBER keys Satellite Tuner Brand CodeAccess Mode SET Screen Access Main Menu ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Repeat steps 4 6 as necessary Connector Lanc Cable not providedSynchro Editing Edit To Or From Another Video Recorder TV Receiver Player Your recorder Recorder AV2 Select Setting AV1 Select SettingAudio Dubbing Press R.A. Edit Random As- semble EditingPrepare for Editing Locate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditNumber Reset the CounterInsert Editing Start Editing Engage Insert EditingEND Insert Editing DUBAccess Initial SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Jlip ID NO. SET Screen Information On J TerminalOther Functions ENABLE/DISABLEON-SCREEN Display On-Screen DisplaySelect Power Save Power Save ModeNext Function Memory Auto SP→LP TimerAuto Timer Resume Recording Engage RECORD-PAUSE ModeRepeat Playback RetakeAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalAuto Channel Set Tuner SetPerform Auto Channel SET After Scan Completed Screen preset positionsIs displayed on the screen For about 5 seconds, aInput Channel Storing Channels ManuallyEnter NEW Channel Information Close Confirmation ScreenDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Switch Stations Access ManualChannel SET Screen Select NEW StationStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Ä remain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Won’t stop Timer RecordingFront View Index3 4 5 6 @ # $ Inside View of Front PanelRear View AV1 IN/OUT Connector enables AV connec@ # Display PanelTV Muting Button mutes sound Remote ControlFast Forward FF Button same as button on recorder. pg Remote Control LCDVHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical
Top Page Image Contents