LG Electronics MT-42PZ41R, MZ-42PZ42V Colour Temperature Command2u, Red Adjustment Command2v

Page 28

20. Colour Temperature (Command2:u)

GTo adjust colour temperature.

You can also adjust CSM in the special menu. Transmission

[k][u][

][Set ID][

][Data][Cr]

 

 

 

 

 

Data

0: Normal

1: Cool 2: Warm 3: User

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

21. Red Adjustment (Command2:v)

GTo adjust red in colour temperature.

Transmission

[k][v][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

* Refer to ‘Real data mapping 2’. See page 28.

Acknowledgement

[v][ ][Set ID][ ][OK][Data][x]

22. Green Adjustment (Command2:w)

GTo adjust green in colour temperature.

Transmission

[k][w][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

* Refer to ‘Real data mapping 2’. See page 28. Acknowledgement

[w][ ][Set ID][ ][OK][Data][x]

23. Blue Adjustment (Command2:$)

GTo adjust blue in colour temperature.

Transmission

[k][$][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

* Refer to ‘Real data mapping 2’. See page 28.

Acknowledgement

[$][ ][Set ID][ ][OK][Data][x]

25. Abnormal State (Command2:z)

GTo recognize an abnormal state.

Transmission

[k][z][ ][Set ID][ ][FF][Cr]

Data 0: Normal (Power on and signal)

1:No signal (Power on)

2:Turn the monitor off by remote control

3:Turn the monitor off by sleep time function

4:Turn the monitor off by RS-232C function

5:5V down

6:AC down

7:Fan Alam

Acknowledgement

[z][ ][Set ID][ ][OK][Data][x]

* This function is “read only”.

26. Orbiter (Command2:p)

GTo control the orbiter function on/off. You can also adjust orbiter in special menu.

Transmission

[j][p][ ][Set ID][ ][Data][Cr]

Data 0 : Orbiter off

1: Orbiter on

Acknowledgement

[p][ ][Set ID][ ][OK][Data][x]

27. White Wash (Command2:q)

GTo control the white wash function on/off. You can also adjust White Wash in special menu.

Transmission

[j][q][ ][Set ID][ ][Data][Cr]

Data 0 : White Wash off 1 : White Wash on

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

24. PIP Input Select (Command2:y)

GTo select input source for sub picture in PIP/Twin pic- ture mode. You can also adjust input source for sub picture using PIP INPUT button on remote control.

Transmission

[k][y][ ][Set ID][ ][Data][Cr]

Data 0: RGB1

1:COMPONENT (or AV1)

2:VIDEO (or AV2)

3:S-VIDEO

Acknowledgement

[y][ ][Set ID][ ][OK][Data][x]

*Real data mapping 1 0 : Step 0

A : Step 10 (Set ID 10)

F: Step 15 (Set ID 15)

10 : Step 16 (Set ID 16)

64 : Step 100

*Real data mapping 2

0 : -10

5 : -9

A : -8

2D: -1

32:0

37:+1

5F: +9

64: +10

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Plasma Monitor What is a Plasma Display ? Easy installationWide angle range of vision Big screenContents Safety Instructions Do not use water the Monitor while cleaningEarth wire should be connected Do not insert any object into the exhaust ventDo not pull the cord but the plug when unplugging Only use the specified batteriesFront Panel Controls Controls of the MonitorBack Panel Control Lock Switch Watching External EquipmentsBack Panel RCA Type Scart TypeExternal Equipment Viewing Setups Watching VCR When the Interface board is installedWatching Cable TV When the Interface board is installed How to connectSetup Instructions to Connect a PC to your Monitor Connecting PCPC Setup Displayable Monitor Specification RGB1 Mode Resolution Horizontal VerticalResolution Horizontal Vertical RGB2 Mode Resolution Horizontal VerticalRemote Control Key Functions Installing BatteriesControl only PIP Position change the sub picture positionAccessories Optional ExtrasMonitor Installation Options Desktop Pedestal InstallationTurning on the Monitor just after installation Turning on the Monitor power cord is still connectedTo Mount on a Wall To Install on a Desktop Turning on the MonitorMenu Language Selection option Picture Menu OptionsPSM Picture Status Memory Manual Picture Control User optionAVL Auto Volume Leveler Adjusting Sound Control User optionSound Menu Options SSM Sound Status MemorySleep Timer Special Menu OptionsMenu Rotation for Vertical Viewing OrbiterManual Colour Temperature Control User option Adjusting Auto Colour ControlChild lock Auto Adjustment RGB1 PC mode only Adjusting Horizontal/ Vertical PositionPicture Phase Adjustments RGB1 PC mode only Screen Menu OptionsSelecting Wide VGA mode RGB1, RGB2 PC mode only Initializing Reset to original factory valueScreen Adjustments Video or AV1, AV2 and S-Video mode only Setting Picture Format Split ZoomPIP Picture-in-Picture Feature Twin Picture Setup Options Selecting a Input Signal Source for the Twin PictureWatching Twin Picture Selecting Twin Picture Sound OptionsExternal Control Device Setup Type of connector D-Sub 9-pin maleRS-232C configurations Set IDCommand Reference List Power Command2aInput Select Command2b Transmission / Receiving ProtocolAspect Ratio Command2c Screen Mute Command2dVolume Mute Command2e Volume Control Command2fOSD Select Command2l External Control Mode Command2mPIP Position Command2q Treble Command2rColour Temperature Command2u Red Adjustment Command2vGreen Adjustment Command2w Blue Adjustment Command2$Remote Control IR Code NEC Format How to connectIR Code NEC Format Code Hexa Function ARCTroubleshooting Checklist Page Page Page Product Specifications MT-42PZ40V/B/R/S MT-42PZ43V/B/R/SMT-42PZ41V/B/R/S MZ-42PZ42V/B/R/S MZ-42PZ43V/B/R/S
Top Page Image Contents