Kenwood DM-9090 instruction manual Introduction Before applying power, Safety precautions

Page 2

Introduction

2 Before applying power

DM-9090 (En)

Caution : Read this section carefully to ensure safe operation.

 

 

 

 

 

 

Units are designed for operation as follows.

 

 

U.K. and Europe

AC 230 V only

For the United Kingdom

Factory fitted moulded mains plug

1.The mains plug contains a fuse. For replacement, use only a 13- Amp ASTA-approved (BS1362) fuse.

2.The fuse cover must be refitted when replacing the fuse in the moulded plug.

3.Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appro priate safety approved extension lead or adapter, or consult your dealer.If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

IMPORTANT :

The wires in the mains lead are coloured in accordance with the following code :

Blue: Neutral

Brown : Live

Do not connect those leads to the earth terminal of a three - pin plug.

Safety precautions

Caution : Read this section carefully to ensure safe operation.

 

 

WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

The marking of products using lasers

(Except for some areas)

CLASS 1

LASER PRODUCT

The marking is located on the rear panel and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.

REQUIREMENT BY NEDERLAND GAZETTE

Batteries are supplied with this product. When they empty, you should not throw away. Instead, hand them in as small chemical waste.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents DM-9090 Units are designed for operation as follows Introduction Before applying powerSafety precautions Factory fitted moulded mains plugContents Special feature AccessoriesImportant Safeguards Power OFF Information that you should know Safety Precautions Handling of Mini DiscInstallation position Dust countermeasureReference notes Beware of condensation Maintenance CleaningMemory backup Be especially careful in the following conditionsMD system System connections Digital input / output jacks OpticalAbout the system control connections About the system control operationsNames and functions of parts Listening through headphonesStandby mode Display / Main unitDescription of main unit keys Remote control unit Model RC-M0702 Infrared ray systemOperation Operation of remote control unitLoading batteries 1Remove the cover.2Insert batteries.3Close the coverPlaying tracks in order from track No Disc recorded in monaural modePlayback of Mini Disc Before playing a MDSelect the desired title PreparationPress the Title Search key T L ERandom playback 1Enter the track modeEnter the track mode Select the desired track numberTo pause playback Skipping tracksSearching in a track To stop playbackProgramming tracks in a desired order Initiate the program modeProgramming Select track numbers in the order you want to play themTo clear tracks from the program To add a track to the programChecking the order of tracks Clearing tracks from the endTo stop repeated playback Repeated playbackTo repeat only the programmed tracks To repeat the entire discSelect before starting recording Recording-related keys AUTO/MANUAL keyMonitor key REC LEVEL? REC Mode keySelecting the setting adjustment mode Auto TIME?When Auto LEVEL? is displayed When D.REC LEVEL? is selectedWhen Auto TIME? is displayed When Fade TIME? is displayedAnalog recording 1Adjust the settings if requiredRecording Analog input Select Analog or MonoStart recording Adjust the recording level. Main unit onlySelect Auto or Manual After recording, eject the Mini DiscSelect one of Digital 1, 2 Recording Digital inputDigital recording To fade in and fade out the musicTrack being played Track Erase Adjust the digital source recording levelUnlock Synchro recording with CD playback Digital recording and ScmsReordering tracks by moving them EditingSelecting the editing function type Erasing desired tracks Quick EraseV E Moving the track being played Track MoveSelect Move Select the move destinationExecute the track reordering operation To cancel the editing results Edit CancelImage of track moving Eject the Mini Disc2Select the track numbers to be moved Moving several tracks at a time Quick Move1Select Q.MOVE End the selection of the track numbers to be moved2 / Ç? Image of track insertionP Ç? / 0 0 8 / Ç? E2Preview the result Dividing the track being played Track DivideSelect Divide V I D E +Image of track division Image of previewExecute the track divide operation 5 + 5 +2Select the track to be combined Combined tracks are decreased automaticallyImage of track combination Execute the track combine operationA S E Erasing the track being played Track EraseSelect Erase Confirm that the track has been erasedImage of track erasure 2To erase desired tracks 1To erase all MD tracksR a S E 5 ? a B CImage of track deleting Quick Erase When Disc Error is displayedS C Error Erasing desired tracksTotal number of title characters About preset titlesEditing titles Characters usable in title editingL M Input the titleL M N W O O D 3To change or erase a titleN E O O D a B C Execute title change or deletion Title editing function keysScrolling the display S C1Transmit the CD text into the MD recorder CD text editingCopying the CD text Single C D t e x tTime Display key Changing the displayed contentsThis key allows to switch the mode of time display Fade keyTimer operations Timer playback, timer recordingSymptom Cause Operation to resetSymptoms related to MD standard Case of difficultyDisplayed Message Meaning Action Other symptoms Symptom Cause RemedySpecifications Memo For your records
Top Page Image Contents