Wegener Communications 4600 manual Alarm and Carrier LEDs Both On, Alarm or Warning LED On

Page 56

UNITY 4600 USERS MANUAL

Missing an Audio, Video, or ASI Output With Other Outputs Okay

intermediate line amplifiers) has DC power and trace the connection from the LNB to the IRD or try replacing the LNB. If a spectrum analyzer is available, look for the carrier at the L-band intermediate frequency. (For domestic C- band satellites, this is 5150 minus the downlink frequency in MHz.)

b.The selected IRD RF port has failed. To rule out this possibility, try connecting the RF cable to another RF port and select that port (or use the RF Switch Bypass to force that other port).

c.The IRD receiver card has failed. To rule this out, try using another IRD.

2.If the first alarm message is “No Carrier Lock”, verify the RF Feed Port, Carrier Frequency, Data Rate, FEC Ratio, and ID Tag (if Tags are in use) settings. Also verify that the LNB LO frequency setting (in the IRD) is correct for the selected RF feed port.

3.If the alarm message is “RF Signal Overload”, then reduce the carrier power entering the U4600. Either add in-line attenuation (a splitter will do) or remove line amplification in the RF circuit between the LNB and the IRD.

Alarm and Carrier LEDs Both On

The U4600 may not be authorized for the network’s Conditional Access. If the AUTH LED is Off and the alarm message, "Unauthorized for CA” appears, contact your net- work provider to gain authorization in its Conditional Access database.

Alarm or Warning LED On

Check the front-panel display for alarm or warning messages. Table 4.1: Alarm and Warning Descriptions on page 49 describes U4600 alarm and warning messages. If the message definitions are too technical to help debug the problem, report the mes- sages to your network provider.

Alarm and Warning LEDs Off

If no alarms or warnings are shown, suspect a bad connection or mis-programming of the U4600:

1.If audio or video are missing, check the front-panel monitor jacks. If the front mon- itor connections are OK, check the signal connections from the rear of the unit to the destination. If an audio is missing from the rear-panel outputs and cannot be detected at the front-panel monitors, check that a valid audio stream is selected for that port and that the network provider has supplied non-quiet programming on that audio.

2.If the ASI output is missing, check the signal connections from the rear of the unit to the destination. If okay, check with the network provider to verify what Program Mapping (Release 2 or later) may be in effect.

