Table 4
|
|
|
| ����� |
|
| |
����������� | ����� ������� | ���������� ����������� | ����� |
| ������ | ������������ | ����� ����� |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
�������� |
|
|
|
|
|
| � |
|
|
|
|
|
|
|
|
������ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
��������� | � | � |
|
|
|
| � |
|
|
|
|
|
|
|
|
����� | � | � |
|
|
|
| � |
|
|
|
|
|
|
|
|
����������������� |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
���������������� |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
�������� |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
��������� |
|
| � |
| � | � | � |
|
|
|
|
|
|
|
|
SETUP
The setup menu contains less frequently used adjustments that may be required during installation (e.g. On Screen Display language selection or the display of Test Patterns).
POWER ON
If selected (AUTO), this option allows the system to be switched on directly from the mains power supply once the initialisation phase is terminated.
If disabled (STAND BY), at the end of the initialisation phase the system assumes Standby status and awaits the
TEST PATTERNS
Displays a series of five test patterns, which are useful when install- ing the system and checking basic functions. Use the ▲ and ▼ keys to browse through the test patterns
INITIAL SETTINGS
Restores original factory settings except for Position, Orientation, Y/C Delay, Zoom and Focus.
�������
MENU
LANGUAGE
Lists the languages available for the On Screen Display menus.
INPUTS LIST
In order to make the HTL40 LINK system increasingly flexible, the functions described below make it possible to modify the inputs selection menu and adapt it so that it matches the requirements of the user more closely.
The main page displays all the inputs physically present on the DigiOptic™ Image Processor.
If one or more of the inputs is not used, they can be hidden in the list, which is called by pressing the 0 key.
For this purpose select SOURCES LIST and position the cursor on the line corresponding to the input you wish to hide. Now press the
◀key and select activation or deactivation of the relative source (Fig.24).
The deactivation or activation of the source results in automatic renumbering of the remaining active inputs.
����������������������������
����������� | ��������� |
|
��������� � | ��������� |
|
����������� � | ����������� |
|
����������� � | ������������������ ��� | �� |
| ���� |
|
�������������������� � | ���������� |
|
�������������������� ��� | ���������� |
|
������������������� � | ���������� |
|
������������������� � | ���������� |
|
��������������� � | ����������� |
|
��� ������������ �� | ������������ |
|
��� ����� �� | �������� |
|
��� ���� �� | ������� |
|
Fig.24
Active video signal sources (shown in the inputs selection menu) are distinguished by tick symbols.
You can also identify the input with a more significant name for the user (e.g. with the name of the connected device).
The current source can be renamed in the
For this purpose, after selecting the display of a given input, select the option Name. This function is designed to facilitate the identi- fication of a source connected to a particular input.
To assign a name to a source you can use up to twelve alphanumeric characters (for more details refer to the following section).
25