JVC HR-S9600EK setup guide Connect Video Recorder to TV, Back of TV, Back of Recorder

Page 6

6

QUICKSETUPGUIDE(cont.)

STEP

2

INSTALLATION

CONNECT VIDEO RECORDER TO TV

Place the recorder on a stable, flat surface.

Back of TV

Aerial connector

21-pin AV input connector (SCART)

RF Cable (provided)

21-pin SCART Cable (not provided)

Make this connection if your TV has a

21-pin AV input connector (SCART) in order to reduce the possibility of interference. And if you are using a stereo TV, you will

need this cable in order to enjoy stereo playback of videotapes.

TV Aerial Cable (not provided)

Mains Power Cord

AV1 OUT

 

 

S OUT

AV1 IN/OUT

L

COMP. Y/C

 

AUDIO

 

 

OUT

 

 

R

AV2 IN/DECODER

Mains outlet

AV1 OUT switch

SYNCHRO EDIT

 

JLIP

ANT. IN

PAUSE/R.A. EDIT

RF OUT

Back of Recorder

RF CONNECTION

To connect to a TV with NO 21-pin AV input connector (SCART) . . .

1– Disconnect the TV aerial cable from the TV.

2– Connect the TV aerial cable to the ANT. IN jack on the rear panel of the recorder.

3– Connect the provided RF cable between the RF OUT jack on the rear panel of the recorder and the TV’s aerial connector.

AV CONNECTION

To connect to a TV with 21-pin AV input connector (SCART) . . .

1– Connect the aerial, recorder and TV as per “RF CONNECTION”. 2– Connect an optional SCART cable between the AV1 IN/OUT socket on the rear panel of the recorder and the TV’s 21-pin

AV input connector (SCART).

3– Set the AV1 OUT switch to the appropriate position. See "AV1

INPUT/OUTPUT SIGNAL SELECTION FOR AV CONNEC- TION" below.

AV1 INPUT/OUTPUT SIGNAL SELECTION FOR AV CONNECTION

The AV1 IN/OUT connector accepts and delivers either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). For input signal selection, select "VIDEO" (regular video signal) or "S-VIDEO" (Y/C signal) for "AV1 SELECT" setting (☞ pg. 40). For output signal selection, use AV1 OUT switch of the rear panel.

●If your TV's 21-pin AV input connector (SCART) is compatible only with the regular video signal, set this switch to COMP.

●If your TV's 21-pin AV input connector (SCART) is compatible with the Y/C signal, set this switch to Y/C. You can obtain high- quality S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

NOTES:

●Set your TV to the VIDEO (or AV), Y/C, or RGB mode according to the type of your TV's SCART connector.

●For switching the TV's mode, refer to the instruction manual of your television.

●To obtain high-quality S-VHS pictures, you can also use the S-VIDEO CONNECTION described on page 7.

ATTENTION

■Do NOT Plug the mains power cord into a mains outlet until all connections are completed.

■Do NOT press the button on the recorder or on the remote control to turn on the recorder's power before you start the Auto Set Up procedure described on page 8.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents HR-S9600EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Connect Video Recorder to TV Back of TVBack of Recorder Back of TV Audio in connectors Mains outlet Mains Power CordBefore performing the following procedure, make sure that Go to itemLink screen will appear. Then the Guide Remote control while downloading is10 or If -- appears on the display panel, refer Program number setAuto Set Up results appear on the display panel If both auto channel set and auto clock set have failedTurn on the Recorder TV Auto Power OnLink Functions NexTView LinkPoint PlaybackLoad a Cassette Start PlaybackPlayback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayAccess Video PLUS+ Program Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Enter Pluscode NumberTimer Warning PDC RecordingEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSSelect B.E.S.T. Mode Access Main MenuAccess Mode SET Playback/ Recording According To Tape Charac- teristicsOr press Record on the recorder RecordingPlayback During B.E.S.TDigital TBC/NR Playback Picture AdjustmentManual Tracking Digital 3RActivate Instant Review Looking For Scene You WantActivate Index Search Skip Over UnwantedVariable-Speed Search/ Reverse Play Audio signal during TimeScanTimeScan Normal recorderSpeed SP Speed LP Audio output TimeScanTimeScan Audio Forward Search Play Slow-Motion StillControl Screen Adjust AudioSelecting Sound You Want Recording LevelDuring Playback Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedAutomatic Satellite Programme Recording Satellite Receiver UnitBefore performing the following steps Move the highlight bar pointer to Mode SET byLink indicator lights up and the recorder turns off Pressing %Þ, then press OK or%Remote A/B Code Switching SET Remote ControlRE-SUPPLY Power Remote Con- trol FunctionsSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Operate TVTV Prog +/-,NUMBER keys Satellite Receiver Multi- Brand Remote ControlOperate Satellite Receiver Satellite Tuner Brand CodeSelect Picture Control SET Mode Access Main Menu ScreenAccess Mode SET Screen Minimizing Picture Degradation While EditingEdit From Camcorder Connector Lanc Cable not provided Synchro EditingRepeat steps 4 6 as necessary Edit To Or From Another Video Recorder TV Receiver Player Your recorder Recorder AV1 Select Setting AV2 Select SettingAudio Dubbing Random As- semble Editing Prepare for EditingPress R.A. Edit Start R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. EditReset the Counter Insert EditingNumber END Insert Editing Engage Insert EditingStart Editing DUBAccess Jlip ID NO. SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Information On J TerminalON-SCREEN Display ENABLE/DISABLEOther Functions On-Screen DisplayPower Save Mode Select Power SaveAuto SP→LP Timer Auto TimerNext Function Memory Repeat Playback Engage RECORD-PAUSE ModeResume Recording RetakeConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionTuner Set Perform Auto Channel SETAuto Channel Set Is displayed on the screen Screen preset positionsAfter Scan Completed For about 5 seconds, aEnter NEW Channel Information Storing Channels ManuallyInput Channel Close Confirmation ScreenChange Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Channel SET Screen Access ManualSwitch Stations Select NEW StationTV Station And ID List Station NameTV Station Channel Number Guide Clock Set Just ClockVideo Plus+ Setup NumberGuide Program Number Set Questions And Answers Ä remain lit on the display panel. Is there Problem?Troubleshooting Timer Recording Won’t stopIndex Front ViewInside View of Front Panel 3 4 5 6 @ # $AV1 IN/OUT Connector enables AV connec Rear ViewDisplay Panel @ #Remote Control TV Muting Button mutes soundRemote Control LCD Fast Forward FF Button same as button on recorder. pgMaximum recording time DA4 Double Azimuth helicalVHF 44.5 143/143 470 MHz
Top Page Image Contents