LG Electronics MT-42PZ42B, MZ-42PZ42V Do not pull the cord but the plug when unplugging

Page 5

*Safety instructions have two kinds of information, and each meaning of it is as below.

WARNING The violation of this instruction may cause serious injuries and even death.

The violation of this instruction may cause light injuries or damage of the NOTES product.

Take care of danger that may happen under specific condition.

NOTES

Never touch the power plug with a wet hand.

- This may cause an electric shock.

Disconnect from the mains and remove all connec- tions before moving.

Do not place the Monitor in a built-in installation such as a bookcase or rack.

- Ventilation required.

Do not plug when the power cord or the plug is dam- aged or the connecting part of the power outlet is loose.

- This may cause a fire or an electric shock.

Dispose of used batteries carefully to protect a child from eating them.

- In case that it eats them, take it to see a doctor immediately.

When moving the Monitor assembled with speakers do not carry holding the speakers.

-This may cause the Monitor to fall, causing serious injury to a child or adult, and serious damage to the Monitor.

Unplug this product from the wall outlet before clean- ing. Do not use liquid cleaners or aerosol cleaners.

-This may cause damaged the Monitor or could give an electric shock.

When installing the Monitor on a table, be careful not to place the edge of its stand.

-This may cause the Monitor to fall, causing serious injury to a child or adult, and serious damage to the Monitor.

Do not place an outside antenna in the vicinity of over- head power lines or other electric light or power cir- cuits.

- This may cause an electric shock.

There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls.

- This may cause an electric shock.

Do not pull the cord but the plug when unplugging.

- This may cause a fire.

Ensure the power cord doesn’t trail across any hot objects like a heater.

- This may cause a fire or an electric shock.

Contact the service center once a year to clean the internal part of the Monitor.

- Accumulated dust can cause mechanical failure.

The distance between eyes and the screen should be about 5 ~ 7 times as long as diagonal length of the screen.

- If not, eyes will strain.

Unplug the Monitor from the wall outlet when it is left unattended and unused for long periods of time.

-Accumulated dust may cause a fire or an electric shock from deterioration or electric leakage.

Only use the specified batteries.

-This make cause damaged the Monitor or could give an electric shock.

5

Image 5
Contents Plasma Monitor Easy installation What is a Plasma Display ?Wide angle range of vision Big screenContents Do not use water the Monitor while cleaning Safety InstructionsEarth wire should be connected Do not insert any object into the exhaust ventOnly use the specified batteries Do not pull the cord but the plug when unpluggingBack Panel Controls of the MonitorFront Panel Controls Watching External Equipments Control Lock SwitchBack Panel RCA Type Scart TypeWatching VCR When the Interface board is installed External Equipment Viewing SetupsWatching Cable TV When the Interface board is installed How to connectPC Setup Connecting PCSetup Instructions to Connect a PC to your Monitor RGB1 Mode Resolution Horizontal Vertical Displayable Monitor SpecificationResolution Horizontal Vertical RGB2 Mode Resolution Horizontal VerticalInstalling Batteries Remote Control Key FunctionsControl only PIP Position change the sub picture positionOptional Extras AccessoriesDesktop Pedestal Installation Monitor Installation OptionsTurning on the Monitor power cord is still connected Turning on the Monitor just after installationTo Mount on a Wall To Install on a Desktop Turning on the MonitorPicture Menu Options Menu Language Selection optionPSM Picture Status Memory Manual Picture Control User optionAdjusting Sound Control User option AVL Auto Volume LevelerSound Menu Options SSM Sound Status MemorySpecial Menu Options Sleep TimerMenu Rotation for Vertical Viewing OrbiterChild lock Adjusting Auto Colour ControlManual Colour Temperature Control User option Adjusting Horizontal/ Vertical Position Auto Adjustment RGB1 PC mode onlyPicture Phase Adjustments RGB1 PC mode only Screen Menu OptionsScreen Adjustments Video or AV1, AV2 and S-Video mode only Initializing Reset to original factory valueSelecting Wide VGA mode RGB1, RGB2 PC mode only Split Zoom Setting Picture FormatPIP Picture-in-Picture Feature Selecting a Input Signal Source for the Twin Picture Twin Picture Setup OptionsWatching Twin Picture Selecting Twin Picture Sound OptionsType of connector D-Sub 9-pin male External Control Device SetupRS-232C configurations Set IDPower Command2a Command Reference ListInput Select Command2b Transmission / Receiving ProtocolScreen Mute Command2d Aspect Ratio Command2cVolume Mute Command2e Volume Control Command2fExternal Control Mode Command2m OSD Select Command2lPIP Position Command2q Treble Command2rRed Adjustment Command2v Colour Temperature Command2uGreen Adjustment Command2w Blue Adjustment Command2$IR Code NEC Format How to connectRemote Control IR Code NEC Format ARC Code Hexa FunctionTroubleshooting Checklist Page Page Page MT-42PZ40V/B/R/S MT-42PZ43V/B/R/S Product SpecificationsMT-42PZ41V/B/R/S MZ-42PZ42V/B/R/S MZ-42PZ43V/B/R/S