JVC LPT0616-001A 22 EN, Slow Motion, Pause during playback, Activate frame-by-frame playback

Page 22

22 EN

PLAYBACK/RECORDING ON VHS DECK (cont.)

Playback Features

(VHS deck)

NOTE:

Refer to the illustrations below as you read the following procedures.

	Reverse					Forward
	Reverse	Reverse	Reverse	Slow	Normal	Forward
	Reverse	Reverse	slow	Slow	Normal	Forward
	search	play	slow	motion	play	search
	search	play	motion	motion	play	search
	6 steps		motion	2 steps		7 steps
	6 steps		2 steps	2 steps		7 steps
			2 steps
		1
		2
		1	2	3
		4	5	6	3
		7	8	9	4
					4

0

1	3
2

Clean the video heads using a dry cleaning cassette — TCL-2 — when:

●Rough, poor picture appears while a tape is played back.

●The picture is unclear or no picture appears.

●“USE CLEANING CASSETTE” appears on the screen (only with “O.S.D.” set to “ON” ( pg. 69)).

Still Picture/Frame-By-Frame Playback

1Pause during playback.

Push the JOG dial.

OR

Press 9.

2Activate frame-by-frame playback.

Turn the JOG dial to the right for forward frame-by-frame playback, or to the left for reverse frame-by-frame playback.

OR

Press 9.

OR

Press wor e.

NOTE:

Still picture playback stops automatically after 5 minutes to protect the heads.

To resume normal playback, press 4 or push the JOG dial.

ATTENTION

●Picture may not appear during high-speed search with an LP- recorded tape.

●In the high-speed search, still, slow motion or frame-by-frame playback mode, the picture will be distorted.

●When normal playback resumes from search, still, slow motion or frame-by-frame playback, the picture may jitter vertically momentarily depending on the type of TV being used.

Slow Motion

During playback, turn the JOG dial one click to the left for forward slow motion. To play in reverse slow motion, continue to turn the JOG dial to the left after selecting all the forward direction slow motion modes.

OR

During still picture, press and hold 9 for 2 seconds, then release. Press 9 and release again to return to still picture.

OR

During still picture, press and hold wor e. Release to return to still picture.

NOTES:

●Manual tracking is possible during slow motion playback. ( pg. 25)

●Slow motion playback stops automatically after 5 minutes to protect the heads.

To resume normal playback, press 4.

Image 22

Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display for DV deck Remote Control How To Use Remote Control LCDSituate the recorder Check the contents10 EN Connect the recorder to TVAerial connector 8To connect to a TV with S-VIDEO/AUDIO in connectorsVideo Connection Turn on the recorder Auto Set Up12 EN Select your countryPress rtto select your language code Perform Auto Set UpSelect the language Press rtto select Auto and press OK or e14 EN Perform Preset DownloadPress rtto select CH - and press OK or e Language for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 16 ENAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENNexTView Link TV Auto Power OnVCR Auto Standby Direct Rec 20 EN Basic PlaybackVHS deck Start recording Choose a programmeSet the tape speed Pause/Resume recordingPause during playback 22 ENSlow Motion Activate frame-by-frame playbackIndex Search High-Speed Turbo SearchVariable Speed Search Skip SearchRepeat Playback 24 ENNext Function Memory Activate Repeat PlaybackSoundtrack Selection Adjust the tracking manuallyManual Tracking Override automatic trackingInstant Timer Recording ITR 26 ENSet the counter display Reset the counterTape Remaining Time Press 0000 before starting recording or playbackRetake 28 ENReceiving Stereo and Bilingual Programmes Playback RecordingSelect the DV deck 30 ENDV deck Press DVDV recording indicator turns off 32 EN High-Speed Turbo Search 34 EN Time Code To Record Nicam Bilingual ProgrammesSelect the deck Access the Showview display36 EN Enter the Showview numberCheck the programme data Set the VPS/PDC modeEngage the recorder’s timer mode Satellite Receiver UsersExpress Timer Programming 38 ENEnter the programme date To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the channel position40 EN Enter the programme modeBefore performing the 24 Hour Express Timer Programming Set the programme start/stop time and channelPage 42 EN Select the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screen44 EN Tape DubbingFrom DV to VHS Dubbing An Entire Cassette From VHS to DV Dubbing An Entire Cassette Press DV, then press SP/LP p46 EN From DV to VHSLocate the start point on the VHS deck From VHS to DVPrepare the DV deck for dubbing 48 EN Recorder Video input If the camcorder has no S-VIDEO output connectorPlayer Another Video Recorder 50 ENAnother recorder RecorderPlayer Recorder Output/Input Set Press rt to moveDecoder connector Select SettingVHS F-1 Input Setting Select the input mode for the Video Video connectorVHS Audio Dubbing Audio Dubbing54 EN DV Audio DubbingEnd Audio Dubbing Engage the Audio Dubbing modePress A.DUB 56 EN DV Insert Editing SP mode onlyInsert Editing VHS Insert EditingPrepare the recording cassette Engage the Insert Editing modeAV Insert Editing VHS deck only Start EditingSelect the programme Access the R.A.Edit screen58 EN Insert a VHS or S-VHS cassette and a Mini DV cassetteStart Random Assemble Editing Locate the end pointPrepare the source tape End Random Assemble Editing60 EN Change the remote control codeSet the remote control code Display the codeSet the TV brand code TV Multi-Brand Remote ControlTV PR +/-, TV %+/- Volume, TV Muting, number keys Operate the TVSet the satellite receiver brand code Satellite Receiver Multi-Brand Remote Control62 EN Operate the satellite receiverAbout DV IN/OUT connector Digital printerConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections DecoderConnect the decoder Select the input mode66 EN Set the tunerMake connections AUX in or Tape MonitorSelect the mode Mode SetAccess the Mode Set screen Select the mode settingControl, or press 7 on the recorder Powered back onScreen. Messages appear in the selected language pg Recorder is turned off70 EN VHS Mode SET To record Secam signals, or play back a Mesecam tape To record PAL signals, or play back a PAL or Ntsc tape72 EN Audio-dubbed sound Enables Audio Dubbing laterOriginal recorded sound Full SOUNDOriginal recorded sound and Audio-dubbed sound74 EN Access the Auto Channel Set screenTuner Set Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice 76 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations a 78 ENSet Stations B TV Station And ID List Station NameClock Set Access the Clock Set screen80 EN Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationGuide Program Number Set Showview System Setup82 EN Guide Program NumberPower 84 EN RecordingVHS deck DV deckOther Problems 86 ENPlayback Scan system Signal system88 EN Lines VHS Lines S-VHS Frequency range Hz to 10,000Express Timer Programming Auto Channel Set Auto Set UpConnecting To a Printer Preset Download Random Assemble Editing90 EN Page International telephone Language code Example Francais 03 is selected for BelgiumCountry code