JVC HR-S9600EK Engage RECORD-PAUSE Mode, Resume Recording, Repeat Playback, Retake, Ntsc Playback

Page 50

50ADVANCEDOPERATIONS(cont.)

Repeat Playback

Your video recorder can automatically play back the whole tape 50 times repeatedly.

1–:–

2

 

 

 

1

2

3

 

4

5

6

 

7

8

9

3

 

0

 

4

 

 

4

1

 

 

3

 

 

 

2

 

 

 

FF

REW

 

STOP

PAUSE

 

Retake

You can cut out unnecessary parts of a TV programme while you're recording it.

End of programme

Beginning of programme

 

 

 

 

Programme

Unnecessary

Unnecessary

Programme

 

part

part

 

 

 

 

 

Recorded part

Go back to end of programme to cut out unnecessary part

ENGAGE RECORD-PAUSE MODE

1 Press PAUSE during recording.

LOCATE START POINT

2 Turn the JOG dial to the left or right (or hold down REW or FF) and release it when you reach the point where you want to resume recording.

* Your recorder returns to the Record-Pause mode.

RESUME RECORDING

3 Press PLAY when you wish to resume recording.

NOTE:

1

 

START PLAYBACK

 

Press PLAY.

2

 

ACTIVATE REPEAT PLAYBACK

 

Press PLAY and hold for over 5 seconds, then release.

 

 

 

The Play indicator ( ) on the display panel blinks

 

slowly.

 

 

The tape plays 50 times automatically, and then stops.

 

 

 

3

 

STOP PLAYBACK

 

Press STOP at any time to stop playback.

NOTE:

Pressing PLAY, REW, FF or PAUSE also stops Repeat Playback.

NTSC Playback

Your video recorder is equipped with NTSC circuitry that can play back NTSC tapes.

1

 

LOAD A CASSETTE

 

Insert a cassette recorded in NTSC.

2

 

START PLAYBACK

 

Press PLAY.

 

 

 

"NTSCPAL" appears on the screen for about 5

 

seconds.

 

 

Some TVs shrink the picture vertically and place

 

 

black bars at the top and bottom of the screen. This is

 

 

not a malfunction on the part of either the video

 

 

recorder or the TV.

 

 

The picture may roll up and down. This can be

 

 

corrected using the V-HOLD control found on some

 

 

TVs. (This cannot be corrected if the TV does not

 

 

have a V-HOLD control.)

 

 

The counter and tape remaining time readings will be

 

 

incorrect.

 

 

During search, still, or frame-by-frame playback, the

 

 

picture will be distorted, and there may be a loss of

 

 

colour.

 

 

Depending on the type of TV, the top and bottom

 

 

portions of superimposed displays may be cut off

 

 

during NTSC playback.

Retake function does not work during Direct Rec (pg. 11).

Image 50
Contents HR-S9600EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder Connect Video Recorder to TVBack of TV Back of TV Audio in connectors Mains outlet Mains Power CordBefore performing the following procedure, make sure that Go to itemLink screen will appear. Then the Guide Remote control while downloading is10 or If -- appears on the display panel, refer Program number setAuto Set Up results appear on the display panel If both auto channel set and auto clock set have failedTurn on the Recorder TV Auto Power OnLink Functions NexTView LinkPoint PlaybackLoad a Cassette Start PlaybackPlayback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayAccess Video PLUS+ Program Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Enter Pluscode NumberTimer Warning PDC RecordingEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSSelect B.E.S.T. Mode Access Main MenuAccess Mode SET Playback/ Recording According To Tape Charac- teristicsOr press Record on the recorder RecordingPlayback During B.E.S.TDigital TBC/NR Playback Picture AdjustmentManual Tracking Digital 3RActivate Instant Review Looking For Scene You WantActivate Index Search Skip Over UnwantedVariable-Speed Search/ Reverse Play Audio signal during TimeScanTimeScan Normal recorderSpeed SP Speed LP Audio output TimeScanTimeScan Audio Forward Search Play Slow-Motion StillControl Screen Adjust AudioSelecting Sound You Want Recording LevelDuring Playback Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedAutomatic Satellite Programme Recording Satellite Receiver UnitBefore performing the following steps Move the highlight bar pointer to Mode SET byLink indicator lights up and the recorder turns off Pressing %Þ, then press OK or%Remote A/B Code Switching SET Remote ControlRE-SUPPLY Power Remote Con- trol FunctionsSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Operate TVTV Prog +/-,NUMBER keys Satellite Receiver Multi- Brand Remote ControlOperate Satellite Receiver Satellite Tuner Brand CodeSelect Picture Control SET Mode Access Main Menu ScreenAccess Mode SET Screen Minimizing Picture Degradation While EditingEdit From Camcorder Repeat steps 4 6 as necessary Connector Lanc Cable not providedSynchro Editing Edit To Or From Another Video Recorder TV Receiver Player Your recorder Recorder AV1 Select Setting AV2 Select SettingAudio Dubbing Press R.A. Edit Random As- semble EditingPrepare for Editing Start R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. EditNumber Reset the CounterInsert Editing END Insert Editing Engage Insert EditingStart Editing DUBAccess Jlip ID NO. SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Information On J TerminalON-SCREEN Display ENABLE/DISABLEOther Functions On-Screen DisplayPower Save Mode Select Power SaveNext Function Memory Auto SP→LP TimerAuto Timer Repeat Playback Engage RECORD-PAUSE ModeResume Recording RetakeConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionAuto Channel Set Tuner SetPerform Auto Channel SET Is displayed on the screen Screen preset positionsAfter Scan Completed For about 5 seconds, aEnter NEW Channel Information Storing Channels ManuallyInput Channel Close Confirmation ScreenDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Channel SET Screen Access ManualSwitch Stations Select NEW StationTV Station And ID List Station NameTV Station Channel Number Guide Clock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Questions And Answers Ä remain lit on the display panel. Is there Problem?Troubleshooting Timer Recording Won’t stopIndex Front ViewInside View of Front Panel 3 4 5 6 @ # $AV1 IN/OUT Connector enables AV connec Rear ViewDisplay Panel @ #Remote Control TV Muting Button mutes soundRemote Control LCD Fast Forward FF Button same as button on recorder. pgVHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical