JVC DR-MH30SUJ manual For cable box, If the cable box’s channel does, For DBS receiver, Above

Filename [DR-MH30UJ_04Name.fm]
DR-MH30UJ_00.book Page 25 Monday, July 12, 2004 3:17 PM							Masterpage:Right+
						INITIAL SETTINGS EN 25
7 Select the output channel.		8 For cable box
Your selection depends on how the cable box and/or DBS receiver		If the cable box’s channel changes to 9, setting is complete.
is connected to your unit.		Press ENTER and “CABLE BOX				INITIAL SET UP > CABLE BOX SET
● If the cable box or DBS receiver is connected to your unit’s		CONTROL IS ON” appears on the
ANTENNA IN connector on the rear panel, press rt to select the		screen for about 5 seconds, then
channel number representing the cable box’s output (CH2 – CH9),		the screen in step 5 appears.
then press ENTER.							DID YOUR CABLE BOX CHANGE TO CHANNEL 09?
		If the cable box’s channel does
● If the cable box or DBS receiver is connected to your unit’s							YES		N O
		not change to 9;
AUDIO/VIDEO Input connectors on the front panel, press rt to
		A Press w e to select “NO”, then
select “F-1”, then press ENTER.						SET UP	ENTER SELECT WITH [		] THEN PRESS [ENTER]
		press ENTER.				EXIT	PRESS [SET UP] TO EXIT
● If the cable box or DBS receiver is connected to your unit’s							SELECT
AUDIO/VIDEO INPUT connectors on the rear panel, press rt to		B Repeat steps 8 – 9 until the cable box’s channel changes to 9
select “L-1” or “L-2”, then press ENTER.		by entering another code.
● If you do not use a cable box or DBS receiver, press rt to select		C If the channel does not change after going through all the code
“OFF”, then press ENTER.		numbers listed for your model of cable box, then try all the other
8 Press rt to select “CABLE BOX BRAND” or “DBS RECEIVER		numbers.
BRAND”, then press ENTER. Press rt to select the brand code		8 For DBS receiver
		If the DBS receiver’s channel
from the following list, then press ENTER.						INITIAL SET UP > DBS RECEIVER SET
		changes to the channel listed
9 Press rt to select “TEST MODE”, then press ENTER.
		below for your brand, setting is
		complete.					DID YOUR DBS BOX CHANGE TO CHANNEL 100?
CABLE BOX BRAND	CODE	Press ENTER and “DBS
ARCHER	1, 5, 17	RECEIVER CONTROL IS ON”					YES		N O
		appears on the screen for about 5
CABLETENNA	1, 17					SET UP	ENTER SELECT WITH [		] THEN PRESS [ENTER]
		seconds, then press ENTER. The
CABLEVIEW	15, 16, 17, 21, 25					EXIT	PRESS [SET UP] TO EXIT
							SELECT
		screen in step 5 appears.
CITIZEN	15, 16, 17, 21, 25
		JVC	]	100	SONY		]	205
CURTIS	2, 8
DIAMOND	1, 17	ECHOSTAR	]	100	RCA		]	205
GC BRAND	15, 16, 17, 21, 25	If the DBS receiver’s channel does not change as shown
GEMINI	15	above;
GENERAL INSTRUMENTS	1, 4, 6, 11, 12, 15, 28	A Press w e to select “NO”, then press ENTER.
HAMLIN	10, 18, 23	B Repeat steps 8 – 9.
JASCO	15	NOTES:
JERROLD	1, 4, 6, 11, 12, 15, 28
		● The Controller may not work with all types of cable box or DBS
NOVAVISION	2, 8
		receiver.
OAK	7, 20
		● If your cable box does not respond to any code between 1 and 28,
PANASONIC	13, 14
		you cannot use the Controller to change cable box channels. In this
PULSER	15, 16, 17, 21, 25
		case, make sure to leave the cable box turned on and tuned to the
RCA	13, 14
		proper channel before the scheduled start time of timer recording.
REGAL	10, 18, 23
		Contact your cable company about the possibility of exchanging your
REMBRANDT	1, 16, 17
		current cable box with the one compatible with your unit.
SAMSUNG	5, 16, 24
		● If your DBS receiver does not respond to the code, you cannot use
SCIENTIFIC ATLANTA	2, 8	the Controller to change satellite channels. In this case, make sure to
SIGMA	7, 20	leave the DBS receiver turned on and tuned to the proper channel
SL MARX	5, 16, 17, 24, 25	before the scheduled start time of timer recording.
SPRUCER	13, 14	● The unit can only change the cable box or satellite channel through
STARGATE	5, 15, 16, 17, 21, 24, 25	the Controller during timer recording.
TELEVIEW	5, 16, 24	● If your cable box and/or DBS receiver cannot be operated with a
TOCOM	1, 4, 16	remote control (because it has no receiving window), you cannot use
UNIKA	1, 17	the Controller to change its channels. Make sure to leave the cable
UNIVERSAL	16, 17, 25	box and/or DBS receiver turned on and tuned to the proper channel
		before the scheduled start time of timer recording.
VIDEOWAY	3, 9, 22
		● If the unit’s memory backup expires because of a power failure, set
ZENITH	3, 9, 22
		the cable box and/or DBS receiver output channels and brands
DBS RECEIVER BRAND	CODE	again.
		● For customers in U.S.A.: If you are unable to set the Controller,
JVC (DISH Network)	51	contact JVC toll free at 1-800-252-5722.
ECHOSTAR (DISH Network)	51
SONY (DSS)	41
RCA (DSS)	40

Page 25

Monday, 12 July 2004 14:10