Before Operation-VCR part
Tuning in a video channel on your TV
Notes
•The output frequency of this video recorder (VCR) is set at UHF channel 60. If channel 60 is already used by another TV station, or if the picture is distorted, you can change the transmitter channel of your DVD/VCR Combi receiver. Stages 5 ~ 8 will show you how to change the output frequency of your DVD/VCR Combi receiver.
•Your TV receives signals from the video recorder (VCR) like another TV station. You have to select a channel number on your TV and tune it in so that you may watch video tapes. If you have used a SCART cable then your TV should already have a dedicated video channel built into it, usually called AV.
1.Make sure that you have correctly installed your VCR as described earlier in this book.
Press POWER to turn on your DVD/VCR Combi receiver. Turn on your TV.
2.Insert a
Don’t worry if you don’t have a
3.Tune this channel until the video picture is sharp and the sound is clear.
If you have used a SCART cable you will not have to tune your TV, simply select the AV channel. The AV channel is already
4.Store this channel on your TV.
You will need to look at the TV instruction book if you do not know how to do this.
5.Only carry out stages 5 ~ 8 if you cannot obtain clear video playback as described in stages 1 ~ 4. Select a TV channel number on which you wish to watch video’s.
Make sure that your DVD/VCR Combi receiver is in standby pressing POWER on the remote control (only the clock will be displayed).
6.Press PROG. + or - on the front of your DVD/ VCR Combi receiver for more than 4 seconds.
RF60 will appear in the display window.
The following picture will be displayed on the TV screen.
RF CHANNEL 60
P | i |
RSET |
7.Press PROG. + or - to select another video channel. You may select any channel number between 22 and 68.
You can also set it to “OFF” if there is any interfer- ence when your TV is connected to the DVD/VCR Combi receiver with a SCART lead.
8.Select a TV channel number on which you wish to
watch video’s. Press 
STANDBY/ON on the front of your DVD/VCR Combi receiver when you have finished. Tune this channel so that a bright blue screen appears. Store this channel on your TV.
Notes
Make sure that you have correctly installed your DVD/VCR Combi receiver and successfully tuned in a dedicated video channel on your TV. If you do not tune in a dedicated video channel on your TV you will be unable to view and record video tapes!
Using your VCR for the very first Initial preset
For the following steps we do assume that you have just connected your video recorder for the very first time. In this case the video recorder is on after mains connection. You should not touch any buttons yet. On the connected TV you will now see.
Note - If this menu does not appear, your video recorder was programmed already.
1.Select the country according to your area with F and G.
“A”: Austria, “B”: Belgium, “CH”: Switzerland, “D”:
Germany, “DK”: Denmark, “E”: Spain, “F”: France,
“I”: Italy, “N”: Norway, “NL”: Netherlands, “P”:
Portugal, “S”: Sweden, “SF”: Finland, OTHERS.
|
| A | B | CH | D | DK | E F I | |||
|
| N | NL | P | S | SF | OTHERS |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| OK i |
| ||
ACMS |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
2.Press OK to start the automatic storing of the channels of the TV stations in your area.
01 C02 00
|
|
|
|
|
|
|
|
|
|
| E | ||
ACMS
i
Installation and Setup
17