JVC LPT0678-001A specifications VHS Mode SET

Page 71

EN 71

VHS MODE SET (cont.)

* The default setting is bold in the table below.

8 DIGITAL 3R

When this function is set to “ON”, the Digital 3R picture system applies edge

ON

correction to the luminance signal to enhance detail.

OFF

NOTES:

 

 

Normally it is recommended to keep “DIGITAL 3R” set to “ON”.

 

Depending on the type of tape being used, picture quality may be better with “DIGITAL

 

3R” set to “OFF”.

 

If you use the recorder as the source player for editing, be sure to set “DIGITAL 3R” to

 

“OFF” before starting.

 

 

8 S-VHS

Your recorder can record in S-VHS (Super VHS), S-VHS ET or VHS.

ON

To record in S-VHS:

OFF

Set “S-VHS” to “ON”. Then, insert a cassette marked “S-VHS”. The S-VHS indicator

 

 

lights up on the front display panel.

 

The S-VHS recording mode is selected.

 

To record in S-VHS ET on a VHS cassette:

 

Set “S-VHS ET” to “ON”. ( See below.) Then, insert a cassette marked “VHS”.

 

The S-VHS indicator lights up on the front display panel.

 

To record in VHS:

 

Insert a cassette marked “VHS”.

 

Set “S-VHS ET” to “OFF”. ( See below.)

 

To record in VHS on an S-VHS cassette:

 

Insert a cassette marked “S-VHS”. The S-VHS indicator lights up on the front

 

display panel. Then, set “S-VHS” to “OFF”. The S-VHS indicator goes off.

 

The VHS recording mode is selected.

 

NOTE:

 

When playing back a tape that has been recorded in S-VHS or S-VHS ET, the S-VHS indicator

 

lights up on the front display panel regardless of the “S-VHS” mode setting.

 

 

8 S-VHS ET

You can record in SP mode on VHS cassettes with S-VHS picture quality. Tapes

ON

recorded using this function can be played back on a recorder equipped with the

OFF

S-VHS ET function.

 

When this function is set to “ON”, the S-VHS indicator lights up on the front

 

display panel.

 

NOTES:

 

You can activate the S-VHS ET function only before you start recording on a VHS cassette.

 

Before recording, make sure that “B.E.S.T.” is set to “ON”. ( pg. 70)

 

You cannot activate the S-VHS ET function ...

 

... while recording is in progress.

 

... while timer-recording or Instant Timer Recording ( pg. 26, 34) is in progress.

 

... while B.E.S.T. ( pg. 29) is in progress.

 

The S-VHS ET function does not work ...

 

... with S-VHS cassettes.

 

... with recordings in LP mode.

 

To keep the highest quality recording and playback pictures over a long period of time,

 

S-VHS recording on S-VHS cassettes is recommended.

 

Use of high grade tapes is recommended for S-VHS ET recordings. On some tapes, picture

 

quality will not improve even if the S-VHS ET function is used. Check the recording quality

 

before you start important recordings.

 

You can play back a tape recorded using the S-VHS ET function on most of S-VHS recorders

 

and of VHS recorders equipped with SQPB (S-VHS QUASI PLAYBACK) function. (Notice

 

some recorders are not compatible with the S-VHS ET function.)

 

While playing back a tape recorded using the S-VHS ET function on some recorders, noise

 

may appear. (If playback picture becomes blurred or interrupted, use a cleaning cassette.)

 

In the high-speed search, still, slow-motion or frame-by-frame playback modes ( pg. 22),

 

noise may appear. If these modes are performed frequently on a tape recorded using the

 

S-VHS ET function, the tape may be damaged and the picture may be deteriorated.

 

 

