LG Electronics 37LC2RR, 42LC2RR When connecting Hdmi cable, Turn on the DVD player, insert a DVD

Page 22

CONNECTIONS & SETUP

When connecting with an S-Video cable

1. How to connect

Connect the S-VIDEO output of the DVD to the

1	S -VIDEO input on the set.

2	Connect the audio outputs of the DVD to the AUDIO
	input jacks on the set.

2. How to use

	CONNECTIONS&	■ Turn on the DVD player, insert a DVD.
	CONNECTIONS&	■ Select AV1 input source with using the INPUT button on
		■ Select AV1 input source with using the INPUT button on
		the remote control.
		■ Refer to the DVD player's manual for operating instructions.
	SETUP	When connecting HDMI cable
		When connecting HDMI cable

1.How to connect

1 Connect the HDMI output of the DVD to the HDMI IN 1(DVI) or HDMI 2 jack on the set.

2No separated audio connection is necessary.

2.How to use

■Select HDMI1/DVI or HDMI2 input source with using the INPUT button on the remote control.

■Refer to the DVD player's manual for operating instructions.

VIDEO	S-VIDEO							L		R	ANT IN

ANT OUT

12

	RGB IN
	RGB	AUDIO
	PC/DTV)	(RGB/DVI)
		AV OUT
	S-232C IN
	ROL&SERVICE)
	IN 1		(MONO)
	AV	S-VIDEO VIDEO	(MONO)
	AV		AUDIO
			AUDIO

RGB IN

			RGB
		HDMI IN	(PC/DTV)
		HDMI IN
	REMOTE	2
	CONTROL		RS-232C IN
	IN		RS-232C IN
	IN	1 (DVI)	(CONTROL&SERVICE)
			(CONTROL&SERVICE)

1

!NOTE

G If the DVD supports Auto HDMI function, the DVD output resolution will be automatically set to 1280x720p.

G If the DVD does not support Auto HDMI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the DVD to 1280x720p.

HDMI-DVD OUTPUT

20

Image 22

Contents LCD TV Page Wet Location Marking Important Safety InstructionsEarth wire should be connected Do not insert any object into the exhaust ventNever touch the power plug with a wet hand Do not use water the product while cleaningDo not pull the cord but the plug when unplugging Unplug this product from the wall outlet Aerosol cleanersClean the internal part of the product Onal length of the screenContents Initializing Reset to Original Factory Settings On Screen Menus Selection and AdjustmentAuto Configure Rgbpc Mode Only ContentsAccessories IntroductionHome Menu DVRRemote Control Sensor Power Standby Indicator ControlsConnection Options Brightness Adjusts brightness on screen Or off, depending on modeReturns to the TV mode Mode sourceInstalling Batteries Remote control effective rangeHow to remove the Cable Management Wire ArrangementBundle the cables using the supplied twister holder Ensure adequate ventilation by follow Desktop Pedestal InstallationInstallation Ing the clearance recommendationsConnections & Setup Connections & SetupHow to connect VCR SetupWhen connecting with an antenna How to useSetup When connecting with a RCA cableWhen connecting with an S-Video cable Connections External Equipment Connections External StereoAV OUT Setup When connecting with a component cable DVD SetupRefer to the DVD players manual for operating instructions Remote control When connecting Hdmi cableTurn on the DVD player, insert a DVD Turn on the digital set-top box Hdstb SET-TOP BOX Setup480i Connect the RGB output of the digital set-top box to When connecting with a Hdmi cableRGB PC/DTV jack on the set When connecting with a Hdmi to DVI cable Hdmi in 1DVI jack on the setWhen connecting with a D-sub 15 pin cable PC SetupAudio When connecting Hdmi to DVI cable 1. How to connect Connect the PC audio Output720x400 Supported Display Resolution RGBPC/HDMI PC mode640x480 800x600Channel Selection Volume AdjustmentTurning the TV on Basic OperationBasic Operation ON-SCREEN Menus Language SelectionTime Control Special FunctionsProgressing the Time Control Function ‘Progress Bar’?Progressing the Time control function, play Using the remote controlButton to speed up Recording Instant RecordAfter adjusting the recording time, select ENTER. Status bar will be displayedWatching & Record Recorded TV Recorded Program Selection and Popup MenuSpecial Playing Recorded ProgramsFunctions Using the Remote Control After setting the Manual Rec., press the Enter button Manual RecordingScheduled List Video QualityWhen completing, this message is displayed If you selects Yes, this message is displayedTV Program Selection for PIP Selecting an Input Signal Source for PIP/Double WindowWatching PIP/Double Window/POP AV1 AV2Adjusting PIP Transparency PIP mode only Sub Picture Size Adjustment PIP mode onlyMoving the Sub Picture PIP mode only Swapping the PIP/Double WindowOn Screen Menus Selection and Adjustment Cable TV Channels Or E button to selectTV Menu / Setup Manual Program ADDING/DELETING ChannelsManual program Fine Tuning AdjustmentTV Menu FineBooster First favorite channel position Favorite Channels SetupFavorite Channel Use the F or G button to set the desired channelPicture Adjustment TV Menu Auto Color Temperature Control ACC Manual Color Temperature Control ACC User Option Appropriate adjustmentsPicture ADVANCED-CINEMA Mode Setup Press the F or G button to select Low or High ADVANCED-BLACK LevelBlack Level Low Screen gets darkerReset TV Menu Sound Adjustment To the musicManual Sound Control Dasp User Option Auto Volume Leveler AVL Balance Adjustment MenuTV Speakers Setup STEREO/SAP Broadcasts Setup Clock Setup Set the Date and TimeON/OFF Timer Setup Select Auto Off To select the Timer menuAuto OFF Select O n or OffUtes selected Sleep TimerButton once To select the Special menu KEY LockSelect Key lock Using Closed Captions Closed CaptionsXD Demo TvmenuTV Menu Screen Adjustment Clock Manual ConfigurePhase Position / V-positionSelect the desired XGA resolution Selecting Wide XGA ModeSelect XGA mode To select the Screen menuAspect Ratio Control ARC You can move the Horizon screen using D or ButtonRGB-PC and Hdmi PC input source use 43 or 169 aspect ratio Initializing TV Menu / ScreenType of Connector D-Sub 9-Pin Male External Control Device SetupRS-232C Setup GNDCommunication Parameters RS-232C ConfigurationsSet ID RXD TXD GND DTR DSR RTS CTSCommand Reference List Transmission / Receiving ProtocolAppendix Acknowledgement k Set ID OKDatax Transmission k$ Set ID DataCr External Input 1st frame Remote Control IR CodesIR Codes Repeat frameCode Function Programming a code into a remote mode Programming the Remote ControlProgramming Codes VCRs Troubleshooting Checklist Remote control Doesn’t work Power is suddenly Turned offAudio function does not work Cleaning the Screen MaintenanceProduct Specifications Cleaning the Cabinet