JVC 0905TNH-FN-FN manual Timer Recording, Enter the date using Cursor U / D, then press Cursor P

Timer Recording

Video	VR		VCR
DVD-RW	DVD-RW	DVD-R

You can set the unit to record up to 8 programmes, up to a month in advance. Daily or weekly programme recordings are also available.

•Be sure to set the clock before entering a timer programming.

•You can select the timer programming list by pressing [PROG] twice. In this case, continue from step 5.

Insert a recordable disc or a tape with a record tab.

1 In stop mode, press [SET UP].

2 If you select “Advanced Setting Menu,” proceed to step 3.

If you select “Easy Setting Menu,” proceed to step 4.

3 Select “Recording” using

[Cursor U / D], then press [ENTER].

4 Select “Timer Programming” using [Cursor U / D], then press [ENTER].

The Timer Programming list will appear.

5 Select a programme that is not set using [Cursor U / D], then press [ENTER].

Timer Programming VCR DVD

Date Start End CH DVDVCR Speed PDCVPS

1.- - -

2.- - -

3.- - -

4.- - -

5.- - -

6.- - -

7.- - -

8.- - -

6 Enter the date using [Cursor U / D], then press [Cursor P].

Each time you press [Cursor D] at the current date, the timer recording mode will change as follows.

e.g., 1st January

01/01

Daily

M-F (Mon.-Fri.)

W-SAT

W-FRI

W-SUN

31/01

7 Enter the time to start and to end using [Cursor U / D], then press [Cursor P].

8 Select the channel number to record using [Cursor U / D], then press [Cursor P].

To record from external input, select “AV1,” “AV2” or “AV3.”

9 Select the recording media (“DVD” or “VCR”) using [Cursor U / D], then press [Cursor P].

10 Select the recording speed using [Cursor U / D], then press [Cursor P]. (Refer to “Recording Speed” on

page 23 for DVD or page 64 for VCR.)

11 Select VPS / PDC “ON” or “OFF” using [Cursor U / D]. (See page 31.)

12 Press [ENTER] when all information required is entered.

Your programme setting is stored.

•To set another programme, repeat steps 5 to 12.

•To exit, press [SET UP] or [PROG].

•If the recording times of two or more programmes overlap, “Overlap” and overlapped programme numbers are displayed. (See pages 30 and 32.)

Timer Programming					VCR		DVD
Date Start	End	CH	DVD	Speed		VPS
			VCR			PDC
1. 01/01 12:00	13:00	P01	DVD	XP		ON

2.- - -

3.- - -

4.- - -

5.- - -

6.- - -

7.- - -

8.- - -

13 Press [TIMER ].

The icon will appear on the front panel display and the unit enters to the timer-standby mode.

Note

•If you have not set the clock, the clock setting window will appear after step 4. Continue from step 5 in “Manual Clock Setting” on page 22 before programming the timer.

•Press [Cursor L / P] to move the cursor in the timer programming menu.

•If a basic recording or one-touch timer recording is in progress on one component (e.g. VCR) and the timer recording set for the other component (e.g.

DVD) is about to begin, the unit automatically switches to the programmed channel for timer recording 2 minutes before the programmed starting time, and the recording in progress (for VCR) will be cancelled UNLESS their recording channels are the same. If their recording channels are the same, the timer recording will start without cancelling the recording currently in progress. In this case, the recording of the same channel will be made on both DVD and VCR.

Recording

EN 29