Kathrein 9986492, MSK 33 UFOmicro DiSEqC menu, General information, Display fields, RX 0 E2 10

Page 33

Sat Operation

UFOmicro DiSEqC menu

General information

In the UFOmicro mode, one or various head stations EXU 544 in a Kathrein in- house system can be tested. The test can be carried with or without a KATHREIN satellite receiver from the 400 series or higher.

The following functions and features are available:

1.Simulates the basic function of a Kathrein satellite receiver.

Transmitting of „virgin call for address“, „call for address“, „program command“, „poweron/off“ – in consideration of the allocated pages of the collision protec- tion.

2.Simulation of max. 12 UFD receivers in conjunction with the installed UFOµ- head stations. 12 pre-programmed factory settings can be called up.

3.Monitoring (watching and recording) of DiSEqC commands, which are transmitted between the UFOmicro head stations and the UFD receivers for a specific period of time.

4.Display of the respective receiver 01...12 with the head end reply, receiver ad- dress, remote IF and the collision protections pages (t0, t1, t2 in ms). Analogue picture assessment of the remote IF, which is allocated from the head station or in conjunction with the spectrum representation in the spectrum menu.

5.Antenna socket testing ( testing the disconnection function).

Display fields

RX field

 

In this field, the telegrams, which are received from the current

FRAME ADD COM

-DATA-

head station, are displayed.

RX 0 E2 10 33

-----

In the case of activated monitoring, a maximum of five tele-

 

 

 

 

grams are recorded. The respective displayed telegram is

indicated with the no. RX: 0 ...... RX:4. Flashing signalises the beginning of the re-

cording. At the end of the recording, the last recorded telegram is displayed.

Status field

In the centre of the screen, the status of the head station and the registered re- ceiver as well as the transmission error and the transmission status are displayed.

The following messages are possible:

!no acknowledge EXU544!

Transmission error EXU ...... MSK33

 

 

! acknowledge EXU544 !

No transmission error

 

 

!Rec. -- not registered!

Receiver is not yet registered in the head station

 

 

Rec. -- - registered -!

Receiver registered in the head station

 

 

!Rec. -- -- Stand-by --!

Receiver is registered but in standby

 

 

UFOu + Bus-Control

MSK 33 considers the collision protection, INT33

is equipped

 

 

 

UFOu without Bus-Control

MSK 33 does not consider the collision protec-

tion, INT33 is not equipped

 

 

 

