LG Electronics MT-42PZ41R, MZ Connecting PC, Setup Instructions to Connect a PC to your Monitor

Page 9

Connecting PC

-To enjoy vivid picture and sound, connect a PC to the Monitor.

-Avoid keeping a fixed image on the monitor’s screen for a long period of time. The fixed image may become permanent- ly imprinted on the screen; use a screen saver when possible.

-Connect PC to the RGB1 INPUT(PC INPUT) or RGB2 INPUT(DIGITAL RGB INPUT) port of the Monitor; change the res- olution output of PC accordingly.

-There might be a noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Then change the PC mode into other resolution or change the refresh rate into other rate or adjust the brightness and contrast on the menu until the picture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the manufacturer of the PC graphic card.

-The synchronization input form for Horizontal and Vertical frequencies is separate.

Setup Instructions to Connect a PC to your Monitor

-We recommend using 640x480, 60Hz for the PC mode, they provide the best picture quality.

-If the resolution of PC is over UXGA, there will be no picture on the Monitor.

-Connect the signal cable from the monitor output port of the PC to the RGB1 INPUT(PC INPUT) port of the Monitor or the signal cable from the DVI output port of the PC to the RGB2 INPUT(DIGITAL RGB INPUT) port on the Monitor.

-Connect the audio cable from the PC to the Audio input on the Monitor. (Audio cables are not included with the Monitor).

-If using a sound card, adjust PC sound as required.

-This monitor apply a VESA Plug and Play Solution. The monitor provides EDID data to the PC system with a DDC pro- tocol. The PC adjusts automatically to use this monitor.

-DDC protocol is preset for RGB1 (Analog RGB), RGB2 (DVI, Digital RGB) mode.

-If required, adjust the monitor settings for Plug and Play functionally.

-If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB1 INPUT (PC INPUT) or RGB2 INPUT (DIGITAL RGB INPUT) to display the PC on the monitor.

If graphic card on the PC does output analog and digital RGB simultaneously, set the monitor to either RGB1 or RGB2; (the other mode is set to Plug and Play automatically by the monitor.)

-DOS mode may not work depending on video card if using a DVI-I cable.

-To see a normal picture, match the VGA mode and DVI signal (640x480, 852x480, 848x480). (See page 19)

PC Setup

1.Turn on the PC and apply power to the Monitor.

2.Turn on the display by pressing the POWER button on the Monitor’s remote control.

3.Use the INPUT SELECT button on the remote control to select the RGB1 or RGB2 input source.

4.Set the resolution output of the PC to SXGA or under (1280 x 1024, 60Hz).

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Plasma Monitor Easy installation What is a Plasma Display ?Wide angle range of vision Big screenContents Do not use water the Monitor while cleaning Safety InstructionsEarth wire should be connected Do not insert any object into the exhaust ventOnly use the specified batteries Do not pull the cord but the plug when unpluggingControls of the Monitor Front Panel ControlsBack Panel Watching External Equipments Control Lock SwitchBack Panel RCA Type Scart TypeWatching VCR When the Interface board is installed External Equipment Viewing SetupsWatching Cable TV When the Interface board is installed How to connectConnecting PC Setup Instructions to Connect a PC to your MonitorPC Setup RGB1 Mode Resolution Horizontal Vertical Displayable Monitor SpecificationResolution Horizontal Vertical RGB2 Mode Resolution Horizontal VerticalInstalling Batteries Remote Control Key FunctionsControl only PIP Position change the sub picture positionOptional Extras AccessoriesDesktop Pedestal Installation Monitor Installation OptionsTurning on the Monitor power cord is still connected Turning on the Monitor just after installationTo Mount on a Wall To Install on a Desktop Turning on the MonitorPicture Menu Options Menu Language Selection optionPSM Picture Status Memory Manual Picture Control User optionAdjusting Sound Control User option AVL Auto Volume LevelerSound Menu Options SSM Sound Status MemorySpecial Menu Options Sleep TimerMenu Rotation for Vertical Viewing OrbiterAdjusting Auto Colour Control Manual Colour Temperature Control User optionChild lock Adjusting Horizontal/ Vertical Position Auto Adjustment RGB1 PC mode onlyPicture Phase Adjustments RGB1 PC mode only Screen Menu OptionsInitializing Reset to original factory value Selecting Wide VGA mode RGB1, RGB2 PC mode onlyScreen Adjustments Video or AV1, AV2 and S-Video mode only Split Zoom Setting Picture FormatPIP Picture-in-Picture Feature Selecting a Input Signal Source for the Twin Picture Twin Picture Setup OptionsWatching Twin Picture Selecting Twin Picture Sound OptionsType of connector D-Sub 9-pin male External Control Device SetupRS-232C configurations Set IDPower Command2a Command Reference ListInput Select Command2b Transmission / Receiving ProtocolScreen Mute Command2d Aspect Ratio Command2cVolume Mute Command2e Volume Control Command2fExternal Control Mode Command2m OSD Select Command2lPIP Position Command2q Treble Command2rRed Adjustment Command2v Colour Temperature Command2uGreen Adjustment Command2w Blue Adjustment Command2$How to connect Remote Control IR Code NEC FormatIR Code NEC Format ARC Code Hexa FunctionTroubleshooting Checklist Page Page Page MT-42PZ40V/B/R/S MT-42PZ43V/B/R/S Product SpecificationsMT-42PZ41V/B/R/S MZ-42PZ42V/B/R/S MZ-42PZ43V/B/R/S
Top Page Image Contents