LG Electronics MT-42PZ43B OSD Select Command2l, External Control Mode Command2m, Treble Command2r

Page 27

12. OSD Select (Command2:l)

GTo select OSD (On Screen Display) on/off when con- trolling remotely.

Transmission

[k][l][ ][Set ID][ ][Data][Cr]

Data 0 : OSD off

1 : OSD on

Acknowledgement

[l][ ][Set ID][ ][OK][Data][x]

13. External Control Mode (Command2:m)

GTo lock the front panel controls on the monitor and remote control. When setting this mode, only control the monitor with RS-232C.

Transmission

[k][m][ ][Set ID][ ][Data][Cr]

Data 0 : Lock off

1 : Lock on

Acknowledgement

[m][ ][Set ID][ ][OK][Data][x]

*If you’re not using the remote control, use this mode. When main power is on/off, external control lock is released.

16. PIP Position (Command2:q)

GTo select sub picture position for PIP.

You can also adjust the sub picture position using PIP POSITION button on the remote control or in the screen menu.

Transmission

[k][q][ ][Set ID][ ][Data][Cr]

Data 0 : Right down on screen

1: Left down on screen

2: Left up on screen

3: Right up on screen

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

17. Treble (Command2:r)

GTo adjust treble.

You can also adjust treble in the sound menu.

Transmission

[k][r][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

* Refer to ‘Real data mapping1’. See page 28. Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

14. PIP / Twin (DW) (Command2:n)

GTo control the PIP (Picture In picture)/Twin picture.

You can also control the PIP/TWIN picture using the PIP or Twin picture button on the remote control or in the screen menu.

Transmission

[k][n][ ][Set ID][ ][Data][Cr]

Data

0: PIP/DW off

3: DW2

 

1: PIP (S)

4: PIP (L)

 

2: DW1

 

 

Acknowledgement

 

 

 

 

 

 

[n][

][Set ID][ ][OK][Data][x]

 

 

 

 

 

 

15. PIP Sound Select (Command2:p)

GTo select main or sub sound for PIP/Twin picture.

You can also adjust main or sub sound for PIP/Twin pic- ture using PIP SOUND button on the remote control or in the screen menu.

Transmission

[k][p][ ][Set ID][ ][Data][Cr]

Data 0: Main image sound 1: Sub image sound

Acknowledgement

[p][ ][Set ID][ ][OK][Data][x]

18. Bass (Command2:s)

GTo adjust bass.

You can also adjust bass in the sound menu.

Transmission

[k][s][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

* Refer to ‘Real data mapping1’. See page 28.

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

19. Balance (Command2:t)

GTo adjust balance.

You can also adjust balance in the sound menu.

Transmission

[k][t][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

* Refer to ‘Real data mapping1’. See page 28. Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

27

Image 27
Contents Plasma Monitor Big screen What is a Plasma Display ?Easy installation Wide angle range of visionContents Do not insert any object into the exhaust vent Safety InstructionsDo not use water the Monitor while cleaning Earth wire should be connectedOnly use the specified batteries Do not pull the cord but the plug when unpluggingControls of the Monitor Front Panel ControlsBack Panel Scart Type Control Lock SwitchWatching External Equipments Back Panel RCA TypeHow to connect External Equipment Viewing SetupsWatching VCR When the Interface board is installed Watching Cable TV When the Interface board is installedConnecting PC Setup Instructions to Connect a PC to your MonitorPC Setup RGB2 Mode Resolution Horizontal Vertical Displayable Monitor SpecificationRGB1 Mode Resolution Horizontal Vertical Resolution Horizontal VerticalPIP Position change the sub picture position Remote Control Key FunctionsInstalling Batteries Control onlyOptional Extras AccessoriesDesktop Pedestal Installation Monitor Installation OptionsTurning on the Monitor Turning on the Monitor just after installationTurning on the Monitor power cord is still connected To Mount on a Wall To Install on a DesktopManual Picture Control User option Menu Language Selection optionPicture Menu Options PSM Picture Status MemorySSM Sound Status Memory AVL Auto Volume LevelerAdjusting Sound Control User option Sound Menu OptionsOrbiter Sleep TimerSpecial Menu Options Menu Rotation for Vertical ViewingAdjusting Auto Colour Control Manual Colour Temperature Control User optionChild lock Screen Menu Options Auto Adjustment RGB1 PC mode onlyAdjusting Horizontal/ Vertical Position Picture Phase Adjustments RGB1 PC mode onlyInitializing Reset to original factory value Selecting Wide VGA mode RGB1, RGB2 PC mode onlyScreen Adjustments Video or AV1, AV2 and S-Video mode only Split Zoom Setting Picture FormatPIP Picture-in-Picture Feature Selecting Twin Picture Sound Options Twin Picture Setup OptionsSelecting a Input Signal Source for the Twin Picture Watching Twin PictureSet ID External Control Device SetupType of connector D-Sub 9-pin male RS-232C configurationsTransmission / Receiving Protocol Command Reference ListPower Command2a Input Select Command2bVolume Control Command2f Aspect Ratio Command2cScreen Mute Command2d Volume Mute Command2eTreble Command2r OSD Select Command2lExternal Control Mode Command2m PIP Position Command2qBlue Adjustment Command2$ Colour Temperature Command2uRed Adjustment Command2v Green Adjustment Command2wHow to connect Remote Control IR Code NEC FormatIR Code NEC Format ARC Code Hexa FunctionTroubleshooting Checklist Page Page Page MZ-42PZ43V/B/R/S Product SpecificationsMT-42PZ40V/B/R/S MT-42PZ43V/B/R/S MT-42PZ41V/B/R/S MZ-42PZ42V/B/R/S