Axis Communications AXIS 241SA user manual Socks, QoS Settings, Smtp email

Page 52

52AXIS 241QA/AXIS 241SA - System options

SOCKS

SOCKS is a networking proxy protocol. The AXIS 241QA/AXIS 241SA can be configured to use a SOCKS server to reach networks on the other side of a firewall/proxy server. This function is useful if the video server is located on a local network behind a firewall, but notifications, uploads, and alarms need to be sent to a destination outside the local network (such as the Internet).

QoS

Quality of Service (QoS) provides the means to guarantee a certain level of a specified resource to selected traffic on a network. Quality can be defined as a maintained level of bandwidth, low latency, and no packet losses. The main benefits of a QoS-aware network can be summarized as:

the ability to prioritize traffic and thus allow critical flows to be served before flows with lesser priority.

greater reliability in the network, thanks to the control of the amount of band- width an application may use, and thus control over bandwidth races between applications.

The QoS in Axis network video products marks the data packets for various types of network traffic originating from the product. This makes it possible for network routers and switches to reserve a fixed amount of bandwidth for these types of traffic. The following types of traffic are marked:

live video

live audio

event/alarm traffic

management network traffic.

QoS Settings

For each type of network traffic supported by your Axis network video product, enter a DSCP (Differentiated Services Code Point) value. This value is used to mark the traffic’s IP header. When the marked traffic reaches a network router or switch, the DSCP value in the IP header tells the router or switch which type of treatment to apply to this type of traffic, for example, how much bandwidth to reserve for it.

Note that DSCP values can be entered in decimal or hex form, but saved values are always shown in decimal.

More information on Quality of Service at the Axis support web at www.axis.com/techsup

SMTP (email)

Enter the host names or addresses for your primary and secondary mail servers in the fields provided, to enable event and error email messages from the video server to predefined addresses, via SMTP.

Image 52
Contents User’s Manual About This Document Table of contents Axis video server Product description Overview of the Axis video serverLED indicators Front panel Axis 241QANetwork StatusPower Switches & connectorsRear panel Axis 241QA/AXIS 241SA Product description Using the video server Accessing the video serverSetting the root password Please see the online help for more informationLive View AMC Audio controls Video and audio streams Video stream typesMotion Jpeg MPEG-4MPEG-4 protocols and communication methods How to stream MPEG-4Axis Media Control AMC Other methods of accessing the video stream RTP+RTSPRTP/RTSP RTP/RTSP/HTTP or RTP/RTSP/HTTPSOther MPEG-4 clients Accessing the audio streamsAxis Vapix API Configuring the video server Accessing the Setup toolsImage settings Video & image settingsImage appearance Video source settings AdvancedQuad stream settings Overlay/Mask settingsMjpeg Overlay/Mask typeUpload and use an overlay image Overlay image requirementsOverlay image limitations Image Formats Image SizeUse a Privacy Mask Audio Settings Enable AudioAudio Audio ChannelsAudio Input Noise canceller threshold value Noise canceller attenuation Advanced Audio SettingsAudio Output Axis 241QA/AXIS 241SA Audio Live View Config LayoutCustomizing the default Upload Own Web FilesDefault Live View Video Default Video FormatDefault Viewer Viewer SettingsUser-defined Links Html ExamplesCheck Show Custom Link Sequence Mode External VideoInstalling PTZ devices Pan Tilt ZoomPTZ configuration Preset positionsPTZ controls PTZ control modes Using CGI links to control PTZ devicesControl panel Guard tour Preset positionsAdvanced PTZ control queue Axis 241QA/AXIS 241SA Pan Tilt Zoom Event configuration Event serversHow to set up a triggered event Event typesTriggered Event Click Add triggered on the Event typesHow to set up a scheduled event Pre-trigger and post-trigger buffersScheduled event Click Add scheduled on the Event typesSettings Camera tamperingHow to configure Motion Detection Motion detectionPort status Object SizeSystem options SecurityUsers IP Address FilterStream, IP address filtering must be enabled HttpsAxis 241QA/AXIS 241SA System options Radius Date & timeCA servers IP Address Configuration Network Basic TCP/IP settingsServices Network Advanced TCP/IP settings DNS configurationNTP Configuration Host Name ConfigurationFTP HttpRtsp QoS Settings SocksQoS Smtp emailSnmp RTP / MPEG-4Ports & devices MaintenanceSupport Configuration Resetting to the factory default settings Using the Control ButtonD-Sub connector Unit connectorsPin I/O terminal connector Pin Function DescriptionSchematic diagram I/O terminal connector COM ports RS-232 and RS-485Axis 241QA/AXIS 241SA Unit connectors Checking the firmware TroubleshootingUpgrading the firmware Emergency recovery procedure Alarms, etc, to a destination outside the local network Be accessed from a web browserLit Video Image Problems No images displayed in the Web interfaceSnapshot images Only I framesAudio volume too low/high Audio Advanced SettingsAudio Axis 241QA only Poor audio qualityTechnical specifications ModelsConnectors Video access from WebApplications not General performance considerations Optimizing your systemFrame rates Motion Jpeg Frame rates MPEG-4Bandwidth Active Speaker a speaker with a built-in power amplifier GlossaryCompression See Image Compression De-interlacing See interlacingEncoder See Video encoder Fixed iris See AutoirisHalf-duplex See Full-duplex Megapixel See Pixel Axis 241QA/AXIS 241SA Glossary SSL/TSL Identity of the server Video camera See Network camera and Cctv video cameraAn I-VOP is a complete image frame Index ActionHttp API Http API requests Http port number Http serverRTP 14 Rtsp 14 Video streams 13, 15