JVC LPT0678-001A 40 EN, Enter the programme mode, Set the programme start/stop time and channel

Page 40

40 EN

TIMER RECORDING (cont.)

24 Hour Express Timer Programming

Before performing the 24 Hour Express Timer Programming:

●Make sure that the recorder’s built-in clock is set properly.

●Select the deck.

●Set the tape speed.

●For the VHS deck:

Insert a VHS (or S-VHS) cassette with the record safety tab intact.

For the DV deck:

Insert a Mini DV cassette with the erase protection switch set to “REC”.

You can programme a timer recording that starts within 24 hours using the JOG dial on the recorder.

A Enter the programme mode.

Press 24H EXPRESS # on the recorder. The start time indicator ( ) starts blinking on the front display panel.

●The current tape speed and VPS/PDC setting appear on the front display panel, but it is impossible to change the setting.

You can only change the setting after programming ( pg. 42).

B Set the programme start/stop time and channel.

Turn the JOG dial to the left or right to set the time you want recording to start.

●One click stop of the JOG dial changes the time in 5-minute intervals.

1

3

2

Push the JOG dial. The stop time indicator ( ) starts blinking on the front display panel. Turn the JOG dial to the left or right to set the time you want recording to stop.

Push the JOG dial. Turn the JOG dial to the left or right to select the channel you wish to record.

●You can cancel the setting at any time by pressing and holding the JOG dial for more than 3 seconds or pressing & on the remote control. Repeat the step 2.

C Engage the recorder’s timer mode.

Press 24H EXPRESS #. The recorder turns off automatically and “#” appears on the front display panel.

●To disengage the timer mode, press # (TIMER) or 24H EXPRESS # again.

Image 40

Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display for VHS deck On the tape BeginningEndRemote Control How To Use Remote Control LCDCheck the contents 10 ENSituate the recorder Connect the recorder to TVAerial connector 8To connect to a TV with S-VIDEO/AUDIO in connectorsVideo Connection Auto Set Up 12 ENTurn on the recorder Select your countryPerform Auto Set Up Select the languagePress rt to select your language code Press rt to select Auto and press OK or e14 EN Perform Preset DownloadPress rt to select CH - and press OK or e Just Clock Language for the on-screen display pg , Just Clock Access the Main Menu screen Access the Country Set screenLanguage 16 ENInstalling Satellite Controller Situate the Satellite ControllerAttach the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENNexTView Link TV Auto Power OnVCR Auto Standby Direct Rec 20 EN Basic PlaybackVHS deck Choose a programme Set the tape speedStart recording Pause/Resume recording22 EN Slow MotionPause during playback Activate frame-by-frame playbackHigh-Speed Turbo Search Variable Speed SearchIndex Search Skip Search24 EN Next Function MemoryRepeat Playback Activate Repeat PlaybackAdjust the tracking manually Manual TrackingSoundtrack Selection Override automatic trackingInstant Timer Recording ITR 26 ENReset the counter Tape Remaining TimeSet the counter display Press 0000 before starting recording or playbackRetake 28 ENReceiving Stereo and Bilingual Programmes Playback Recording30 EN DV deckSelect the DV deck Press DVDV recording indicator turns off 32 EN For forward high-speed search During playback, turn the JOG dial quickly to the rightSearch, or 3 for reverse high-speed search During playback or still, press 5 for forward high-speed34 EN Time Code See Audio REC onAccess the Showview display 36 ENSelect the deck Enter the Showview numberSet the VPS/PDC mode Engage the recorder’s timer modeCheck the programme data Satellite Receiver UsersExpress Timer Programming 38 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the programme date Enter the channel positionEnter the programme mode Before performing the 24 Hour Express Timer Programming40 EN Set the programme start/stop time and channelPage 42 EN Cancel or change programme setting Confirm the overlapping programmesSelect the programme to modify Overlapping programmes blink on the TV screen44 EN Tape DubbingFrom DV to VHS Dubbing An Entire Cassette From VHS to DV Dubbing An Entire Cassette Dubbing direction indicator VHS lightsPress DV, then press SP/LP p 46 EN From DV to VHSVHS playback indicator and DV recording indicator light From VHS to DVLocate the start point on the VHS deck Prepare the DV deck for dubbing48 EN If the camcorder has no S-VIDEO output connector Simultaneous DubbingRecorder Video input PlayerAnother Video Recorder 50 ENAnother recorder RecorderPlayer Recorder Output/Input Set Press rt to moveSelect Setting VHS F-1 Input SettingDecoder connector Select the input mode for the Video Video connectorAudio Dubbing 54 ENVHS Audio Dubbing DV Audio DubbingEnd Audio Dubbing Engage the Audio Dubbing modePress A.DUB DV Insert Editing SP mode only Insert Editing56 EN VHS Insert EditingEngage the Insert Editing mode AV Insert Editing VHS deck onlyPrepare the recording cassette Start EditingAccess the R.A.Edit screen 58 ENSelect the programme Insert a VHS or S-VHS cassette and a Mini DV cassetteLocate the end point Prepare the source tapeStart Random Assemble Editing End Random Assemble EditingChange the remote control code Set the remote control code60 EN Display the codeTV Multi-Brand Remote Control TV PR +/-, TV %+/- Volume, TV Muting, number keysSet the TV brand code Operate the TVSatellite Receiver Multi-Brand Remote Control 62 ENSet the satellite receiver brand code Operate the satellite receiverTo DV in connector About DV IN/OUT connectorDigital printer Aerial ConnectorAerial Pin Scart connector Mains outletSimple Connections Outdoor unit Satellite cableAerial connector Outdoor unit Satellite cable Perfect ConnectionsPin Scart DecoderSelect the input mode 66 ENConnect the decoder Set the tunerMake connections FM tuner CD player Stereo amplifierAUX in or Tape Monitor Speaker TelevisionMode Set Access the Mode Set screenSelect the mode Select the mode settingPowered back on Default setting is bold in the table belowScreen. Messages appear in the selected language pg Control, or press 7 on the recorder70 EN VHS Mode SET To record Secam signals, or play back a Mesecam tape To record PAL signals, or play back a PAL or Ntsc tape72 EN Enables Audio Dubbing later Original recorded soundAudio-dubbed sound Full SOUNDOriginal recorded sound and Audio-dubbed soundAccess the Auto Channel Set screen Tuner Set74 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice TV screen moves from76 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations a 78 ENSet Stations B TV Station And ID List RTBF1 orClock Set Access the Clock Set screen80 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operationShowview System Setup 82 ENGuide Program Number Set Guide Program NumberNo power is supplied to the recorder Connect the mains power cord84 EN VHS deck DV deck86 EN Turn off the recorder once and connectNot connected between TV Turn off the recorder or the connectedPlayback 88 EN Auto Channel Set Auto Set Up Connecting To a PrinterExpress Timer Programming Preset Download Random Assemble Editing90 EN Page International telephone Language code Example Francais 03 is selected for BelgiumCountry code