JVC LPT0678-001A specifications 84 EN

Page 84

84 EN			TROUBLESHOOTING (cont.)
RECORDING
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Recording cannot be started.	● For the VHS deck
		There is no cassette loaded, or the	Insert a VHS (or S-VHS) cassette, or using
		cassette loaded has had its record safety	adhesive tape, cover the hole where the
		tab removed.	tab was removed.
		● For the DV deck
		There is no cassette loaded, or the	Insert a Mini DV cassette, or set the erase
		cassette loaded has had its erase	protection switch set to “REC”.
		protection switch set to “SAVE”.

2.	TV broadcasts cannot be recorded.	● “L-1”, “L-2”, “F-1” or “SAT” has been	Set to the desired channel.
		selected as the input mode.

3.	Tape-to-tape editing is not possible.	● The source (another video recorder,	Confirm that the source is properly
		camcorder) has not been properly	connected.
		connected.
		● All necessary power switches have not	Confirm that all units’ power switches are
		been turned on.	turned on.
		● The input mode is not correct.	Set the input mode to “L-1”, “L-2” or
			“F-1”.

4.	Camcorder recording is not possible.	● The camcorder has not been properly	Confirm that the camcorder is properly
		connected.	connected.
		● The input mode is not correct.	Set the input mode to “L-1”, “L-2” or
			“F-1”.

5.	“[” on the front display panel won’t	● The end of the tape was reached during	The programme may not have been
	stop blinking.	recording.	recorded in its entirety. Next time make
			sure you have enough time on the tape to
			record the entire programme.

6.	Audio dubbing is not possible.	For the DV deck
		● “SOUND MODE” had been set to	Set “SOUND MODE” to “12BIT” at the
		“16BIT” at the original recording.	original recording. ( pg. 73)
		● The tape speed had been set to LP at the	Set the tape speed to SP at the original
		original recording.	recording.

7.	Monitoring the audio-dubbed sound is	● This is normal.	Set “12BIT MODE” to “SOUND 2” or
	not possible during audio dubbing		monitor the sound using the connected
	using the DV deck.		devices.

8.	The programmed memory of Random	● The memory backup time has expired.	Perform Random Assemble Editing again.
	Assemble Editing is disappeared.		( pg. 58)

9.	When performing Normal Dubbing,	● This is normal.	Locate the start point a little before the
	the beginning of the dubbing start		point where you want to start dubbing.
	point is not dubbed.		( pg. 46, 47)

Image 84

Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display for VHS deck On the tape BeginningEndRemote Control How To Use Remote Control LCDCheck the contents 10 ENSituate the recorder Connect the recorder to TV8To connect to a TV with S-VIDEO/AUDIO in connectors Aerial connectorVideo Connection Auto Set Up 12 ENTurn on the recorder Select your countryPerform Auto Set Up Select the languagePress rt to select your language code Press rt to select Auto and press OK or ePerform Preset Download 14 ENPress rt to select CH - and press OK or e Language for the on-screen display Just Clock pg , Just Clock Access the Main Menu screen Access the Country Set screenLanguage 16 ENInstalling Satellite Controller Situate the Satellite ControllerAttach the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 20 ENVHS deck Choose a programme Set the tape speedStart recording Pause/Resume recording22 EN Slow MotionPause during playback Activate frame-by-frame playbackHigh-Speed Turbo Search Variable Speed SearchIndex Search Skip Search24 EN Next Function MemoryRepeat Playback Activate Repeat PlaybackAdjust the tracking manually Manual TrackingSoundtrack Selection Override automatic trackingInstant Timer Recording ITR 26 ENReset the counter Tape Remaining TimeSet the counter display Press 0000 before starting recording or playback28 EN RetakeReceiving Stereo and Bilingual Programmes Playback Recording30 EN DV deckSelect the DV deck Press DVDV recording indicator turns off 32 EN For forward high-speed search During playback, turn the JOG dial quickly to the rightSearch, or 3 for reverse high-speed search During playback or still, press 5 for forward high-speed34 EN Time Code See Audio REC onAccess the Showview display 36 ENSelect the deck Enter the Showview numberSet the VPS/PDC mode Engage the recorder’s timer modeCheck the programme data Satellite Receiver UsersExpress Timer Programming 38 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the programme date Enter the channel positionEnter the programme mode Before performing the 24 Hour Express Timer Programming40 EN Set the programme start/stop time and channelPage 42 EN Cancel or change programme setting Confirm the overlapping programmesSelect the programme to modify Overlapping programmes blink on the TV screenTape Dubbing 44 ENFrom DV to VHS Dubbing An Entire Cassette Dubbing direction indicator VHS lights From VHS to DV Dubbing An Entire CassettePress DV, then press SP/LP p 46 EN From DV to VHSVHS playback indicator and DV recording indicator light From VHS to DVLocate the start point on the VHS deck Prepare the DV deck for dubbing48 EN If the camcorder has no S-VIDEO output connector Simultaneous DubbingRecorder Video input PlayerAnother Video Recorder 50 ENRecorder Another recorderPlayer Recorder Output/Input Set Press rt to moveSelect Setting VHS F-1 Input SettingDecoder connector Select the input mode for the Video Video connectorAudio Dubbing 54 ENVHS Audio Dubbing DV Audio DubbingEngage the Audio Dubbing mode End Audio DubbingPress A.DUB DV Insert Editing SP mode only Insert Editing56 EN VHS Insert EditingEngage the Insert Editing mode AV Insert Editing VHS deck onlyPrepare the recording cassette Start EditingAccess the R.A.Edit screen 58 ENSelect the programme Insert a VHS or S-VHS cassette and a Mini DV cassetteLocate the end point Prepare the source tapeStart Random Assemble Editing End Random Assemble EditingChange the remote control code Set the remote control code60 EN Display the codeTV Multi-Brand Remote Control TV PR +/-, TV %+/- Volume, TV Muting, number keysSet the TV brand code Operate the TVSatellite Receiver Multi-Brand Remote Control 62 ENSet the satellite receiver brand code Operate the satellite receiverAbout DV IN/OUT connector To DV in connectorDigital printer Aerial ConnectorAerial Pin Scart connector Mains outletSimple Connections Outdoor unit Satellite cableAerial connector Outdoor unit Satellite cable Perfect ConnectionsPin Scart DecoderSelect the input mode 66 ENConnect the decoder Set the tunerMake connections FM tuner CD player Stereo amplifierAUX in or Tape Monitor Speaker TelevisionMode Set Access the Mode Set screenSelect the mode Select the mode settingPowered back on Default setting is bold in the table belowScreen. Messages appear in the selected language pg Control, or press 7 on the recorder70 EN VHS Mode SET To record PAL signals, or play back a PAL or Ntsc tape To record Secam signals, or play back a Mesecam tape72 EN Enables Audio Dubbing later Original recorded soundAudio-dubbed sound Full SOUNDOriginal recorded sound and Audio-dubbed soundAccess the Auto Channel Set screen Tuner Set74 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice TV screen moves from76 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel78 EN Set Stations aSet Stations B TV Station And ID List RTBF1 orAccess the Clock Set screen Clock Set80 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operationShowview System Setup 82 ENGuide Program Number Set Guide Program NumberNo power is supplied to the recorder Connect the mains power cord84 EN VHS deck DV deck86 EN Turn off the recorder once and connectNot connected between TV Turn off the recorder or the connectedPlayback 88 EN Auto Channel Set Auto Set Up Connecting To a PrinterExpress Timer Programming Preset Download Random Assemble Editing90 EN Page Example Francais 03 is selected for Belgium International telephone Language codeCountry code