Kathrein 9986492, MSK 33 manual Digital Measurements, SAT Digital menu, 27.500

Page 41

Digital Measurements

SAT DIGITAL menu

BACK

7/8

CR >

			level
			beep
---SAT MEASURE ALL----
---SAT MEASURE ALL----			mea-
min/max: 38.0/65.0 dBµV			sure

	70		MPEG


><1832.50MHz D65.0 dBµV			PICTURE

Calls up the previous menu.

Level-dependent acoustic signal

In the function, “level beep,“ an acoustic signal is generated, whose pitch is proportional to the received signal level. With this

signal, it is possible to optimally align the receiving antenna to a transmitter.

In this menu, the receiving frequency can be changed using the cursor buttons, ◄►.

Convulsion code for Sat measurement

7/8 CR ➧

With this button, the convulsion code is set for demodulating the QPSK signals from 1/2 to 8/9. The setting is adopted for the constellation analysis.

Symbol rate entry

27.500

SR ➧

You can choose between four preset symbol rates for correct level measurement of digital signals ( in SAT mode: 22,000; 27.500; 20,000 and 27,500). It also possible to change the preset symbol rates by numerical entry. In the SAT area, symbol rates can be programmed from 0.5 ...32 Ms. This programming is adopted at the constellation analysis. With the [MHz] button, the entry is completed.

The correct symbol rate must be set for proper level measurement of signals!

MPEG decoder menu (OPTION)

MPEG

In this function, the PAL list (programme association table) and the respective PIDs (packet identifier) of the transport stream are displayed. The desired programmes can be selected in this menu and represented on the screen (refer to „MPEG de- coder“).

