JVC LPT0616-001A Perform Auto Channel Set, View the Confirmation screen, Press OK twice

Page 75

EN 75

1

2

1

2

3

 

4

5

6

3

7

8

9

4

 

 

 

4

0

1

3

2

 

IMPORTANT

●In certain reception conditions, station names may not be stored correctly, and Auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the SHOWVIEW system, the recorder will record a TV programme of a different station. When programming the

timer using the SHOWVIEW system, be sure to check the desired channel is selected correctly ( pg. 36, “SHOWVIEW® Timer Programming”).

●Your video recorder memorizes all detected stations even if

reception of some of them is poor. You can delete those stations with an unacceptable picture ( pg. 77, “Delete A Channel”).

NOTES:

●Fine tuning is performed automatically during Auto Channel Set. If you want to perform tuning manually, refer to page 78.

●If you perform Auto Channel Set when the aerial cable is not connected properly, “SCAN COMPLETED –NO SIGNAL–” appears on the TV screen in step 7. When this happens, make sure of the aerial connection and press OK; Auto Channel Set will take place again.

●If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect.

Select the appropriate TV system for those channels ( pg. 77, “INFORMATION”).

F Perform Auto Channel Set.

Press OK twice.

●You can set up the recorder’s

tuner also by Preset Download ( pg. 14).

●The Auto Set screen appears, and remains on screen while

the recorder searches for

 

 

receivable stations.

 

 

As Auto Channel Set

 

 

progresses, the “q” mark on

Beginning

End

the TV screen moves from

 

 

left to right. Wait until the TV screen as shown in step 7 appears.

G View the Confirmation screen.

After “SCAN COMPLETED” is displayed on the TV screen for about 5 seconds, the Confirmation screen looking like the one to the right appears. The stations your recorder located appear on a Confirmation screen —

channel positions (PR),

channels (CH) and station names (ID –  pg. 79). The blueback screen and the programme currently being broadcast by the blinking station appear alternately for 8 seconds each. To view the next page, use the rtw e button on the remote control.

●The stations located in the selected country appear at the top of the list.

●The Guide Program numbers will also be set automatically during Auto Channel Set.

H Return to the normal screen.

Press MENU.

●Using the Confirmation screen, you can skip or add channel positions, enter station names and perform other operations. Refer to pages 76 – 78 for the procedures.

●Depending on reception conditions, the stations may not be stored in order, and the station names may not be stored correctly.

●For information on scrambled broadcasts, refer to page 77.

Page 74 Page 76
Image 75
Page 74 Page 76
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display for DV deck Remote Control Remote Control LCD How To UseConnect the recorder to TV Check the contents10 EN Situate the recorder8To connect to a TV with S-VIDEO/AUDIO in connectors Aerial connectorVideo Connection Select your country Auto Set Up12 EN Turn on the recorderPress rtto select Auto and press OK or e Perform Auto Set UpSelect the language Press rtto select your language codePerform Preset Download 14 ENPress rtto select CH - and press OK or e Just Clock Language for the on-screen display16 EN Access the Main Menu screenAccess the Country Set screen LanguageMake connections Installing Satellite ControllerSituate the Satellite Controller Attach the Satellite Controller18 EN Setting satellite receivers brand and channelTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 20 ENVHS deck Pause/Resume recording Choose a programmeSet the tape speed Start recordingActivate frame-by-frame playback 22 ENSlow Motion Pause during playbackSkip Search High-Speed Turbo SearchVariable Speed Search Index SearchActivate Repeat Playback 24 ENNext Function Memory Repeat PlaybackOverride automatic tracking Adjust the tracking manuallyManual Tracking Soundtrack Selection26 EN Instant Timer Recording ITRPress 0000 before starting recording or playback Reset the counterTape Remaining Time Set the counter display28 EN RetakeReceiving Stereo and Bilingual Programmes Recording PlaybackPress DV 30 ENDV deck Select the DV deckDV recording indicator turns off 32 EN High-Speed Turbo Search 34 EN To Record Nicam Bilingual Programmes Time CodeEnter the Showview number Access the Showview display36 EN Select the deckSatellite Receiver Users Set the VPS/PDC modeEngage the recorder’s timer mode Check the programme data38 EN Express Timer ProgrammingEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the programme dateSet the programme start/stop time and channel Enter the programme modeBefore performing the 24 Hour Express Timer Programming 40 ENPage 42 EN Overlapping programmes blink on the TV screen Cancel or change programme settingConfirm the overlapping programmes Select the programme to modifyTape Dubbing 44 ENFrom DV to VHS Dubbing An Entire Cassette Press DV, then press SP/LP p From VHS to DV Dubbing An Entire CassetteFrom DV to VHS 46 ENFrom VHS to DV Locate the start point on the VHS deckPrepare the DV deck for dubbing 48 EN If the camcorder has no S-VIDEO output connector Recorder Video inputPlayer 50 EN Another Video RecorderRecorder Another recorderPlayer Recorder Press rt to move Output/Input SetSelect the input mode for the Video Video connector Select SettingVHS F-1 Input Setting Decoder connectorDV Audio Dubbing Audio Dubbing54 EN VHS Audio DubbingEngage the Audio Dubbing mode End Audio DubbingPress A.DUB VHS Insert Editing DV Insert Editing SP mode onlyInsert Editing 56 ENStart Editing Engage the Insert Editing modeAV Insert Editing VHS deck only Prepare the recording cassetteInsert a VHS or S-VHS cassette and a Mini DV cassette Access the R.A.Edit screen58 EN Select the programmeEnd Random Assemble Editing Locate the end pointPrepare the source tape Start Random Assemble EditingDisplay the code Change the remote control codeSet the remote control code 60 ENOperate the TV TV Multi-Brand Remote ControlTV PR +/-, TV %+/- Volume, TV Muting, number keys Set the TV brand codeOperate the satellite receiver Satellite Receiver Multi-Brand Remote Control62 EN Set the satellite receiver brand codeDigital printer About DV IN/OUT connectorSimple Connections Connecting To a Satellite ReceiverDecoder Perfect ConnectionsSet the tuner Select the input mode66 EN Connect the decoderAUX in or Tape Monitor Make connectionsSelect the mode setting Mode SetAccess the Mode Set screen Select the modeRecorder is turned off Powered back onScreen. Messages appear in the selected language  pg Control, or press 7 on the recorder70 EN VHS Mode SET To record PAL signals, or play back a PAL or Ntsc tape To record Secam signals, or play back a Mesecam tape72 EN Full SOUNDOriginal recorded sound and Audio-dubbed sound Enables Audio Dubbing laterOriginal recorded sound Audio-dubbed soundAuto Channel Set Access the Auto Channel Set screenTuner Set 74 ENPerform Auto Channel Set View the Confirmation screenPress OK twice Manual Channel Set 76 ENDelete a Channel When Receiving a Scrambled Broadcast78 EN Set Stations aSet Stations B Station Name TV Station And ID ListAccess the Clock Set screen Clock Set80 EN Start the clock operation Set the date and timeSet Just Clock Set the source channel position for clock dataGuide Program Number Showview System Setup82 EN Guide Program Number SetPower Recording 84 ENDV deck VHS deck86 EN Other ProblemsPlayback Lines VHS Lines S-VHS Frequency range Hz to 10,000 Signal system88 EN Scan systemPreset Download Random Assemble Editing Auto Channel Set Auto Set UpConnecting To a Printer Express Timer Programming90 EN Page Example Francais 03 is selected for Belgium International telephone Language codeCountry code
Top Page Image Contents