800032-01 Rev. F

48

www.wegener.com

Image 56
Contents UNITY4600 800032-01 Rev. F Iii This page intentionally blank Table of Contents List of Figures List of Tables 800032-01 Rev. F Viii Manual Overview Unity 4600 User’s ManualProduct Overview Unity 4600 Professional Media RecorderCharacteristic Specification Unity 4600 Product SpecificationsTechnical Specifications Audio Output Dtmf OutputFront Panel Monitors Serial PortsAlarm/Cuing Relays Ethernet PortsFront Panel E-Mails ChassisCharacteristic Transport-In OptionsTurbo PSK Receiver Option, Broadcom Protocols DVB-QPSK Receiver with 4-Port RF Switch OptionSwitched RF Inputs Turbo Receiver with 4-Port Switch Option RF Switch Input DVB-QPSKSafety Summary Glossary of Terms and AbbreviationsGlossary of Terms Term DefinitionRecovery Or RecoveryBoot loader AutomatedPresets Table Network ProtectionMode PES StreamService Descriptor Service SettingsSetting, Last CommandedYour warranty Unpacking and InspectionLocation and Mounting Mandated Suppression Radio Frequency EmissionsDesktop Installation Mechanical LoadingU4600 Connections See .2 for Transport Options for this slotRear Panel Connectors Connector Type Pin Signal Name Designation Alarm CuingComposite Video Out Serial ControlConnector Type Pin Signal Name Designation Ethernet DVB-QPSK with 4-way RF Switch Transport In OptionTurbo-PSK with 4-way RF Switch Transport In Option 115/230 VACSerial Port Configuration Device Handling Terminal I/O Modem I/OAux Data Printer OuputInstallation Testing VOLnnnnnnnnnnnnn Relay Pulse CheckThis page intentionally left blank Functional Summary Automated Recovery Theory of OperationUnity 4600 Functional Block Diagram Monitoring and ControlOperation from Front Panel LCD Screen RelationshipsLCD Screen Content LCD Screen RelationshipSummary of Top-Level LCD Screens and Their Functions Home Default Screens Screen Name Functions/Applications Unit SetupDownload Screen as Default Audio FP Monitor Selection Screen as DefaultInterpreting Front Panel LEDs Front-Panel LED Indicator DescriptionsIndicator Label Color and State Meaning Rear-Panel Front Panel Audio MonitorCommands Operation from Local/Remote TerminalOverview and Syntax UserAud1rt Same as aud1rt above Audmon port# Dels entryGhostlist action PID Dtmfvol percentForcerf port LAN Gateway addr LAN IP addrLAN Mode mode Mode DHCP, WEG, or Static LatchalarmsLAN Subnet addr Lnbpwr outputASI Loadnv sourceOr O Partpid pidPassword One to six alphanumeric characters Permch valueState ON, OFF, or WRpath from domain Rpath Relay addrRpath to username@addr Port RouteSET from source Setlabel labelSettimeout source time SourceSetpedest Setpin valueCommand displays internal unit temperature if available Unmute sourcesourcesource Alarm LED On and Carrier LED Off MaintenanceGeneral Troubleshooting Alarm and Warning LEDs Off Alarm and Carrier LEDs Both OnAlarm or Warning LED On Alarms and Warnings Alarm and Warning DescriptionsContent for ASI N/A Content RoutingProblem High Error RateInvalid VBI Data Fmt Invalid Video FormatIP Address Conflict KMS Stream LostNo RF Signal No Dhcp Server FoundNo Genlock Sync No ID Tag FoundRF Signal Overload Setting Out of RangeTest Mode in Use PMT DisappearedVideo Buff Overflow Video CMD MutedVideo Not Found Video PES Data LostWarranty Technical SupportThis page intentionally left blank Info Screens Menu ScreensMisc Setups Parameter ScreensIndex LED Questions Rack This page intentionally left blank
Related manuals
Manual 75 pages 30.76 Kb

4600 specifications

Wegener Communications 4600 is a state-of-the-art digital satellite receiver designed for high-performance applications in the broadcasting and telecommunications sectors. This advanced receiver is part of Wegener's renowned line of products, catering to a range of broadcasting needs, from television to data communications. The Wegener 4600 offers a host of features that make it an attractive choice for both broadcasters and service providers.

One of the key features of the Wegener 4600 is its robust satellite reception capability. It supports a wide range of satellite frequencies and protocols, ensuring reliable connectivity in various scenarios. The device is engineered to work seamlessly with the DVB-S and DVB-S2 standards, which allow for efficient compression and transmission of high-definition video content. This ensures that users can deliver high-quality broadcasts with minimal latency, an essential factor in today's fast-paced media landscape.

Another standout characteristic of the Wegener 4600 is its versatile encoding and decoding capabilities. It supports a variety of video and audio codecs, including MPEG-2, MPEG-4, and AAC, among others. This flexibility enables content providers to choose the best formats for their specific needs, enhancing the viewer's experience while optimizing bandwidth usage.

The Wegener 4600 also features advanced management and monitoring capabilities. Through its user-friendly interface, operators can easily configure settings, monitor performance metrics, and manage multiple streams. This functionality is crucial for maintaining optimal performance and ensuring the reliability of the broadcast.

In terms of connectivity, the device supports various interfaces, including ASI and IP, enabling integration with existing broadcast infrastructures. This adaptability is a significant advantage for organizations looking to upgrade or expand their capabilities without extensive redesigns of their current systems.

Security is another key aspect of the Wegener 4600. It incorporates robust encryption options that protect content from unauthorized access and piracy. This feature is increasingly important as the demand for secure transmission of sensitive data grows.

Overall, Wegener Communications 4600 stands out in the crowded market of digital satellite receivers. With its combination of superior reception capabilities, versatile encoding options, advanced management features, and strong security protocols, it represents an ideal solution for broadcasters and telecommunications providers seeking to enhance their service offerings and deliver high-quality content to viewers worldwide.