JVC DR-MH20SUJ Auto Clock Set/Auto Tuner Set, During Auto Clock Set, During Auto Channel Set

Filename [DR-MH30UJ_04Name.fm]
DR-MH30UJ_00.book Page 20 Monday, July 12, 2004 3:17 PM	Masterpage:Left0

20 EN INITIAL SETTINGS

1 Connect the antenna cable to the unit. ( pg. 19) Then connect

Plug & Play Setthe AC power cord to an AC outlet. Do not turn on the unit. The clock and tuner channels will be set automatically.

Auto Clock Set/Auto Tuner Set	● “LOADING” blinks on the front display panel when the AC plug of the
	AC power cord is connected into an AC outlet and it takes
This unit sets the clock and tuner channels automatically when AC	approximately 50 seconds for the unit to be turned on. This is not a
power cord is first connected to an AC outlet. The antenna cable	malfunction.
must be connected for the Plug & Play setting.	NOTES:
The time and date can be set automatically by the clock setting	● Auto Clock Set is performed first.
data transmitted from one of the regular TV broadcast channels.	“AUTO” blinks on the front display panel during Auto Clock Set.
We call this TV channel the “host channel” and it is a PBS channel	● Auto Channel Set is performed next. Auto Channel Set scans all the
in your area.	channels that are receivable by your unit. During Auto Channel Set,
	the channel numbers are displayed as they are scanned and set.
ATTENTION:	● When Plug & Play setting has been complete successfully, the
● If you use a cable box, Plug&Play will not function; set the clock	correct clock time is displayed. If you perform Plug & Play setting
and tuner channels separately. ( pg. 22 – 23)	successfully, there is no need to perform “Clock Set” ( pg. 22) and
● Depending on areas or reception conditions, the unit may not	“Tuner Set” ( pg. 23). If, however, you want to add or delete
receive the Auto clock setting data from the PBS channel. If this	channels, refer to “Manual Channel Set” ( pg. 23).
function is taking a considerable amount of time, it may be	During Auto Clock Set
necessary to perform the Semiauto or Manual Clock Set
	“AUTO” blinks.
procedure.

1

During Auto Channel Set

The channel numbers are displayed and “AUTO” blinks as they are scanned and set.

INFORMATION

●If “AUTO CLOCK” is set to “ON” ( pg. 22), the clock will be adjusted automatically by the host channel every hour (except 11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming PBS channel clock setting data. (This automatic clock adjustment can only be performed when the unit is turned off. The clock will be adjusted just on these hours — on the time displayed on the front display panel, not on the actual real time.) The default setting of “AUTO CLOCK” is “ON”. ( pg. 22)

●If the memory backup fails, because a power outage occurs or because the AC power cord is unplugged, Plug & Play will be performed when power is restored to the unit.

What to do if Plug & Play setting failed

●If an incorrect time is displayed on the front display panel, you may be receiving the clock setting data of a PBS channel from an adjacent time zone, or an incorrect PBS channel from a cable TV system. In this case, perform “Semiauto Clock Set” ( pg. 22) or “Manual Clock Set” ( pg. 22).

●If “– –:– –” appears on the front display panel, your antenna cable may not be connected to the unit or there may not be a Host PBS signal available in your area. Ensure that the antenna cable is connected correctly. Then turn on and off the unit; the Plug & Play setting will be automatically reactivated. If Plug & Play setting is not performed though the antenna cable is connected correctly, perform “Manual Clock Set” ( pg. 22) and “Auto Channel Set” ( pg. 23) or “Manual Channel Set” ( pg. 23).

Plug&Play Completed

The current time is displayed.

●If an incorrect clock time or “– –:– –” appears on the front display panel, see “What to do if Plug & Play setting failed” ( pg. 20).

Page 20

Monday, 12 July 2004 14:10