Image 71
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel On the tape BeginningEnd ON-SCREEN Display for VHS deckRemote Control Remote Control LCD How To UseConnect the recorder to TV Check the contents10 EN Situate the recorderVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectorsAerial connector Select your country Auto Set Up12 EN Turn on the recorderPress rt to select Auto and press OK or e Perform Auto Set UpSelect the language Press rt to select your language codePress rt to select CH - and press OK or e Perform Preset Download14 EN  pg , Just Clock Language for the on-screen displayJust Clock 16 EN Access the Main Menu screenAccess the Country Set screen LanguageMake connections Installing Satellite ControllerSituate the Satellite Controller Attach the Satellite Controller18 EN Setting satellite receivers brand and channelVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link VHS deck Basic Playback20 EN Pause/Resume recording Choose a programmeSet the tape speed Start recordingActivate frame-by-frame playback 22 ENSlow Motion Pause during playbackSkip Search High-Speed Turbo SearchVariable Speed Search Index SearchActivate Repeat Playback 24 ENNext Function Memory Repeat PlaybackOverride automatic tracking Adjust the tracking manuallyManual Tracking Soundtrack Selection26 EN Instant Timer Recording ITRPress 0000 before starting recording or playback Reset the counterTape Remaining Time Set the counter displayReceiving Stereo and Bilingual Programmes 28 ENRetake Recording PlaybackPress DV 30 ENDV deck Select the DV deckDV recording indicator turns off 32 EN During playback or still, press 5 for forward high-speed For forward high-speed searchDuring playback, turn the JOG dial quickly to the right Search, or 3 for reverse high-speed search34 EN See Audio REC on Time CodeEnter the Showview number Access the Showview display36 EN Select the deckSatellite Receiver Users Set the VPS/PDC modeEngage the recorder’s timer mode Check the programme data38 EN Express Timer ProgrammingEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the programme dateSet the programme start/stop time and channel Enter the programme modeBefore performing the 24 Hour Express Timer Programming 40 ENPage 42 EN Overlapping programmes blink on the TV screen Cancel or change programme settingConfirm the overlapping programmes Select the programme to modifyFrom DV to VHS Dubbing An Entire Cassette Tape Dubbing44 EN Press DV, then press SP/LP p Dubbing direction indicator VHS lightsFrom VHS to DV Dubbing An Entire Cassette From DV to VHS 46 ENPrepare the DV deck for dubbing VHS playback indicator and DV recording indicator lightFrom VHS to DV Locate the start point on the VHS deck48 EN Player If the camcorder has no S-VIDEO output connectorSimultaneous Dubbing Recorder Video input50 EN Another Video RecorderPlayer Recorder RecorderAnother recorder Press rt to move Output/Input SetSelect the input mode for the Video Video connector Select SettingVHS F-1 Input Setting Decoder connectorDV Audio Dubbing Audio Dubbing54 EN VHS Audio DubbingPress A.DUB Engage the Audio Dubbing modeEnd Audio Dubbing VHS Insert Editing DV Insert Editing SP mode onlyInsert Editing 56 ENStart Editing Engage the Insert Editing modeAV Insert Editing VHS deck only Prepare the recording cassetteInsert a VHS or S-VHS cassette and a Mini DV cassette Access the R.A.Edit screen58 EN Select the programmeEnd Random Assemble Editing Locate the end pointPrepare the source tape Start Random Assemble EditingDisplay the code Change the remote control codeSet the remote control code 60 ENOperate the TV TV Multi-Brand Remote ControlTV PR +/-, TV %+/- Volume, TV Muting, number keys Set the TV brand codeOperate the satellite receiver Satellite Receiver Multi-Brand Remote Control62 EN Set the satellite receiver brand codeDigital printer About DV IN/OUT connectorTo DV in connector Outdoor unit Satellite cable Aerial ConnectorAerialPin Scart connector Mains outlet Simple ConnectionsDecoder Aerial connector Outdoor unit Satellite cablePerfect Connections Pin ScartSet the tuner Select the input mode66 EN Connect the decoderSpeaker Television Make connectionsFM tuner CD player Stereo amplifier AUX in or Tape MonitorSelect the mode setting Mode SetAccess the Mode Set screen Select the modeControl, or press 7 on the recorder Powered back onDefault setting is bold in the table below Screen. Messages appear in the selected language  pg70 EN VHS Mode SET 72 EN To record PAL signals, or play back a PAL or Ntsc tapeTo record Secam signals, or play back a Mesecam tape Full SOUNDOriginal recorded sound and Audio-dubbed sound Enables Audio Dubbing laterOriginal recorded sound Audio-dubbed soundAuto Channel Set Access the Auto Channel Set screenTuner Set 74 ENTV screen moves from Perform Auto Channel SetView the Confirmation screen Press OK twiceManual Channel Set 76 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations B 78 ENSet Stations a RTBF1 or TV Station And ID List80 EN Access the Clock Set screenClock Set Start the clock operation Set the date and timeSet Just Clock Set the source channel position for clock dataGuide Program Number Showview System Setup82 EN Guide Program Number SetConnect the mains power cord No power is supplied to the recorder84 EN DV deck VHS deckTurn off the recorder or the connected 86 ENTurn off the recorder once and connect Not connected between TVPlayback 88 EN Preset Download Random Assemble Editing Auto Channel Set Auto Set UpConnecting To a Printer Express Timer Programming90 EN Page Country code Example Francais 03 is selected for BelgiumInternational telephone Language code