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Sat/TV/FM Test Receiver MSK Page Preface Contents Checking the LNB supply voltage of a satellite receiver Selecting the colour standards PAL, Secam and Ntsc Mpeg transport stream interface TS-Parallel, Lvds optional Measuring an audio signal via the AV socket Scart Measurement of analogue signals in Sat operation 100 113 107Explanation of symbols General safety informationImportant Notes Validity of this manualConnections Safety InstructionsProper use Mechanical loadbearing capacityFunctions FunctionsFunction Functions overviewReturn path LP DVB-S DVB-S/C/TFront panel Displays, Operating Elements and ConnectionsRear panel Mains connection Mains switch DC socket Option / XLR-socketHeadphone connection TS parallel Option 10 AUXSide view MSK Observing angle of the on screen displayOperating Concept ScreenFrequently recurring softkeys Menu selection General information for operationMain menu Accu CAP % I=0.00 aMains voltage / mains switch Place of installation of the MSKOn/Off switch Safety fuseAccumulator and Battery Operation Accumulator operationDC socket option Connections Measurement Possibilities Level measurementMaximal input level Sat menu Sat OperationSetting of the LNB voltage supply Selecting the LO frequencyEntering the transponder frequency Bargraph Level range Comment Display Switch-over of Analog digit. DvbsIII Calling up menu LNB-CONTROLLNB control menu KHz control signalLNB supply voltage LNB current drawChecking the LNB supply voltage of a satellite receiver Calling up the DiSEqC/V SEC menuDiSEqC DiSEqC menu TX display field Submenu for entering DiSEqC commandsDisplay field a Display field BExample Entering and transmitting a DiSEqC command Simple DiSEqCData burst Tone burst General information UFOmicro DiSEqC menuDisplay fields RX 0 E2 101390 Tx+rx CommandOperating the menus ModusSat Operation Sending a V-SEC command TX SEC menuEntering the hex numbers Initial ANALOG-menu Level-dependent acoustic signalCalling up the sound subcarrier MenuVideo polarity Second Anlaog menuSetting of the de-emphasis Audio carrier settingSat subcarrier menu Audio carrier frequencyAudio carrier table for reception type Audio carrier tables for the satellite receptionDigital Measurements SAT Digital menu27.500 Level measurement Digital Min./Max. levels TV menu TV OperationC10 210.25MHz A65.0dBµV Rf chanTV control menu TV-DiSEqC /VSEC menuLNB U= 0.0 V I= 0 mA Selecting the standard Analogue menuAudio carrier table for TV reception Selecting the audio carriersMeasuring the current level Measuring the min./max. levelSelecting the colour standards PAL, Secam and Ntsc Measuring audio carrier spacingSelecting demodulation for DVB-C measurement TV Digital menuMode 900 SR1DVB-T optional Selecting channel bandwidthsChBW 8MHz Return path if menu Return Path if MenuAudio carrier table for if reception Analog menuMeasurement of the min./max. level Measurement of the audio carrier spacingMeasurement of the current level QAM64 mode Entering symbol rateIf RP Digital Menu Radio Operation Radio menuRadio Analog menu Measuring the min/max level FM Measure ALLDecoder operation AV MenuDecoder operation baseband Video input Video outputBreaking voltage RGB operationMpeg transport stream interface TS-Parallel, Lvds optional Mpeg Decoder Menu Optional PAT 083sat KiKa Phoenix Setting Menu Unit dBmVOffset 0.0 dB Screen Menu Screen setupSetting the time Click button Setting the dateSystem Menu Calls up the SYS TEM menuSaving the unit settings Saving and calling up unit settingsCalling up saved settings Copy MenuPrinting out all measurements in Sat mode Printing out all measurements in TV modeSpectr Mode MenuEnlarging the videotext Text MenuHolding the videotext Original videotext sizeHorizontal zoom -Enlarging the video signal Horizontal zoom Reducing the video signalScope Menu Video scope menuMeasurement of the amplitude of the video signal Measurement of video signals via the AV socket ScartSelecting the video line Audio Scope TimePos DiSEqC Scope Position and triggering of the DiSEqC signalSaving function Shot ContMarker Span Large ¡ mark ßlevel Spectral MenuAna MaxMarker Dig Marker AnaMeasurement of digital signals in Sat operation Cross-polarisation measurement on signals in SAT operationZoom marker Max off Measurement of the bit error rate BER Constellation diagram for Qpsk DVB-SConst Menu Colour representation of I/Q value pairsMeasurement of signal noise ratio SNR Carrier offsetFrontend locked Inverting /not inverting a constellation diagram Selecting the symbol rate symbol-clock27.500 SR Selecting the code rateExamples for Qpsk constellation diagrams Measurement of modulation error rate MER Constellation diagram for QAM DVB-CZoom Inverting /not inverting constellation diagramExamples for QAM constellation diagram Const Menu Measurement of bit error rate BER Constellation diagram DVB-T optionalMeasurement of signal noise ration SNR Carrier modeHierarchy Code rate Guard Invers Frontend locked Channel display Impulse response representation Echo representation optional Measuring principle Broadband Cable Analysis Measuring System MSKTrack MVG10 Downstream measurement Upstream measurementMSK33 MVG10 RGB MSK33Cable system With return path capable amplifiers Display of the check point Auto MeasureInterfaces Modem / RS 232 interfaceConnection cable for modem / RS Setting local echo Setting baud rateSetting hardware handshake Modem/RS232 menuTTY mode Code PasswordAnsi mode Log-in procedureRequesting help Example for logging-in in Ansi modeInterfaces List of the command abbreviations STU Loading and saving predefined settingsSTU RET LDUMaintenance, Storage and Customer Service Printer paper-exchanging the ribbon Before opening the unit, disconnect the supply voltageRibbon exchange Command overview framing byte Overview of DiSEqC commandsCommand overview address byte Technical AppendixReset Reset DiSEqC minicontroller Command overview command byteCommand overview data byte DiSEqC commands for Kathrein matricesCommand for Kathrein matrix 9xx-series Command for Kathrein matrix EXRChannel and frequency table standard B/G frequency in MHz Channel tablesVHF-CCIR UHF-CCIR USB/OSB ESBVHF UHF Channel and frequency table standard Lfrequency in MHzVII Channel and frequency table standard D/K frequency in MHzViii XIIChannel and frequency table standard I frequency in MHz Channel and frequency table standard M/N frequency in MHz Channel and frequency table standard M/Nfrequency in MHz Technical Data Technical dataPower supply SNR Qpsk BERMER Accessories Scope of deliveryAssignment of the Scart socket TXD RXD RTS CTS DSR GND DCD DTR Assignment of RS232 socketAssignment of socket TS Parallel optional Unit variants General notes Downloading New MSK33 Operating Software114 115
Top Page Image Contents