Hunter Fan owner manual Activating a Station with the ICR Remote System

Page 14

2.After the Receiver starts to beep, release the button.

3.Press either the “ON” or “OFF” button on your transmit- ter.

4.The Receiver will beep 4 additional times indicating that it has learned the new Transmitter address and will respond only to it from this point on.

The ICR system will allow you to remotely turn on and off any station on your Hunter controller with the press of a button. Once on, the station will run for the run time you have designated in the ICR transmitter.

Activating a Station with the ICR Remote System.......................

To remotely activate a station or program:

1.Plug your Receiver into an active SmartPort® wiring harness (one attached to a powered controller) and wait for 2 beeps indicating the Receiver is ready.

2.If your Transmitter is not on (no display), press any button for at least 1 second and release. The Transmitter will display the active station.

3.Use the or buttons to display the station or program (A,B, or C) you would

like to start.

4. Momentarily press the “ON”

 

button to start the station or

 

program. The Transmitter will

45"5*0/

display the word “TRANSMIT”

 

and will flash for about 4 seconds indicating that it is sending the command to the Receiver. If you are near the Receiver, you will hear it beep 2 times, indicating that it has received the command.

5.Press the “OFF” button at any time to turn off the station or program. The display will again read “TRANSMIT” and flash, and the Receiver will again beep twice. The ICR

is designed to turn one station on at a time. Therefore, turning a station on while another is already on will cause the first station to turn off.

6.If one of the programs (A,B, C or P1 through P18) is selected, all stations in the selected program will run sequentially for the run time programmed in the controller.

10

Image 14
Contents For Use with Hunter Controllers Installation Instructions ICRPage Table of contents TABLa de contenido Introduction ICR Components SmartPort Carrying Case TransmitterReceiver SmartPort Wiring Harness Installing the SmartPort Wiring HarnessPro-C Controller SmartPort Installation Wiring the SmartPort to hunter controllersSRC Controller SmartPort Installation Blue Red WhiteTypical Installations Preparing the Transmitter for UseTo change the Run Time Installing the Transmitter BatteriesChanging the Run Time To change the Transmitter address Changing the Transmitter AddressChanging the Maximum Number of Stations To change the Maximum Number of StationsACC/ACC Decoder Controllers Preparing the Receiver for UseSRC/Pro-C/ICC Controllers Changing the Receiver AddressActivating a Station with the ICR Remote System To remotely activate a station or programMaximizing Operating Range Troubleshooting Guide CAUSes SolutionsDefault Settings Operating SpecificationsElectrical Specifications DimensionsPage Presentación del Producto Componentes del ICR SmartPort Caja EmisorReceptor Conexión de Cableado del Programador SmartPort Instalación del Arnés de Cableado SmartPortAzul Rojo Blanco Instalación SmartPort del Programador Pro-CInstalaciones Típicas Preparación del Emisor Antes de su UsoCambio del Tiempo DEL Ciclo de Riego Cambios al Tiempos de RiegoColocación de la Pila del Emisor Para Modificar la Dirección del Emisor Modificación de la Dirección del EmisorModificación del Número Máximo de Estaciones Para Modificar el Número Máximo de EstacionesPreparación del Receptor Antes de su Uso Programadores SRC/Pro-C/ICCModificación de la Dirección del Receptor Optimización de la Zona de Funcionamiento Guía Para Solucionar Problemas Problema Causas SolucionesEspecificaciones Eléctricas DimensionesEspecificaciones de Operación Reglaje por fallaFCC Compliance Notice