41

Image 41

Contents Sat/TV/FM Test Receiver MSK Page Preface Contents Checking the LNB supply voltage of a satellite receiver Selecting the colour standards PAL, Secam and Ntsc Mpeg transport stream interface TS-Parallel, Lvds optional Measuring an audio signal via the AV socket Scart Measurement of analogue signals in Sat operation 100 113 107Explanation of symbols General safety informationImportant Notes Validity of this manualConnections Safety InstructionsProper use Mechanical loadbearing capacityFunctions FunctionsFunction Functions overviewReturn path LP DVB-S DVB-S/C/TFront panel Displays, Operating Elements and ConnectionsRear panel Mains connection Mains switch DC socket Option / XLR-socketHeadphone connection TS parallel Option 10 AUXSide view MSK Observing angle of the on screen displayFrequently recurring softkeys Operating ConceptScreen Menu selection General information for operationMain menu Accu CAP % I=0.00 aMains voltage / mains switch Place of installation of the MSKOn/Off switch Safety fuseDC socket option Accumulator and Battery OperationAccumulator operation Connections Maximal input level Measurement PossibilitiesLevel measurement Sat menu Sat OperationEntering the transponder frequency Setting of the LNB voltage supplySelecting the LO frequency Bargraph Level range Comment Display Switch-over of Analog digit. DvbsIII Calling up menu LNB-CONTROLLNB control menu KHz control signalLNB supply voltage LNB current drawDiSEqC Checking the LNB supply voltage of a satellite receiverCalling up the DiSEqC/V SEC menu DiSEqC menu TX display field Submenu for entering DiSEqC commandsDisplay field a Display field BData burst Tone burst Example Entering and transmitting a DiSEqC commandSimple DiSEqC General information UFOmicro DiSEqC menuDisplay fields RX 0 E2 101390 Tx+rx CommandOperating the menus ModusSat Operation Entering the hex numbers Sending a V-SEC command TXSEC menu Initial ANALOG-menu Level-dependent acoustic signalCalling up the sound subcarrier MenuVideo polarity Second Anlaog menuSetting of the de-emphasis Audio carrier settingSat subcarrier menu Audio carrier frequencyAudio carrier table for reception type Audio carrier tables for the satellite reception27.500 Digital MeasurementsSAT Digital menu Level measurement Digital Min./Max. levels TV menu TV OperationC10 210.25MHz A65.0dBµV Rf chanLNB U= 0.0 V I= 0 mA TV control menuTV-DiSEqC /VSEC menu Selecting the standard Analogue menuAudio carrier table for TV reception Selecting the audio carriersMeasuring the current level Measuring the min./max. levelSelecting the colour standards PAL, Secam and Ntsc Measuring audio carrier spacingSelecting demodulation for DVB-C measurement TV Digital menuMode 900 SR1ChBW 8MHz DVB-T optionalSelecting channel bandwidths Return path if menu Return Path if MenuAudio carrier table for if reception Analog menuMeasurement of the current level Measurement of the min./max. levelMeasurement of the audio carrier spacing If RP Digital Menu QAM64 modeEntering symbol rate Radio Analog menu Radio OperationRadio menu Measuring the min/max level FM Measure ALLDecoder operation AV MenuDecoder operation baseband Video input Video outputMpeg transport stream interface TS-Parallel, Lvds optional Breaking voltageRGB operation 3sat KiKa Phoenix Mpeg Decoder Menu OptionalPAT 08 Offset 0.0 dB Setting MenuUnit dBmV Screen Menu Screen setupSetting the time Click button Setting the dateSystem Menu Calls up the SYS TEM menuSaving the unit settings Saving and calling up unit settingsCalling up saved settings Copy MenuPrinting out all measurements in Sat mode Printing out all measurements in TV modeSpectr Mode MenuEnlarging the videotext Text MenuHolding the videotext Original videotext sizeHorizontal zoom -Enlarging the video signal Horizontal zoom Reducing the video signalScope Menu Video scope menuSelecting the video line Measurement of the amplitude of the video signalMeasurement of video signals via the AV socket Scart Pos Audio ScopeTime DiSEqC Scope Position and triggering of the DiSEqC signalSaving function Shot ContMarker Span Large ¡ mark ßlevel Spectral MenuAna MaxMarker Dig Marker AnaZoom marker Max off Measurement of digital signals in Sat operationCross-polarisation measurement on signals in SAT operation Measurement of the bit error rate BER Constellation diagram for Qpsk DVB-SConst Menu Colour representation of I/Q value pairsFrontend locked Measurement of signal noise ratio SNRCarrier offset Inverting /not inverting a constellation diagram Selecting the symbol rate symbol-clock27.500 SR Selecting the code rateExamples for Qpsk constellation diagrams Measurement of modulation error rate MER Constellation diagram for QAM DVB-CZoom Inverting /not inverting constellation diagramExamples for QAM constellation diagram Const Menu Measurement of bit error rate BER Constellation diagram DVB-T optionalMeasurement of signal noise ration SNR Carrier modeHierarchy Code rate Guard Invers Frontend locked Channel display Impulse response representation Echo representation optional Measuring principle Broadband Cable Analysis Measuring System MSKTrack MVG10 Downstream measurement Upstream measurementMSK33 MVG10 RGB MSK33Cable system With return path capable amplifiers Display of the check point Auto MeasureConnection cable for modem / RS InterfacesModem / RS 232 interface Setting local echo Setting baud rateSetting hardware handshake Modem/RS232 menuTTY mode Code PasswordAnsi mode Log-in procedureRequesting help Example for logging-in in Ansi modeInterfaces List of the command abbreviations STU Loading and saving predefined settingsSTU RET LDUMaintenance, Storage and Customer Service Ribbon exchange Printer paper-exchanging the ribbonBefore opening the unit, disconnect the supply voltage Command overview framing byte Overview of DiSEqC commandsCommand overview address byte Technical AppendixReset Reset DiSEqC minicontroller Command overview command byteCommand overview data byte DiSEqC commands for Kathrein matricesCommand for Kathrein matrix 9xx-series Command for Kathrein matrix EXRChannel and frequency table standard B/G frequency in MHz Channel tablesVHF-CCIR UHF-CCIR USB/OSB ESBVHF UHF Channel and frequency table standard Lfrequency in MHzVII Channel and frequency table standard D/K frequency in MHzViii XIIChannel and frequency table standard I frequency in MHz Channel and frequency table standard M/N frequency in MHz Channel and frequency table standard M/Nfrequency in MHz Power supply Technical DataTechnical data MER SNRQpsk BER Assignment of the Scart socket AccessoriesScope of delivery TXD RXD RTS CTS DSR GND DCD DTR Assignment of RS232 socketAssignment of socket TS Parallel optional Unit variants General notes Downloading New MSK33 Operating Software114 115