LG Electronics MT-42PZ40B, MZ-42PZ42V Turning on the Monitor just after installation

Page 14

Caution

When installing the monitor vertically, you have to change the menu display mode so that the menus will appear correctly and also to protect the monitor from overheating (Refer to p. 17).

Install this monitor only in a location where adequate ventilation is available.

To Mount on a Wall

To Install on a Desktop

Wall mount minimum allowable clearances for

Pedestal mount minimum allowable clearances for

adequate ventilation.

adequate ventilation.

4 inches

4 inches

4 inches

4 inches

2 inches

 

 

2 inches

 

4 inches

 

 

 

 

 

 

 

 

 

 

4 inches

4 inches

2.36 inches

Turning on the Monitor

- When using the remote control, aim it at its sensor on the Monitor.

Turning on the Monitor just after installation

1.Connect power cord correctly.

2.Press the ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby mode. Press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT button on the remote control and then the Monitor will switch on.

Turning on the Monitor (power cord is still connected)

1. If the Monitor was turned off with the ON/OFF button on the Monitor

• Press the ON/OFF button on the Monitor to turn the Monitor on.

2.If the Monitor was turned off with the remote control and the ON/OFF button on the Monitor

Press the ON/OFF button on the Monitor and then press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT button on the remote control to turn the Monitor on.

14

Image 14
Contents Plasma Monitor Wide angle range of vision What is a Plasma Display ?Easy installation Big screenContents Earth wire should be connected Safety InstructionsDo not use water the Monitor while cleaning Do not insert any object into the exhaust ventDo not pull the cord but the plug when unplugging Only use the specified batteriesBack Panel Controls of the MonitorFront Panel Controls Back Panel RCA Type Control Lock SwitchWatching External Equipments Scart TypeWatching Cable TV When the Interface board is installed External Equipment Viewing SetupsWatching VCR When the Interface board is installed How to connectPC Setup Connecting PCSetup Instructions to Connect a PC to your Monitor Resolution Horizontal Vertical Displayable Monitor SpecificationRGB1 Mode Resolution Horizontal Vertical RGB2 Mode Resolution Horizontal VerticalControl only Remote Control Key FunctionsInstalling Batteries PIP Position change the sub picture positionAccessories Optional ExtrasMonitor Installation Options Desktop Pedestal InstallationTo Mount on a Wall To Install on a Desktop Turning on the Monitor just after installationTurning on the Monitor power cord is still connected Turning on the MonitorPSM Picture Status Memory Menu Language Selection optionPicture Menu Options Manual Picture Control User optionSound Menu Options AVL Auto Volume LevelerAdjusting Sound Control User option SSM Sound Status MemoryMenu Rotation for Vertical Viewing Sleep TimerSpecial Menu Options OrbiterChild lock Adjusting Auto Colour ControlManual Colour Temperature Control User option Picture Phase Adjustments RGB1 PC mode only Auto Adjustment RGB1 PC mode onlyAdjusting Horizontal/ Vertical Position Screen Menu OptionsScreen Adjustments Video or AV1, AV2 and S-Video mode only Initializing Reset to original factory valueSelecting Wide VGA mode RGB1, RGB2 PC mode only Setting Picture Format Split ZoomPIP Picture-in-Picture Feature Watching Twin Picture Twin Picture Setup OptionsSelecting a Input Signal Source for the Twin Picture Selecting Twin Picture Sound OptionsRS-232C configurations External Control Device SetupType of connector D-Sub 9-pin male Set IDInput Select Command2b Command Reference ListPower Command2a Transmission / Receiving ProtocolVolume Mute Command2e Aspect Ratio Command2cScreen Mute Command2d Volume Control Command2fPIP Position Command2q OSD Select Command2lExternal Control Mode Command2m Treble Command2rGreen Adjustment Command2w Colour Temperature Command2uRed Adjustment Command2v Blue Adjustment Command2$IR Code NEC Format How to connectRemote Control IR Code NEC Format Code Hexa Function ARCTroubleshooting Checklist Page Page Page MT-42PZ41V/B/R/S MZ-42PZ42V/B/R/S Product SpecificationsMT-42PZ40V/B/R/S MT-42PZ43V/B/R/S MZ-42PZ43V/B/R/S