Avaya S8500 Installation verification, Testing the Ipsi circuit pack, Testing the license file

Page 77

Chapter 9: Installation verification

This chapter provides the following information about how to verify the media server installation and configuration:

●Testing the IPSI circuit packs

●Testing the license file

●Checking LED status indicators

-Media servers

-Avaya Ethernet switches

-Uninterruptible power supplies (UPSs)

-Circuit packs

Testing the IPSI circuit pack

The following steps test the clock and packet interface components within the TN2312BP IPSI circuit pack.

1.In a SAT command line, type test ipserver-interfaceUUC and press Enter, where UUC is the cabinet and the carrier in which the circuit pack is located.

2.Verify that the Test Results screen shows PASS in the Results column.

Testing the license file

! Important:

Wait at least 30 minutes after you install the Communication Manager license before you run this test.

1.On a SAT command line, type test license and press Enter.

2.Verify that the Test Results screen shows PASS in the Results column.

Installing and Configuring the Avaya S8500 Media Server

February 2007 77

Image 77

Contents Release Installing and Configuring the Avaya S8500 Media ServerAvaya Inc All Rights Reserved Introduction Media server configuration Install an S8500 Media Server as an LSP Index 101 Audience IntroductionHow to use Avaya installation documents Verifying that all the required equipment is on site Pre-installation requirementsPreinstallation tasks to complete at the customer site S8500 hardware Ensuring that the preinstallation tasks are completeS8500C front panel S8500B front panel UPS Equipment specificationsCD-ROM/DVD-ROM IDE S8500 Media Server specifications Feature S8500B S8500CAcoustical About Samp connections About the Server Availability Management ProcessorAbout Samp functionality Samp connections for S8500B Samp connections for S8500C About Samp softwareS8500 port connections About media server port connectionsS8500C Media Server connectivity guide Modem connectivity on the S8500 Media Server About modem connectionsModem options About media gatewaysAbout Processor Ethernet About Processor Ethernet About S8500 LSP mode About SSH S8500 LSP license fileTN8412AP Sipi Configuring the Snmp modules in the UPS Snmp ConfigurationPrerequisites for configuring the Snmp module Default IP addresses for the UPSSecurity Alert Administering the Snmp moduleSetting selected traps alarming Preparing to configure the Ethernet switch Default IP addresses for the Ethernet switchConfiguring the Ethernet switch Page Page Clearing the ARP cache on the laptop Communication Manager installationConfiguring Telnet for Windows 2000 and Windows XP Applying power to the media serverAccessing the media server Installing Avaya Communication Manager Communication Manager installation Media server configuration Creating a super-user login Opening the Maintenance Web InterfaceUnder Security, select Administrator Accounts Type susers in the login group fieldAbout the Avaya Installation Wizard Installing Samp firmware Running the Avaya Installation WizardType sampcmd samp-update status and press Enter Verifying the RMB IP informationClick Execute Ping Configuring the modemSelect Configure individual services and click Continue Enabling firewall settingsSelect Change Modem Setting and click Continue Enabling network time serversEnabling network time servers Checking LED activity on the dual NIC Configuring the NICConfiguring the NIC Click Continue Disconnecting from the media serverInputting initial system translations IP interface translationsCabinet Cabinet Description Adding media gatewaysEnabling the Ipsi Set the Ipsi Control of Port Networks field to enabledAdding the Ipsi to the system Setting the alarm activation levelSaving translations Type add ipserver-interface PNnumber and press EnterConnecting to the IPSIs IP interface configurationProgramming the Ipsi for static addressing Ipsi address configurationConnecting the laptop directly to the Ipsi Type show control interface and press Enter Setting the Vlan and diffserv parameters Ipsi LED display for static address CLK Programming the Ipsi for Dhcp addressingIP interface configuration CLK Verifying connectivity to the media serverUpgrading the Ipsi firmware version if necessary Verifying that the IPSIs are translatedEnabling control of the IPSIs Verifying the license statusConfiguring the media server as an LSP Install an S8500 Media Server as an LSPSelect This is a local survivable processor LSP Select the Configure Individual ServicesSelect Set Identities Enabling license server capability on a media gateway Administering the primary controllerType stop -caf Type start -caf Installing and verifying the license on the new LSPOpening the TCP ports on the S8500 LSP Resetting the S8500 LSPClick Advanced Setting Verifying that the primary controller identifies the new LSP Readministering media gateways to point to the LSPList station List trunk-group List hunt-group Postinstallation administrationVerifying translations Type change daylight-savings-rules and press Enter Setting rules for daylight savings timeType change locations and press Enter Setting locations if necessaryVerifying the date and the time Clearing and resolving alarmsEnabling and disabling the Ethernet switch ports Click Submit Changes Backing up files to the compact flash media Enabling alarms to Inads by way of a modemBefore leaving the site Enabling alarms to Inads by way of the Snmp moduleTesting the license file Installation verificationTesting the Ipsi circuit pack S8500 LEDs Description S8500 front-panel LEDsRear view of S8500B Media Server Additional media server LED informationLAG Avaya C360 Ethernet switch LEDsUPS LEDs LEDs on the Powerware 9125 UPSTN2312BP Ipsi LEDs TN2312BP Ipsi circuit pack faceplate Ipsi LED display for a static IP address Connectivity status Accessing the command line interface of the server with Appendix a Media server accessBackspace key area, select Control-H Connecting to the media server directly Cadlsrv3 KLC Connecting to the media server remotely over a modem Connecting to the media server remotely over the networkClick Launch Maintenance Web Interface Accessing the Maintenance Web InterfaceType of connection Procedure Using the SAT command line promptLogins for Avaya technicians and BusinessPartners Subnet mask Configuring the network for Windows 2000 and XPSelect Internet Protocol TCP/IP Click on LAN settings, then Advanced Setting the browser options for Internet ExplorerPage Problem Possible solution Appendix B Installation troubleshootingPing 192.11.13.6 and press Enter Press Enter DhcpProblem Possible solution Directly Remotely over modem Remotely over network IndexIpsi Enabling Setting version

Related manuals

Manual 72 pages 24.67 Kb