JVC LPT0616-001A specifications 86 EN, Other Problems

Page 86

86 EN			TROUBLESHOOTING (cont.)
OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Whistling or howling is heard from the	● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 76).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Turn off the recorder once and connect
	recorder’s memory.	to the recorder when Auto Set Up was	the TV aerial cable to the recorder
		performed.	properly, then turn on the recorder again.
			The recorder will try Auto Set Up again
			( pg. 12).
		● The fully-wired 21-pin SCART cable was	Turn off the recorder once and connect
		not connected between TV and the	the fully-wired 21-pin SCART cable to the
		recorder when Preset Download was	recorder properly, then turn on the
		performed.	recorder again. Then perform Preset
			Download again ( pg. 14).

6.	The remote control won’t operate the	● The remote control brand setting is	Re-set the remote control to the correct
	TV or satellite receiver.	incorrect.	brand. ( pg. 61, 62)

7.	No picture appears when you connect		Turn off the recorder or the connected
	a device to DV IN/OUT connector.		appliance once, then turn it on again.

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 86

Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display for DV deck Remote Control How To Use Remote Control LCDSituate the recorder Check the contents10 EN Connect the recorder to TVVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectorsAerial connector Turn on the recorder Auto Set Up12 EN Select your countryPress rtto select your language code Perform Auto Set UpSelect the language Press rtto select Auto and press OK or ePress rtto select CH - and press OK or e Perform Preset Download14 EN Language for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 16 ENAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link VHS deck Basic Playback20 EN Start recording Choose a programmeSet the tape speed Pause/Resume recordingPause during playback 22 ENSlow Motion Activate frame-by-frame playbackIndex Search High-Speed Turbo SearchVariable Speed Search Skip SearchRepeat Playback 24 ENNext Function Memory Activate Repeat PlaybackSoundtrack Selection Adjust the tracking manuallyManual Tracking Override automatic trackingInstant Timer Recording ITR 26 ENSet the counter display Reset the counterTape Remaining Time Press 0000 before starting recording or playbackReceiving Stereo and Bilingual Programmes 28 ENRetake Playback RecordingSelect the DV deck 30 ENDV deck Press DVDV recording indicator turns off 32 EN High-Speed Turbo Search 34 EN Time Code To Record Nicam Bilingual ProgrammesSelect the deck Access the Showview display36 EN Enter the Showview numberCheck the programme data Set the VPS/PDC modeEngage the recorder’s timer mode Satellite Receiver UsersExpress Timer Programming 38 ENEnter the programme date To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the channel position40 EN Enter the programme modeBefore performing the 24 Hour Express Timer Programming Set the programme start/stop time and channelPage 42 EN Select the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenFrom DV to VHS Dubbing An Entire Cassette Tape Dubbing44 EN From VHS to DV Dubbing An Entire Cassette Press DV, then press SP/LP p46 EN From DV to VHSPrepare the DV deck for dubbing From VHS to DVLocate the start point on the VHS deck 48 EN Player If the camcorder has no S-VIDEO output connectorRecorder Video input Another Video Recorder 50 ENPlayer Recorder RecorderAnother recorder Output/Input Set Press rt to moveDecoder connector Select SettingVHS F-1 Input Setting Select the input mode for the Video Video connectorVHS Audio Dubbing Audio Dubbing54 EN DV Audio DubbingPress A.DUB Engage the Audio Dubbing modeEnd Audio Dubbing 56 EN DV Insert Editing SP mode onlyInsert Editing VHS Insert EditingPrepare the recording cassette Engage the Insert Editing modeAV Insert Editing VHS deck only Start EditingSelect the programme Access the R.A.Edit screen58 EN Insert a VHS or S-VHS cassette and a Mini DV cassetteStart Random Assemble Editing Locate the end pointPrepare the source tape End Random Assemble Editing60 EN Change the remote control codeSet the remote control code Display the codeSet the TV brand code TV Multi-Brand Remote ControlTV PR +/-, TV %+/- Volume, TV Muting, number keys Operate the TVSet the satellite receiver brand code Satellite Receiver Multi-Brand Remote Control62 EN Operate the satellite receiverAbout DV IN/OUT connector Digital printerConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections DecoderConnect the decoder Select the input mode66 EN Set the tunerMake connections AUX in or Tape MonitorSelect the mode Mode SetAccess the Mode Set screen Select the mode settingControl, or press 7 on the recorder Powered back onScreen. Messages appear in the selected language pg Recorder is turned off70 EN VHS Mode SET 72 EN To record PAL signals, or play back a PAL or Ntsc tapeTo record Secam signals, or play back a Mesecam tape Audio-dubbed sound Enables Audio Dubbing laterOriginal recorded sound Full SOUNDOriginal recorded sound and Audio-dubbed sound74 EN Access the Auto Channel Set screenTuner Set Auto Channel SetPress OK twice Perform Auto Channel SetView the Confirmation screen 76 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations B 78 ENSet Stations a TV Station And ID List Station Name80 EN Access the Clock Set screenClock Set Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationGuide Program Number Set Showview System Setup82 EN Guide Program NumberPower 84 EN RecordingVHS deck DV deckOther Problems 86 ENPlayback Scan system Signal system88 EN Lines VHS Lines S-VHS Frequency range Hz to 10,000Express Timer Programming Auto Channel Set Auto Set UpConnecting To a Printer Preset Download Random Assemble Editing90 EN Page Country code Example Francais 03 is selected for BelgiumInternational telephone Language code