JVC SR-L910E Rear Panel, Mark in the Rec/Pause mode is shown in red, Tape counter/time indication

2	CONTROLS AND CONNECTORS
	2-2 Display
	1	6	7	8	9	10	11	12 13	14

2	3	4	5
1Operation mode display		6TIMER indication
Shows the operation modes.		7Lights during timer recording programming/operation.
			REPEAT indication
		8	Lights when the VCR is in the Repeat Record mode.

2 CONTROLS AND CONNECTORS

2-3 Rear Panel

1

CAM SW		ALARM		ALARM		COM			SERIES/CLOCK
OUT		IN		REC OUT			WARNING
	COM		ALARM		TAPE			/REC
			RESET		END OUT			OUT	IN	OUT

2 3 4

						MIC	VIDEO	AUDIO
						IN
							IN	IN
CAM SW	ALARM	ALARM	COM		SERIES/CLOCK	REMOTE
OUT	IN	REC OUT		WARNING
COM	ALARM		TAPE	/REC	IN OUT
	RESET END OUT			OUT
								OUT
							OUT

7	6	5
Connecting the wires to the terminals 8
		1. Hold the button down
		and insert the wire

Playback Recording		Rewind	Fast-	Continuous field
			forward	advance playback
Still	Record-	Rewind	Fast-forward	Reverse

OVERLAP indication Blinks when programs scheduled for timer recording 9overlap.

Timer program number During timer recording, the number of program being

		over the top of the
	2.	terminal.
button		Release the button to
		lock the wire in the
		terminal.

		pause	search	search	playback
2	* (	) mark in the Rec/Pause mode is shown in red.
		Cassette indication
	Lights when a cassette is loaded. Blinks when a
3cassette is being ejected.

recorded blinks. 0When the timer recording ends, this number goes out.

AL (alarm) indication Shown during alarm recording. Blinks when alarm !recording ends.

8

1Power cable Connect the power plug to an AC 220-240 V, 50/60 Hz 2outlet.

8

[SERIES/CLOCK OUT] series recording signal/clock reset signal output terminal Outputs the series recording signals or clock reset

SP/LP indication Shows the VHS standard (SP) mode during recording/ playback. During Timelapse Recording/Playback mode, the SP 4indicator is shown.

	Tape counter/time indication
	• When the power is turned on, the tape counter or
	current time are shown. The display can be selected
	with the [CNT/TIME] button.
	• When the power is turned off, the present time (hour,
5	minute, second) is shown.

Recording/playback mode time display • Shows the recording/playback mode set with the [TIME MODE] button. • When a tape ends in the Record mode, the record time mode indication goes out and the "End" indication blinks (when the <REC REMAIN> menu switch is set to "OFF"). If the <REC REMAIN> menu switch is set to "180S" or "360S", the "End" indication blinks 3 minutes or 6 minutes before the tape ends. • When an problem occurs, the error indication “E-∗∗” blinks. For details, refer to page 43. • During the index search by RS-232C Command, the index number is indicated in 2 digits (00-99). During the index search by FF/REW Button, the index number indicates 01 and 00 only.

	VISS indication
	Shown when the alarm recording start point is index-
	searched. For details, refer to “Index Search” on page
@	42.

LOCK indication #Lights when the operation lock function is activated.

AL REC (alarm recording) indication Lights when the function menu switch <ALARM REC> is $set to “ON”.

SENSOR REC (sensor recording) indication Lights when the function menu switch <SENSOR REC> is set to “ON”.

[MIC IN] mic input connector Connect a microphone with 3.6-mm dia. plug. When signals are input from both the microphone connector and the audio input connector, audio signals are mixed 3and recorded.

[VIDEO IN] video input connector (BNC) Receives composite video signals from a connected 4camera or other video source.

[AUDIO IN] audio input connector (RCA) 5Receives audio signals from a connected audio source.

[AUDIO OUT] audio output connector (RCA) 6Outputs audio signals.

[VIDEO OUT] video output connector (BNC) Outputs composite video signals. Input camera signals (composite video signals) can still be output through this connector even when no power is supplied to the unit 7(Power-Off Video Throughput function).

[REMOTE] remote connector (RCA) Connect the optional RM-G30U remote control.

signals. Select the output signal with the <TERMINAL SEL 1> menu switch.

•Series recording signal output

When the <TERMINAL SEL 1> menu switch is set to “SERIES”, the series recording signal is output.

•Connect to the other VCR series recording signal input terminal. When the tape being recorded in this unit ends, a signal is output from this terminal to the connected VCR.

•Select the signal output timing with the <REC REMAIN> menu switch (tape end, or 3 minutes or 6 minutes before the tape ends).

•Clock reset signal output

When the <TERMINAL SEL 1> menu switch is set to “C.ADJ”, the clock reset signal is output when the internal clock is at AM0:00 and PM0:00. When connected to the [CLOCK IN] terminal of another SR- L910E/EK, this unit’s time can be synchronised with the time on the other VCR if the time difference is within ±30 seconds.

10 11