Avaya S8500 manual Index 101

Page 6

Contents

Appendix A: Media server access	87
Accessing the command line interface of the server with SSH	87
Connecting to the media server directly	89
Connecting to the media server remotely over the network	91
Connecting to the media server remotely over a modem	91
Accessing the Maintenance Web Interface	92
Using the SAT command line prompt	93
Logins for Avaya technicians and BusinessPartners	93
Configuring the network for Windows 2000 and XP	94
Setting the browser options for Internet Explorer 6.0	95

Appendix B: Installation troubleshooting		97
Troubleshooting the installation of the media server hardware		97
Troubleshooting the configuration of the media server hardware		98
Troubleshooting the installation of the license file and		100
the Avaya authentication file
Index	. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	101

6 Installing and Configuring the Avaya S8500 Media Server

February 2007

Image 6

Contents Installing and Configuring the Avaya S8500 Media Server ReleaseAvaya Inc All Rights Reserved Introduction Media server configuration Install an S8500 Media Server as an LSP Index 101 Introduction AudienceHow to use Avaya installation documents Pre-installation requirements Preinstallation tasks to complete at the customer siteVerifying that all the required equipment is on site Ensuring that the preinstallation tasks are complete S8500 hardwareS8500C front panel S8500B front panel Equipment specifications UPSS8500 Media Server specifications Feature S8500B S8500C CD-ROM/DVD-ROM IDEAcoustical About the Server Availability Management Processor About Samp functionalityAbout Samp connections Samp connections for S8500B About Samp software Samp connections for S8500CAbout media server port connections S8500 port connectionsS8500C Media Server connectivity guide About modem connections Modem connectivity on the S8500 Media ServerAbout media gateways About Processor EthernetModem options About Processor Ethernet About S8500 LSP mode S8500 LSP license file About SSHTN8412AP Sipi Snmp Configuration Configuring the Snmp modules in the UPSDefault IP addresses for the UPS Prerequisites for configuring the Snmp moduleAdministering the Snmp module Security AlertSetting selected traps alarming Default IP addresses for the Ethernet switch Preparing to configure the Ethernet switchConfiguring the Ethernet switch Page Page Communication Manager installation Clearing the ARP cache on the laptopApplying power to the media server Accessing the media serverConfiguring Telnet for Windows 2000 and Windows XP Installing Avaya Communication Manager Communication Manager installation Media server configuration Under Security, select Administrator Accounts Opening the Maintenance Web InterfaceCreating a super-user login Type susers in the login group fieldAbout the Avaya Installation Wizard Type sampcmd samp-update status and press Enter Running the Avaya Installation WizardInstalling Samp firmware Verifying the RMB IP informationConfiguring the modem Click Execute PingSelect Change Modem Setting and click Continue Enabling firewall settingsSelect Configure individual services and click Continue Enabling network time serversEnabling network time servers Configuring the NIC Checking LED activity on the dual NICConfiguring the NIC Disconnecting from the media server Click ContinueIP interface translations Inputting initial system translationsAdding media gateways Cabinet Cabinet DescriptionSet the Ipsi Control of Port Networks field to enabled Enabling the IpsiSaving translations Setting the alarm activation levelAdding the Ipsi to the system Type add ipserver-interface PNnumber and press EnterIP interface configuration Connecting to the IPSIsIpsi address configuration Programming the Ipsi for static addressingConnecting the laptop directly to the Ipsi Type show control interface and press Enter Setting the Vlan and diffserv parameters Ipsi LED display for static address Programming the Ipsi for Dhcp addressing CLKIP interface configuration Verifying connectivity to the media server CLKEnabling control of the IPSIs Verifying that the IPSIs are translatedUpgrading the Ipsi firmware version if necessary Verifying the license statusInstall an S8500 Media Server as an LSP Configuring the media server as an LSPSelect the Configure Individual Services Select Set IdentitiesSelect This is a local survivable processor LSP Administering the primary controller Enabling license server capability on a media gatewayInstalling and verifying the license on the new LSP Type stop -caf Type start -cafResetting the S8500 LSP Click Advanced SettingOpening the TCP ports on the S8500 LSP Readministering media gateways to point to the LSP Verifying that the primary controller identifies the new LSPPostinstallation administration Verifying translationsList station List trunk-group List hunt-group Setting rules for daylight savings time Type change daylight-savings-rules and press EnterSetting locations if necessary Type change locations and press EnterClearing and resolving alarms Verifying the date and the timeEnabling and disabling the Ethernet switch ports Click Submit Changes Enabling alarms to Inads by way of a modem Backing up files to the compact flash mediaEnabling alarms to Inads by way of the Snmp module Before leaving the siteInstallation verification Testing the Ipsi circuit packTesting the license file S8500 LEDs S8500 front-panel LEDs DescriptionAdditional media server LED information Rear view of S8500B Media ServerAvaya C360 Ethernet switch LEDs LAGLEDs on the Powerware 9125 UPS UPS LEDsTN2312BP Ipsi LEDs TN2312BP Ipsi circuit pack faceplate Ipsi LED display for a static IP address Connectivity status Appendix a Media server access Accessing the command line interface of the server withBackspace key area, select Control-H Connecting to the media server directly Cadlsrv3 KLC Connecting to the media server remotely over the network Connecting to the media server remotely over a modemAccessing the Maintenance Web Interface Click Launch Maintenance Web InterfaceUsing the SAT command line prompt Logins for Avaya technicians and BusinessPartnersType of connection Procedure Configuring the network for Windows 2000 and XP Select Internet Protocol TCP/IPSubnet mask Setting the browser options for Internet Explorer Click on LAN settings, then AdvancedPage Appendix B Installation troubleshooting Problem Possible solutionPing 192.11.13.6 and press Enter Dhcp Press EnterProblem Possible solution Index Directly Remotely over modem Remotely over networkIpsi Enabling Setting version

Related manuals

Manual 72 pages 24.67 Kb