Magnavox MC192DMG, MC132DMG Checking or Clearing Timer Recordings, During the power failure

Page 35

With the TV/VCR on, press the MENU button.

Press the PLAY/▲ button or the STOP/▼ but- ton to select VCR PROGRAM, then press the F.FWD/B button.

MC132DMG/MC192DMG 3/22/02 1:21 PM Page 35

Checking or Clearing Timer Recordings

1

2

3 Press the PLAY/▲ button or the STOP/▼ but- ton to select PROGRAM REVIEW, then press the F.FWD/B button. The timer recording infor- mation for the program in the lowest numbered posi- tion will appear on the screen. If no timer recordings are programmed, nothing will happen when you select PROGRAM REVIEW and press the F.FWD/B button.

4 Press the F.FWD/B button to display informa- tion about the next timer recording. (If you do not press a button within 10 seconds, information about the next timer recording will appear automatical- ly.) This will continue until all positions have been dis- played. Then, the menu will disappear. You can exit the Program Review at any time by pressing the STA- TUS/EXIT button.

5 To cancel the timer recording displayed, press the CLEAR button. Either the display will disap- pear or information about other timer recordings will appear. If you do not press any other buttons, the display will disappear after all timer recordings have been displayed.

6 Repeat steps 1-4 to make sure you cleared the correct recording.

Timer Recording (cont’d) 35

2-4

POWERSLEEP/WAKE UP

1		PLAY
	REW		F.FWD		5
		STOP
	MENU	STATUS/EXIT		CLEAR
	1	2	3
	4	5	6	CH.
	4	5	6
	7	8	9
		0	ALT.CH	VOL.
		0		VOL.
	SPEED	MEMORY	PAUSE/STILL
	REC/OTR	TRACKING		MUTE

Helpful Hint

•With ShowGuard, you don’t have to worry about losing your timer recordings. If the power fails, timer recordings will be restored when the clock is reset. (The clock will reset itself automatical- ly if you are using AUTO CLOCK. Details are on pages 14-17. If you are not using AUTO CLOCK, reset the clock manually. Details are on pages 12-13.) The timer recording will not occur only if it was scheduled to take place

during the power failure.

Image 35

Contents MC132DMG/MC192DMG Model No Serial No Dear Magnavox product ownerFor Customer Use Declaration of Conformity FeaturesSafety Precautions IntroductionTable of Contents TV/VCR Maintenance Putting Batteries in the Remote ControlBattery Safety Using the Remote ControlRod Antenna Hook up your TV/VCR using one of the connections shownHooking Up the TV/VCR RF coaxial cable Not suppliedCrooked Pin Straight Pin Hooking Up the TV/VCR cont’dAudio and video cables are not supplied Select another channel Press the Power button. The TV/VCR willYou cannot set up channels if you are using a Cable Box Turning On the TV/VCRPress the STATUS/EXIT but Ton Language SelectionPress the Menu button Press the Menu buttonLine Input mode Automatic Channel SetupWait for the TV/VCR to set up channels Repeat steps 3-4 to add or delete other channels Adding/Deleting ChannelsSteps Press the CHannel o/p buttons orChannels are set. Details are on Setting the ClockManual Clock Setting Cable Box users must set the clock manuallyButtons for the year. For example, for July Setting the Clock cont’dPM, press 09, 30 FWD/B button Ton to select PRIM. SETUP. Then, pressAutomatic PBS Channel Selection Press the PLAY/ button or the STOP/ but- 1,4Wait for the TV/VCR to find the time NOW Searching flashes on the TV/VCR screenManual PBS Channel Selection Use the Number buttons to select your PBS station Daylight-Savings Time Clock is OFF Time ZoneFront Panel To the TV/VCR ANTenna Jack AC Power CordRear Panel Details are on page sixRemote Control Buttons ALT. CH Alternate Channel Button Clear ButtonSTATUS/EXIT Button STOP/ ButtonMenus on page 25 will disap Refer to the chart onWhen you finish, press the STATUS/EXIT but- ton Press the PLAY/ button or the STOP/ butDecreased brightness Adjusting the Picture Controls cont’dDecrease Increase More brilliantIf you select Status OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only OFF If you select Status ON, then select Counter only onReminder Follow the steps below to play a tape PlayingRecording options are on pages Read and follow the steps below to record a TV programTo stop recording, press the STOP/ button Tape Speeds HrsTon on the TV/VCR to stop One-Touch RecordingTape is in the TV/VCR. The record tab must be intact TV/VCR will turn off at the end of the OTRRerecording Tape Duplication TV/VCR is now in Line Input modeDetails are on Timer RecordingDaily Automatically Follow the instructions in to setRecording’s stop time. AM or PM will be set If Program not Completed appears, start again at step Timer Recording cont’dYou cannot use the Speed button at this time During the power failure Checking or Clearing Timer RecordingsTUS/EXIT button Defeat RecordingFollow the steps below to prevent accidental recording TV programming will appear while the tape is rewinding Play modeRepeat Play Insert a tape in the TV/VCR B Repeat PlayInsert a tape in the TV/VCR Press the Menu button Will become a flashing B PowerCounter will appear on the screen Setting will be lostSuper High Speed Searching LP/SLP Still modePlayback Options Forward and Reverse Searching SP/LP/SLPSmartlock menu will appear Use the Number buttons to enter your access codeSmartLock BLOCKED... message appears Ratings will remain blocked even after a power failureSmartLock cont’d Example Specific Sub-ratingsActive code again Use the Number buttons to enter your old access codeUse the Number buttons to enter your desired Same code in the Confirm Code spaceRating Explanations FWD/B button repeatedly so that OFF or on Blue BackgroundPress the PLAY/o button or the STOP/p button To select Blue BACKGROUND. Then, pressSleep timer during a recording Sleep TimerWake Up Timer Volume Bar Menu Screen Closed CaptionExample Sample Picture Half-screen text Sample Picture Standard Closed CaptionsAutomatic Operation Features Glossary Helpful Hints Helpful Hints cont’d Specifications Renewed Index MC132DMG/MC192DMG 3/22/02 121 PM Supplied Accessories