Vizio L42HDTV10A, GV42L HDTV I2c Interface to Display Controller, TDA8946 Application

Page 47

The receiver can also process the video data before it is output as show below figure

5. I2c Interface to Display Controller

The Controller I2c interface (CSDA, CSCL) on the MT8293 is a slave interface capable of running up to 400KHZ. This bus is used to configure the MT8293 by reading/writing to the appropriate registers. The MT8293 is accessible on the local I2c bits at two-device address. The logic state of the CI2CA pin is latched on the rising edge of REST# providing a choice of two pairs of device address.

Control of local I2c address with CI2CA pin

TDA8946 Application

In L32 TV the TDA8946AJ is a dual-channel audio power amplifier with DC gain control. It has an output power of 2 × 10 W at an 8 Ω load and a 12 V supply.

CONFIDENTIAL – DO NOT COPY	Page 7-28
	File No. SG-0198

Image 47

Contents Vizio GV42L Hdtv Table of Contents Vinc Features Power Supply SpecificationOptical Characteristics Speaker Dimensions Physical dimension Width 1066 mmWeight Physical weight Mounting PrecautionsOperating Precautions Handling Precautions for Protection TV Source On Screen DisplayRGB Mode AV Component Mode Hdmi MODE： Confidential do not Copy Factory preset timings Pin Assignment Hdmi Connect PIN Assignment Type TV RF connector RGB Signal Main Board I/o Connections Theory of Circuit Operation MT8202 Application Decoder YPbPr/Scart/D-connectorVideo input Support Formats Digital port2D-Graphic/OSD processor Supporting OSD mirror and upside downMicroprocessor interface I/O ports are configured as follows：Video processor 1.Color Management Dram Usage DDR Sdram V58C2128164SBI5 Application Pin description Power-UpFunctional Description Command Truth TableMode Register Set MRS Precharge Bank Activate Command Precharge Timing During Read Operation Read OperationPrecharge Timing During Write Operation Burst Stop CommandBurst Write Operation MX29LV160BTTC Flash Application Block Diagram Command Definitions Write COMMANDS/COMMAND Sequences READ/RESET Command WM8776 Application Reading Array DataAudio sample rate Slave mode Confidential do not Copy MT8293 Application Video Data Conversion and Video Output Tmds Digital CoreActive port detection Hdcp DecryptionTDA8946 Application I2c Interface to Display ControllerBlock diagram Input configuration Output power measurement MT5351 Application Mode selectionGeneral Feature List CGMS/WSS Confidential do not Copy MX29LV320BTTC Flash Application Confidential do not Copy Block Diagram BUS OPERATION--1 BUS OPERATION--2 Write COMMANDS/COMMAND SequencesTable A. MX29LV320AT/B Command Definitions Reset Operation Standby ModeWrite Protect WP Software Command DefinitionsTable B. Write Operation Status Write Operation StatusFig C. Command Write Operation Fig D. Read Timing Waveforms Fig E. Reset Timing Waveform Functional Description Block Diagram 16Mb xDDR Sdram NT5DS16M16CS-5T Application Pin Configuration 400mil Tsop II x4 / x8 Mode Register Operation Operating Mode Extended Mode Register Definition Extended Mode RegisterActive Truth Table a CommandsSelf Refresh ReadWrite Auto RefreshReads OperationsRandom Read Accesses CAS Latencies Burst Length = 2, 4 or Read Command Write Command Data Input Write Data Output Read PC MODE1366X768 60HZ WaveformsCH1 Green # FB27 CH2 Vgavsync L22 CH1 Vgal R193 CH2 Avol R194 CH1 PCL CE70+ PCL CE70 AV&TV Mode AV1/AV2/TV Video Confidential do not Copy CH1 Dacbclk U23 PIN4 CH1 Dacmclk U23 PIN5 Component Mode Component 1/2 CH1YCBCRL2L19 CH2 2A33 U22 PIN11 CH1 AVL CE71+CH2 Auspl R304 Hdmi 1&2 Confidential do not Copy DTV HD Confidential do not Copy CH1 Vovsync DU9 PIN W1 CH1 Vode DU9 PIN W2 CH1 Vopclk DU9 PIN Monitor Display Nothing PC Mode Trouble shootingTV, Composite VIDEO1, 2, S-VIDEO is not Display Correctly COMPONENT1, 2 is not Display Correctly Hdmi is not Display Correctly Trouble of DC-DC Converter Trouble of DDC Reading System Block Diagram Wxga panel Block DiagramConfidential do not Copy Main Board Block Diagram Page Page Page Page Page Page Page